SAFE JACK 51M-SJTP User manual

Safe Jack Stabilizer Instruction Manual
PN: 51102
Model Number: 51M-SJTP
PN Instruction : 51002

2
D, E
Jack
Standard
J
Top of Jack
Jack Base
A
CF
G, H
H, I, L
B
K

3
1. Unpack the 51M-SJTP, PN: 51102 and ensure that all parts are included:
The Stabilizer Legs should come in the box assembled.
Just unpack and attach to jack
If you are missing any parts please call 1-509-735-2106
Item Model Number PN Qty Description
A, B 51M-SJTP 51102 4 pieces Stabilizer Legs
C51M-CLEVIS 51111 1Clevis for Hi-Lift
D50C300HCS5Z 51121 11/2-13 x 3 Hex cap screw GR 5 Zinc
E50CNWI0Z 51122 11/2-13 WING NUT ZINC
F37R250PWQ0Z 51120 1Wire Bail Pin Zinc 3/8 x 2 1/2
G31C200HCS5Z 51123 25/16-18 X 2 HEX CAP SCREW GR 5 ZINC
H31CNWI0Z 51124 45/16-18 WING NUT ZINC
I31NWUS0Z 51125 25/16 USS FLAT WASHER ZINC
J51M-135CHAIN 51126
5ft .135 UTILITY LINK CHAIN 340# ZINC PLATED (51M-135CHAIN / _/10570C)
K37C100HCS5Z 51127 23/8 x 1" NC GR 5 Bolt Zinc
L31C250HCS5Z 51128 25/16-18 X 2 1/2 HEX CAP SCREW GR 5
ZINC
GENERAL SAFETY INFORMATION
The Safe Jack Stabilizer Legs cannot be over stressed that the safe operation
and condition of the jack used with the Universal Base Plate System is critical to the
overall safety of the operation. Follow the jack manufacturer’s operation
instructions or review the numerous instructional videos on You-Tube provided by
the jack manufactures and various specialists.

4
2. Lay your Hi-Lift or Hi-lift style
jack down on the ground as it
makes it much easier to attach the
parts without worrying about it
falling over on you. If you have a
(97M-UHS) Universal High Lift
Stabilizer attached you don’t need
to lay it down, just leave it in the
baseplate, standing up.
3. The feet should already be
attached to the chain as shown
(H, I, L).

5
4. Extend leg sections to the
appropriate hole. If you have a 48”
jack use the hole closest to the
foot, 60” use hole furthest from the
foot. Slide the bolt through and
secure using the provided wing
nuts (G, H). The bolt should act as
a stop and not actually go through
the top section of the legs.
5. Attach jack to leg—top section
(A) using bolt and nut (D, E) as
shown. (Finger tight).

6
6. Attach the clevis (C) to the
jack standard using the provided
bale pin (F).
7. Set Jack upright and swing
legs forward against the chains.
8. Rotate the bottom section of
the legs until the foot rests flat
on the ground (as shown on page
2) and the chain is spread evenly
per each side of the jack.
Tighten the tension nuts on the
bottom section of the legs (K),
securing the bottom and top
sections of the legs together.

7
Now go use your Safe Jack
Stabilizer Legs to help make your
life easier. Here’s a few things
we’ve used them for.
51M-SJSL
51M-SJSL [PN: 51103] 97M-UHS48/60 [PN: 97102 48”, 97103 60”]
Add our Safe Jack Secure Lifter and
Universal Hi Lift Stabilizer for added
safety and pulling/lifting power.

8
Safe Jack by Bogert Manufacturing Inc.
3606 N. Swallow Ave. Ste 200
Pasco, WA 99301 USA
[phone] Phone
[phone] Toll Free
[phone] Fax
www.safejacks.com