Ryobi RAG950-125 User manual

ORIGINAL INSTRUCTIONS
Angle Grinder
RAG950-125
RAG1010-125

Important!
It is essential that you read the instructions in this manual before assembling,
operating, and maintaining the product.
Subject to technical modification.

1
Safety, performance, and dependability have been given
top priority in the design of your angle grinder.
INTENDED USE
The angle grinder is intended to be used only by adults who
have read and understood the instructions and warnings
in this manual and can be considered responsible for their
actions. The angle grinder is designed for grinding and
cutting metals only. Only appropriate grinding discs as
GHVFULEHGLQWKHSURGXFWVSHFL¿FDWLRQVHFWLRQRIWKLVPDQXDO
VKRXOGEH¿WWHGWRWKHDQJOHJULQGHU7KHDQJOHJULQGHULV
designed for handheld use; it is not to be mounted onto a
¿[WXUHRUZRUNEHQFK
GENERAL POWER TOOL SAFETY WARNINGS
WARNING
Read all safety warnings and all instructions. Failure
to follow the warnings and instructions may result in
HOHFWULFVKRFN¿UHDQGRUVHULRXVLQMXU\
Save all warnings and instructions for future reference.
The term “power tool’’ in the warnings refers to your
mains-operated (corded) power tool or battery-operated
(cordless) power tool.
1) WORK AREA SAFETY
a) Keep work area clean and well lit. Cluttered or
GDUNDUHDVLQYLWHDFFLGHQWV
b) Do not operate power tools in explosive
atmospheres, such as in the presence of
flammable liquids, gases or dust. Power tools
FUHDWHVSDUNVZKLFKPD\LJQLWHWKHGXVWRUIXPHV
c) Keep children and bystanders away while
operating a power tool. Distractions can cause
you to lose control.
2) ELECTRICAL SAFETY
a) Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power
tools. Unmodified plugs and matching outlets will
UHGXFHULVNRIHOHFWULFVKRFN
b) Avoid body contact with earthed or grounded
surfaces, such as pipes, radiators, ranges and
refrigerators.7KHUHLVDQLQFUHDVHGULVNRIHOHFWULF
VKRFNLI\RXUERG\LVHDUWKHGRUJURXQGHG
c) Do not expose power tools to rain or wet
conditions. Water entering a power tool will
LQFUHDVHWKHULVNRIHOHFWULFVKRFN
d) Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges
or moving parts. Damaged or entangled cords
LQFUHDVHWKHULVNRIHOHFWULFVKRFN
e) When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of
DFRUGVXLWDEOHIRURXWGRRUXVHUHGXFHVWKHULVNRI
HOHFWULFVKRFN
f) If operating a power tool in a damp location
is unavoidable, use a residual current device
(RCD) protected supply. Use of an RCD reduces
WKHULVNRIHOHFWULFVKRFN
3) PERSONAL SAFETY
a) Stay alert, watch what you are doing and
use common sense when operating a power
tool. Do not use a power tool while you are
tired or under the influence of drugs, alcohol
or medication. A moment of inattention while
operating power tools may result in serious
SHUVRQDOLQMXU\
b) Use personal protective equipment. Always
wear eye protection. Protective equipment such
DVGXVWPDVNQRQVNLG VDIHW\VKRHVKDUGKDW RU
hearing protection used for appropriate conditions
ZLOOUHGXFHSHUVRQDOLQMXULHV
c) Prevent unintentional starting. Ensure the
switch is in the off-position before connecting
to power source and/or battery pack, picking
up or carrying the tool. Carrying power tools with
your finger on the switch or energising power tools
that have the switch on invites accidents.
d) Remove any adjusting key or wrench before
turning the power tool on.$ZUHQFKRUDNH\OHIW
attached to a rotating part of the power tool may
UHVXOWLQSHUVRQDOLQMXU\
e) Do not overreach. Keep proper footing and
balance at all times. This enables better control
RIWKHSRZHUWRROLQXQH[SHFWHGVLWXDWLRQV
f) Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves
away from moving parts./RRVHFORWKHVMHZHOOHU\
or long hair can be caught in moving parts.
g) If devices are provided for the connection of
dust extraction and collection facilities, ensure
these are connected and properly used. Use of
dust collection can reduce dust-related hazards.
4) POWER TOOL USE AND CARE
a) Do not force the power tool. Use the correct
power tool for your application. The correct
SRZHU WRRO ZLOO GR WKH MRE EHWWHU DQG VDIHU DW WKH
rate for which it was designed.
b) Do not use the power tool if the switch does not
turn it on and off. Any power tool that cannot be
controlled with the switch is dangerous and must
be repaired.
c) Disconnect the plug from the power source
and/or the battery pack from the power tool
before making any adjustments, changing
accessories or storing power tools. Such
SUHYHQWLYH VDIHW\ PHDVXUHV UHGXFH WKH ULVN RI
starting the power tool accidentally.
d) Store idle power tools out of the reach of
children and do not allow persons unfamiliar
with the power tool or these instructions
to operate the power tool. Power tools are
dangerous in the hands of untrained users.
e) Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts
and any other condition that may affect the
power tool’s operation. If damaged, have the
power tool repaired before use. Many accidents
are caused by poorly maintained power tools.
f) Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges
DUHOHVVOLNHO\WRELQGDQGDUHHDVLHUWRFRQWURO
g) Use the power tool, accessories and tool bits
etc, in accordance with these instructions,

2
taking into account the working conditions and
the work to be performed. Use of the power tool
for operations different from those intended could
result in a hazardous situation.
SERVICE
Have your power tool serviced by a qualified repair
person using only identical replacement parts. This will
ensure that the safety of the power tool is maintained.
ANGLE GRINDER SAFETY WARNINGS
SAFETY WARNINGS COMMON FOR GRINDING OR
ABRASIVE CUTTING-OFF OPERATIONS:
a) This power tool is intended to function as a
grinder or cut-off tool. Read all safety warnings,
instructions, illustrations and specifications
provided with this power tool. Failure to follow
all instructions listed below may result in electric
VKRFNILUHDQGRUVHULRXVLQMXU\
b) Operations such as sanding, wire brushing
or polishing are not recommended to be
performed with this power tool. Operations for
which the power tool was not designed may create
DKD]DUGDQGFDXVHSHUVRQDOLQMXU\
c) Do not use accessories which are not
specifically designed and recommended by the
tool manufacturer. Just because the accessory
can be attached to your power tool does not assure
safe operation.
d) The rated speed of the accessory must be at
least equal to the maximum speed marked on
the power tool. Accessories running faster than
WKHLUUDWHGVSHHGFDQEUHDNDQGIO\DSDUW
e) The outside diameter and the thickness of your
accessory must be within the capacity rating
of your power tool. Incorrectly sized accessories
cannot be adequately guarded or controlled.
f) Threaded mounting of accessories must match
the grinder spindle thread. For accessories
mounted by flanges, the arbour hole of the
accessory must fit the locating diameter of
the flange. Accessories that to do not match the
mounting hardware of the power tool will run out of
EDODQFH YLEUDWH H[FHVVLYHO\ DQG PD\ FDXVH ORVV
of control.
g) Do not use a damaged accessory. Before each
use inspect the accessory such as abrasive
wheels for chips and cracks, backing pad
for cracks, tear or excess wear, wire brush
for loose or cracked wires. If power tool or
accessory is dropped, inspect for damage
or install an undamaged accessory. After
inspecting and installing an accessory,
position yourself and bystanders away from
the plane of the rotating accessory and run the
power tool at maximum no-load speed for one
minute.'DPDJHGDFFHVVRULHVZLOOQRUPDOO\EUHDN
apart during this test time.
h) Wear personal protective equipment.
Depending on application, use face
shield, safety goggles or safety glasses.
As appropriate, wear dust mask, hearing
protectors, gloves and workshop apron
capable of stopping small abrasive or
workpiece fragments. The eye protection must
be capable of stopping flying debris generated by
YDULRXV RSHUDWLRQV 7KH GXVW PDVN RU UHVSLUDWRU
must be capable of filtrating particles generated
E\ \RXU RSHUDWLRQ 3URORQJHG H[SRVXUH WR KLJK
intensity noise may cause hearing loss.
i) Keep bystanders a safe distance away from
work area. Anyone entering the work area must
wear personal protective equipment. Fragments
RI ZRUNSLHFH RU RI D EURNHQ DFFHVVRU\ PD\ IO\
DZD\DQGFDXVHLQMXU\EH\RQGLPPHGLDWHDUHDRI
operation.
M Hold the power tool by insulated gripping
surfaces only, when performing an operation
where the cutting accessory may contact
hidden wiring or its own cord. Cutting accessory
FRQWDFWLQJD³OLYH´ZLUH PD\ PDNHH[SRVHGPHWDO
parts of the power tool “live” and could give the
RSHUDWRUDQHOHFWULFVKRFN
N Position the cord clear of the spinning
accessory. If you lose control, the cord may be cut
or snagged and your hand or arm may be pulled
into the spinning accessory.
l) Never lay the power tool down until the
accessory has come to a complete stop. The
spinning accessory may grab the surface and pull
the power tool out of your control.
m) Do not run the power tool while carrying it at
your side. Accidental contact with the spinning
accessory could snag your clothing, pulling the
accessory into your body.
n) Regularly clean the power tool’s air vents. The
motor’s fan will draw the dust inside the housing
DQG H[FHVVLYH DFFXPXODWLRQ RI SRZGHUHG PHWDO
may cause electrical hazards.
o) Do not operate the power tool near flammable
materials.6SDUNVFRXOGLJQLWHWKHVHPDWHULDOV
p) Do not use accessories that require liquid
coolants. Using water or other liquid coolants may
UHVXOWLQHOHFWURFXWLRQRUVKRFN
FURTHER SAFETY INSTRUCTIONS FOR ALL
OPERATIONS
Kickback and related warnings
.LFNEDFN LV D VXGGHQ UHDFWLRQ WR D SLQFKHG RU VQDJJHG
URWDWLQJZKHHOEDFNLQJSDGEUXVKRUDQ\RWKHUDFFHVVRU\
Pinching or snagging causes rapid stalling of the rotating
accessory, which in turn causes the uncontrolled power
tool to be forced in the direction opposite of the accessory’s
rotation at the point of the binding.
)RUH[DPSOHLI DQDEUDVLYH ZKHHOLVVQDJJHG RUSLQFKHG
E\ WKH ZRUNSLHFH WKH HGJH RI WKH ZKHHO WKDW LV HQWHULQJ
into the pinch point can dig into the surface of the material
FDXVLQJWKHZKHHOWRFOLPERXWRUNLFNRXW7KHZKHHOPD\
HLWKHUMXPSWRZDUG RUDZD\IURP WKHRSHUDWRU GHSHQGLQJ
on the direction of the wheel’s movement at the point of
SLQFKLQJ $EUDVLYH ZKHHOV PD\ DOVR EUHDN XQGHU WKHVH
conditions.
.LFNEDFNLVWKHUHVXOWRISRZHUWRROPLVXVHDQGRULQFRUUHFW
operating procedures or conditions and can be avoided by
WDNLQJSURSHUSUHFDXWLRQVDVJLYHQEHORZ
a) Maintain a firm grip on the power tool and
position your body and arm to allow you to
resist kickback forces. Always use auxiliary
handle, if provided, for maximum control
over kickback or torque reaction during start-
up. The operator can control torque reactions or
NLFNEDFNIRUFHVLISURSHUSUHFDXWLRQVDUHWDNHQ
b) Never place your hand near the rotating
accessory. $FFHVVRU\ PD\ NLFNEDFN RYHU \RXU

3
hand.
c) Do not position your body in the area where
power tool will move if kickback occurs.
.LFNEDFN ZLOO SURSHO WKH WRRO LQ GLUHFWLRQ RSSRVLWH
to the wheel’s movement at the point of snagging.
d) Use special care when working corners, sharp
edges, etc. Avoid bouncing and snagging the
accessory. Corners, sharp edges or bouncing
have a tendency to snag the rotating accessory
DQGFDXVHORVVRIFRQWURORUNLFNEDFN
e) Do not attach a saw chain woodcarving blade
or toothed saw blade. Such blades create
IUHTXHQWNLFNEDFNDQGORVVRIFRQWURO
ADDITIONAL SAFETY INSTRUCTIONS FOR GRINDING
AND CUTTING-OFF OPERATIONS
6DIHW\ ZDUQLQJV VSHFL¿F IRU JULQGLQJ DQG DEUDVLYH
cutting-off operations:
a) Use only wheel types that are recommended
for your power tool and the specific guard
designed for the selected wheel. Wheels for
which the power tool was not designed cannot be
adequately guarded and are unsafe.
b) The grinding surface of centre depressed
wheels must be mounted below the plane of
the guard lip. An improperly mounted wheel that
SURMHFWVWKURXJKWKHSODQHRIWKHJXDUGOLSFDQQRW
be adequately protected.
c) The guard must be securely attached to the
power tool and positioned for maximum safety,
so the least amount of wheel is exposed
towards the operator. The guard helps to protect
WKH RSHUDWRU IURP EURNHQ ZKHHO IUDJPHQWV
DFFLGHQWDO FRQWDFW ZLWK ZKHHO DQG VSDUNV WKDW
could ignite clothing.
d) Wheels must be used only for recommended
applications. For example: Do not grind with
the side of cut-off wheel. Abrasive cut-off wheels
are intended for peripheral grinding, side forces
applied to these wheels may cause them to shatter.
e) Always use undamaged wheel flanges that are
of correct size and shape for your selected
wheel. Proper wheel flanges support the wheel,
WKXV UHGXFLQJ WKH SRVVLELOLW\ RI ZKHHO EUHDNDJH
Flanges for cut-off wheels may be different from
grinding wheel flanges.
f) Do not use worn down wheels from larger
power tools. Wheel intended for larger power tool
is not suitable for the higher speed of a smaller tool
and may burst.
ADDITIONAL SAFETY WARNINGS SPECIFIC FOR
ABRASIVE CUTTING-OFF OPERATIONS
a) Do not “jam” the cut-off wheel or apply
excessive pressure. Do not attempt to make an
excessive depth of cut. Overstressing the wheel
increases the loading and susceptibility to twisting
or binding of the wheel in the cut and the possibility
RINLFNEDFNRUZKHHOEUHDNDJH
b) Do not position your body in line with and
behind the rotating wheel. When the wheel,
at the point of operation, is moving away from
\RXU ERG\ WKH SRVVLEOH NLFNEDFN PD\ SURSHO WKH
spinning wheel and the power tool directly at you.
c) When wheel is binding or when interrupting a
cut for any reason, switch off the power tool
and hold the power tool motionless until the
wheel comes to a complete stop. Never attempt
to remove the cut-off wheel from the cut while
the wheel is in motion otherwise kickback may
occur. ,QYHVWLJDWH DQG WDNH FRUUHFWLYH DFWLRQ WR
eliminate the cause of wheel binding.
d) Do not restart the cutting operation in the
workpiece. Let the wheel reach full speed and
carefully re-enter the cut. The wheel may bind,
ZDONXS RU NLFNEDFN LI WKH SRZHU WRRO LV UHVWDUWHG
LQWKHZRUNSLHFH
e) Support panels or any oversized workpiece
to minimize the risk of wheel pinching and
kickback. /DUJH ZRUNSLHFHV WHQG WR VDJ XQGHU
their own weight. Supports must be placed under
WKH ZRUNSLHFH QHDU WKH OLQH RI FXW DQG QHDU WKH
HGJHRIWKHZRUNSLHFHRQERWKVLGHVRIWKHZKHHO
f) Use extra caution when making a “pocket
cut” into existing walls or other blind areas.
The protruding wheel may cut gas or water pipes,
HOHFWULFDOZLULQJRUREMHFWVWKDWFDQFDXVHNLFNEDFN
ANGLE GRINDER SAFETY PRECAUTIONS
a) &KHFN WKDW WKH VSHHG PDUNHG RQ WKH JULQGLQJ
wheel is equal to or greater than the rated speed
of the product.
b) Ensure that the dimensions of the grinding wheel
are compatible with the product and that the wheel
fits the spindle.
c) Grinding wheels must be stored in a dry place.
d) 'RQRWVWRUHREMHFWVRQWRSRIWKHJULQGLQJZKHHOV
e) Grinding wheels must not be used for any operation
other than grinding.
f) Grinding wheels must be stored and handled
with care in accordance with the manufacturer’s
instruction.
g) Inspect the grinding wheel before use to ensure
WKDWLW LV QRW FKLSSHG RUFUDFNHG &KLSV RUFUDFNV
can cause the wheels to shatter, resulting in
SRVVLEOHVHULRXVLQMXU\
h) Ensure that the wheel is fitted in accordance with
this manual.
i) Ensure that the grinding wheel is correctly mounted
and tightened before use and run the product at
no-load speed for 30 seconds in a safe position.
Stop immediately if there is considerable vibration
or if other defects are detected. If this condition
RFFXUVFKHFNWKHWRROWRGHWHUPLQHWKHFDXVH
M Do not use separate reducing bushings or adapters
to adapt large hole grinding wheels.
N &KHFNWKDWWKHZRUNSLHFHLVSURSHUO\VXSSRUWHG
l) Use only grinding wheels approved by RYOBI.
m) (QVXUH WKDW VSDUNV UHVXOWLQJ IURP XVH GR QRW
create a hazard, e.g., do not hit people, or ignite
flammable substances.
n) Always use protective safety glasses and ear
protectors.
o) Use other personal protective equipment, such as
gloves, apron, and helmet, when necessary.
p) Never place the product on the floor or other

4
surfaces while it is running. Grinding wheels
continue to rotate after the product is switched off.
Never touch the wheel or place it on the floor or
other surfaces while it is rotating.
q) Use the product only for approved applications.
Never use coolants or water or use the tool as a
IL[HGWRRO
r) Grip the product securely with both hands while
operating.
RESIDUAL RISKS
Even when the angle grinder is used as prescribed, it is
VWLOOLPSRVVLEOHWRFRPSOHWHO\HOLPLQDWHFHUWDLQUHVLGXDOULVN
factors. The following hazards may arise and the operator
should pay special attention to avoid the following:
Ŷ ,QMXU\FDXVHGE\WKURZQRIISDUWLFOHV
– Metal or abrasive particles may enter the eyes and
cause severe permanent damage. Wear goggles
approved for grinding operations when operating
the product.
Ŷ ,QMXU\FDXVHGE\YLEUDWLRQ
– /LPLWH[SRVXUH6HH5LVN5HGXFWLRQ
Ŷ ,QMXU\FDXVHGE\GXVW
– :HDU DSSURSULDWH GXVW FRQWURO PDVN ZLWK ILOWHUV
suitable for protecting against particles from the
PDWHULDO EHLQJ ZRUNHG RQ DQG DEUDVLYH SDUWLFOHV
IURPWKHJULQGLQJGLVF'RQRWHDWGULQNRUVPRNH
LQWKHZRUNDUHD(QVXUHDGHTXDWHYHQWLODWLRQ
Ŷ ,QMXU\IURPFRQWDFWZLWKWKHJULQGLQJGLVF
– 7KH GLVF DQG ZRUNSLHFH ZLOO EHFRPH KRW GXULQJ
use. Wear gloves when changing discs or touching
ZRUNSLHFH .HHS KDQGV DZD\ IURP WKH JULQGLQJ
DUHD DW DOO WLPHV &ODPS WKH ZRUNSLHFH ZKHQHYHU
possible.
Ŷ ,QMXU\FDXVHGE\QRLVH
– 3URORQJHGH[SRVXUHWR QRLVH ZLOOLQFUHDVHWKH ULVN
of hearing damage, and the effects are cumulative.
:KHQXVLQJSRZHUWRROVIRUDQH[WHQGHGSHULRGRI
time, wear hearing protection.
RISK REDUCTION
It has been reported that vibrations from handheld tools
may contribute to a condition called Raynaud’s Syndrome
in certain individuals. Symptoms may include tingling,
QXPEQHVVDQG EODQFKLQJ RI WKH¿QJHUV XVXDOO\ DSSDUHQW
XSRQ H[SRVXUH WR FROG +HUHGLWDU\ IDFWRUV H[SRVXUH WR
FROG DQG GDPSQHVV GLHW VPRNLQJ DQG ZRUN SUDFWLFHV
are all thought to contribute to the development of these
V\PSWRPV7KHUHDUHPHDVXUHVWKDWFDQEHWDNHQ E\ WKH
operator to possibly reduce the effects of vibration:
ŶKeep your body warm in cold weather. When operating
WKHSURGXFWZHDUJORYHVWRNHHSWKHKDQGVDQGZULVWV
ZDUP,WLVUHSRUWHGWKDWFROGZHDWKHULVDPDMRUIDFWRU
contributing to Raynaud’s Syndrome.
Ŷ $IWHU HDFK SHULRG RI RSHUDWLRQ H[HUFLVH WR LQFUHDVH
blood circulation.
Ŷ 7DNH IUHTXHQW ZRUN EUHDNV /LPLW WKH DPRXQW RI
H[SRVXUHSHUGD\
,I \RX H[SHULHQFH DQ\ RI WKH V\PSWRPV RI WKLV FRQGLWLRQ
immediately discontinue use and see your doctor about
these symptoms.
WARNING
,QMXULHVPD\EHFDXVHGRUDJJUDYDWHGE\SURORQJHGXVH
of a tool. When using any tool for prolonged periods,
HQVXUH\RXWDNHUHJXODUEUHDNV
KNOW YOUR PRODUCT
See page 7.
1. Switch button
2. 6SLQGOHORFNEXWWRQ
3. *XDUGOHYHUORFN
4. Wheel guard assembly
5. Clamp nut
6. Grinding wheel
7. Disc flange
8. $X[LOLDU\KDQGOH
9. Wrench
10. (DV\IL[QXW
STARTUP PROTECTION
0DFKLQHV ZLWK D ORFNRQ VZLWFK DUH ¿WWHG ZLWK D FXWRXW
This prevents the machine from restarting by itself after a
SRZHUIDLOXUH:KHQUHVXPLQJZRUNVZLWFKWKHPDFKLQHRII
DQGWKHQVZLWFKLWEDFNRQDJDLQ
MAINTENANCE
WARNING
'R QRW PDNH DQ\ DGMXVWPHQWV ZKLOH WKH PRWRU LV LQ
motion.
The product should never be connected to a power
VXSSO\ ZKHQ DVVHPEOLQJ SDUWV PDNLQJ DGMXVWPHQWV
cleaning, performing maintenance, or when the product
is not in use. Disconnecting the product will prevent
DFFLGHQWDOVWDUWLQJWKDWFRXOGFDXVHVHULRXVLQMXU\
Ŷ $IWHUXVHFKHFNWKHWRROWRPDNHVXUHWKDWLWLVLQJRRG
condition.
Ŷ ,W LV UHFRPPHQGHG WKDW \RX WDNH WKLV WRRO WR D 5\REL
Authorized Service Center for a thorough cleaning and
lubrication at least once a year.
ŶIf the power supply cord is damaged, it must be
replaced only by the manufacturer or by an authorized
VHUYLFHFHQWHUWRDYRLGULVN&RQWDFWDXWKRUL]HGVHUYLFH
center.
WARNING
To ensure safety and reliability, all repairs should be
performed by an authorised service center or other
qualified service organisation.
WARNING
Do not use compressed air to blow dust from the grinder.
This practice is dangerous and can cause dirt and grit to
EHEODVWHGLQWRVRPHRQH¶VH\HVFDXVLQJVHULRXVLQMXU\

5
ENVIRONMENTAL PROTECTION
Recycle raw materials instead of disposing
of as waste. The machine, accessories
DQG SDFNDJLQJ VKRXOG EH VRUWHG IRU
environmental-friendly recycling.
SYMBOLS ON THE PRODUCT
Safety Alert
VVolts
+] +HUW]
Alternating current
W Watts
n Rated speed
PLQʚï Revolutions or reciprocations per minute
Class II tool, double insulation
Please read the instructions carefully before
starting the product.
Wear ear protection
Wear eye protection
:HDUGXVWPDVN
'RQRWXVHFKLSSHGFUDFNHGRUGHIHFWLYH
grinding wheel
Not for wet grinding. Using water or other
liquid coolants may result in electrocution or
VKRFN
Wear safety hand gloves
Do not use for face grinding.
Wear safety footwear.
:HDUH\HDQGHDUSURWHFWLRQDQGPDVN
(XU$VLDQ&RQIRUPLW\0DUN
CE Conformity
8NUDLQLDQPDUNRIFRQIRUPLW\
Waste electrical products should not be
disposed of with household waste. Please
UHF\FOHZKHUHIDFLOLWLHVH[LVW&KHFNZLWK\RXU
local authority or retailer for recycling advice.
SYMBOLS IN THIS MANUAL
Connect to the power supply.
Disconnect from the power supply.
Parts or accessories sold separately
Waste electrical products should not
be disposed of with household waste.
3OHDVHUHF\FOHZKHUHIDFLOLWLHVH[LVW
/RFN
8QORFN
Note
Warning
Stop the product.
The following signal words and meanings are intended to
H[SODLQWKHOHYHOVRIULVNDVVRFLDWHGZLWKWKLVSURGXFW
DANGER
Indicates an imminently hazardous situation, which, if not
DYRLGHGZLOOUHVXOWLQGHDWKRUVHULRXVLQMXU\
WARNING
Indicates a potentially hazardous situation, which, if not
DYRLGHGFRXOGUHVXOWLQGHDWKRUVHULRXVLQMXU\
CAUTION
Indicates a potentially hazardous situation, which, if not
DYRLGHGPD\UHVXOWLQPLQRURUPRGHUDWHLQMXU\
CAUTION
(Without Safety Alert Symbol) Indicates a situation that
may result in property damage.

6
x 1
x 1
x 1
x 1
x 1
x 1
x 1
x 1
RAG950-125
RAG1010-125

7
RAG950-125
RAG950-125
RAG1010-125
8
2
3
4
510
6
7
1
9

8
2
1
3
2
RAG950-125
3
2
1
1

9
2
1
4
3
2
RAG1010-125
3
2
1
1

10
1
2
3
Û
5
5$*5$*

11
1
2
3
4
1
5
24
3
6

12
1
2
3
1
2
2
1
1
2

13
RAG950-125 RAG1010-125
1 1
22
RAG950-125 RAG1010-125
3
1
2
1
3
2
4

14
RAG950-125 RAG1010-125
2
1
RAG950-125 RAG1010-125
1
2
1
2
3
5
6
7
RAG950-125 RAG1010-125

15
5
1
2
3
4
8
9

16
RAG950-125 RAG1010-125
1 1
22
RAG950-125 RAG1010-125
RAG950-125 RAG1010-125
1
3
2
4

17
RAG950-125 RAG1010-125
RAG950-125 RAG1010-125
1
2
1
2
3
5
20151013v1

VIBRATION LEVEL
WARNING
The vibration emission level given in this information sheet has been measured in accordance with a standardised test
given in EN 60745 and may be used to compare one tool with another. It may be used for a preliminary assessment of
exposure. The declared vibration emission level represents the main applications of the tool. However if the tool is used
for different applications, with different accessories or poorly maintained, the vibration emission may differ. This may
signicantly increase the exposure level over the total working period.
An estimation of the level of exposure to vibration should also take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may signicantly reduce the exposure level over the total working
period. Identify additional safety measures to protect the operator from the effects of vibration such as: maintain the tool
and the accessories, keep the hands warm, organisation of work patterns.
PRODUCT SPECIFICATIONS
Angle Grinder
Model RAG950-125 RAG1010-125
Grinding wheel:
Diameter 125 mm (5 in.) 125 mm (5 in.)
Thickness 6 mm 6 mm
Cutting wheel:
Diameter 125 mm (5 in.) 125 mm (5 in.)
Thickness 3 mm 3 mm
Diamond wheel:
Diameter 125 mm (5 in.) 125 mm (5 in.)
Thickness 2 mm 2 mm
Rated voltage 220 - 240 V
50 / 60 Hz
220 - 240 V
50 / 60 Hz
Rated capacity 125 mm 125 mm
Input 950 W 1010 W
Spindle thread M 14 M 14
Rated speed 12,000 min-1 12,000 min-1
Net weight 2.45 kg 2.45 kg
Measured sound values determined according to EN 60745:
A-weighted sound pressure level LpA = 89.5 dB(A) LpA = 89.5 dB(A)
Uncertainty K 3 dB 3 dB
A-weighted sound power level LWA = 100.5 dB(A) LWA = 100.5 dB(A)
Uncertainty K 3 dB 3 dB
Wear ear protectors.
The vibration total values (triaxial vector sum) determined according to EN 60745:
Surface grinding, Vibration emission level ah,AG = 8.4 m/s2ah,AG = 8.4 m/s2
Uncertainty K 1.5 m/s21.5 m/s2