Söol Fit Basic User manual

Copyright© Söol Corp 2020 - PS-0002-01C
Page 1 of 15
Söol Fit™ Basic - Installation Manual
Poplar Cherry Walnut

Copyright© Söol Corp 2020 - PS-0002-01C
Page 2 of 15
Installing Your Söol Fit™:
This Installation Manual is intended to guide a licensed and fully insured carpenter”Installer” through the steps
necessary to safely and properly install the Söol Fit™ Basic Model.
DISCLAIMER OF LIABILITY-
YOUR SOOL FIT™ COMES COMPLETE WITH TERMS AND CONDITIONS, AN OWNERS
MANUAL AND AN INSTALLATION MANUAL (THE “DOCUMENTATION”). YOUR SOOL
FIT™ INCLUDES MANY MOVING PARTS, REQUIRES COMPLETE COMPLIANCE WITH ALL
USE AND INSTALLATION INSTRUCTIONS AND MAY ALSO COME WITH THIRD-PARTY
EXERCISE OR OTHER EQUIPMENT. SOOL CORP. HEREBY DISCLAIMS ANY AND ALL
LIABILITY FOR DAMAGE TO PERSONS OR PROPERTY DIRECTLY OR INDIRECTLY RELATED
TO ANY FAILURE TO COMPLY WITH ALL INSTRUCTIONS, DIRECTIVES, WARNINGS AND
CAUTIONS CONTAINED IN ANY PORTION OF THE DOCUMENTATION AND FURTHER
HEREBY DISCLAIMS ANY AND ALL LIABILITY FOR DAMAGE TO PERSONS OR PROPERTY
DIRECTLY OR INDIRECTLY RELATED TO THE USE OF ANY THIRD-PARTY EXERCISE OR
OTHER EQUIPMENT.
Quick Reference Installation Steps:
Söol Fit™ - Basic
1Read this Installation Manual completely and observe all safety WARNINGS and CAUTIONS
throughout this manual
2Installer to verify site space requirements and wall construction before unpacking
3Unpack and verify contents
4Layout strut location and find studs
5Mount upper strut and lower strut (3-4 mounting points per strut)
6Perform any wall prep/trim removal as needed
7Mount frame to struts (8 mounting screws)
8Mount Bench assembly (pivot rod push nut, shoulder screw, gas spring mount)
9Wood cabinet assembly - Mount door assemblies right and left (16 screws)
10 Wood cabinet assembly - Mount front plates top/bottom with side panels right/left and
(16 screws)

Copyright© Söol Corp 2020 - PS-0002-01C
Page 3 of 15
Safety:
To ensure safe and proper installation, uninstallation or reinstallation, the Söol Fit™ owner “Buyer” must have two
Installers perform installation following the instructions provided.
-Take all lifting precautions and use proper body mechanics throughout entire installation
process, including when moving and lifting any assembly or carton. Always use two Installers
to lift and maneuver frame assembly during installation.
- An unsecured Söol Fit™ frame is a tip hazard. Use extreme caution when frame assembly is in
upright position and always have an assistant Installer securely hold frame until
bolted/anchored securely and completely to the wall, failure to do so can cause serious injury
or death.
- Installer must provide and ensure proper bolts/anchors are used to secure the struts based on
wall type, failure to do so may allow the Söol Fit™ to dislodge from wall and cause serious
injury or death.
- NEVER disassemble or modify the original factory configured Söol Fit™. It may cause serious
injury or death.
WARNING
!
WARNING
!
WARNING
!
WARNING
!

Copyright© Söol Corp 2020 - PS-0002-01C
Page 4 of 15
Site Requirement Verification:
During order process, the Buyer has confirmed site requirements for the Söol Fit™ model. It is recommended,
prior to unpacking or performing any site preparation, the installation location is verified by the Installer.
-I (Installer) have verified the mounting wall construction
Correct fasteners must be selected for wood studs, metal studs or concrete walls.
Optimum 16- inch stud centers (allows unlimited mounting location).
Minimum 24- inch stud centers (limits mounting location - strut must be bolted to 3 studs).
For concrete walls a minimum of four anchors/bolts must be used to secure each strut.

Copyright© Söol Corp 2020 - PS-0002-01C
Page 5 of 15
Verify Receipt of All Cartons and Items:
Carton
G
Carton
H
Carton
A
Carton
B
Carton
C
Carton
D,E
Carton
F
1A Frame assembly BASIC SA-0018-01 A-1 1
2 Bench assembly SA-0302-01
B
1
3 Shoulder screw 5/16 FS-SB002-01 1
4 Washer nylon .313x.5x.031 FS-W0001-02 1
5 Bench lift pivot rod MA-0006-01 1
6 Cap nut 3/8 FS-N0001-02 2
7 Washer nylon 375 x .570 x .031 FS-W0001-03 2
8 Wood side panel assy L WP-0302-xx C-x** 1
9 Wood side panel assy R WP-0303-xx 1
10 Wood door assy L WP-0104-xx D-x** 1
11 Wood door assy R WP-0103-xx E-x** 1
12 Wood front bottom plate assy WP-0009-1x F-x** 1
13 Wood front top plate WP-0004-0x 1
14 Wood Crown molding assy WP-0007-xx G-x** 1
22 Shelf WA-0004-03
H
1
23 Pad rubber 1" x 1 " PP-0017-01 9
24 Strut assy upper SA-0013-01 1
25
Basic
Item# Description Part # Carton # Qty
Strut channel Lower MP-0011-03 2
26 Strut washer 1/4" HW-0018-01 6
27 Strut channel nut 1/4-20 HW-0018-03 6
28 Screw BHPH 1/4-20 x 2 FS-S0006-04 10
29 Washer SS 1/4x3/4x.075 FS-W0005-02 12
30 Nut 1/4-20 w/ext lock FS-N0003-01 4
31 Screw FHPH 8-32 x 1/4 UC FS-S0008-01 16
32 Screw FH #10x5/8 w/ Hinge FS-S0009-04 16
** (1= Poplar, 2=Cherry, 3=Walnut)