S-1 CDR-0130 User manual

User's Manual
For Smart Card Reader(CDR-0130)
S1 CORPORATION

Smart Card Reader(CDR-0130)
Smart card reader is amachine controlling access management and making
block mode change in GBMS. Power is supplied by auxiliary power
equipment or local controllerⅡ. lock controller.
Access management function transmits the data to lock controller as it
reads recorded data in card by the method of making customer or traverse
card approach to card reader. Lock controller makes access available by
controlling lock/auto door of entrance door after checking whether
received data is registered or not.
Mode change function transmits the data to lock controller as it reads
recorded data in card by the method of making customer or traverse card
approach to card reader keeping pushed SECOM button of smart card
reader. Controller selects guard modes such as set/cancel/traverse by
checking whether the received data is registered or not.
Use Environment
(1) Use temperature :-20℃ ∼＋45℃
(2) Use humidity :30％ ∼90％(relative humidity)
(3) Installation requirements
－Convenient Place for manipulating machine.
－Install on none-metal.
－Place which is not affected by raining.
－Place which has not direct ray.
－Place which is not affected by heat.
－Place which has not vibration.
－Install at the place that reading distance should be kept more than 5CM.

Beep sound & Guiding voice
Trough speaker, guiding voice is given as followings. And beep sends
confirming sound.
Guiding voice
Standard Specifications
* size : 95(W) × 140(H) × 28(D) 〔 mm〕
*
Weight : about 234g
*
Working voltage : DC 17.0 ∼ 28.0V
*
Current consumption : Power index 1.3 (less than DC 24V 195mA)
NO Working Type Working condition Stopping Condition
1 Beep sound
At
normal input of card
data,
one time working
(ON for 200ms)
2 Guiding voice At card manupulating
No guiding voice at normal
access approval
NO Contents Remarks
1 The system has been armed. Set
2 Hello! The system has been disarmed. Cancel
3
Peep!
Peep! Peep! You cannot arm the system.
Please
go inside and check the problem areas.
Then
run your key card again.
Troubles
4 There's an error in the card. IC Chip defective
5 The system is armed, please disarm the system. Card working at set
6 Your security card is not valid. Access
trying with
none-register
card
7 Your security card passed its valid date. Card
passed its
valid date

FCC Regulatory Compliance : Notices Class B Equipment
This equipment has been tested and found to comply with the limits for a
Class B digital device pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or
more of the following measures :
-
Reorient or relocate the receiving antenna.
-
Increase the separation between the equipment and receiver.
-
Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
-
Consult the dealer or an experienced radio TV technician for help.
This device complies with part 15 of the FCC Rules.
Operations is subject to the following two conditions :
(1) This device may not cause harmful interference and (2) this device
must accept any interference received, including interference that may
cause undesired operation.
The user’s manual or instruction manual for an intentional or unintentional
radiator shall caution the user that changes or modifications not expressly
approved by the party responsible for compliance could void the user's
authority to operate the equipment.