Safe Aurora User manual

AURORA
GROUP 0+1 ISOFIX
9- 18 KG

Important Notes
Overview
Using the Aurora Child Car seat
General Guidelines
For Isofix-Suitable Vehicles
Removing the seat
Mounng the Aurora
Mounng the Seat Opposite to the driving direcon
(From Birth to 13kg)
Mounng the seat in the driving direcon (From 9 to 18kg)
Securing your child in the Aurora
Using the reclining adjustment
Removing the insert for new born to 13kg
Care Instrucons
Warranty condions
02
03
04
05
06
07
08
09
10
11
12
13
14
15
01

02
Important Notes
Cauon!
Make sure you observe the relevant instrucons in the user manual
of your vehicle before transporng children. Take parcular note of
all informaon provided for the use of child seats in connecon with
airbags.
Warning!
• Children oen carry small objects (e.g.toys) in jacket or trouser
pockets, and may also wear clothes with rigid components (e.g. belt
buckle).
Make sure that these objects are not clamped between the child and
the safety harness, as this might cause unnecessary injuries in case of
an accident. The same hazards also apply for adults.
• Naturally young children are oen lively. Make sure to explain the
importance of safety when in a vehicle. Your child will then
understand that the harness lock should not be opened and the
harness should not be removed, giving you more peace of mind.
• Your child’s safety can only be guaranteed if the safety system is
installed and used in accordance with the instrucon manual.
• All system harness straps must be worn taut and without any
twists, and must be protected from demage.
• Protect any parts of the restraint system not covered with fabric
against direct sunlight to prevent your child from suffering burns.
• The child restraint system must not be damaged or crushed by
moving parts in the vehicle or by the vehicle doors.
• Do not aempt any modificaons to the restraint system as they
might endanger your child’s safety.
• Aer an accident, the enre child restraint system must be
replaced or sent to the manufacturer for tesng, along with an
accident report.
• Make sure to instruct your passenger on how to remove the child
from its safety seat in case of an accident or danger.
• The lap belts of the harness system must be fied as low down as
possible so that the child’s hips are held correctly.
• The child seat must not be used on seats with acvated front
airbags. (Danger to life)!

03
• Never leave your child unsupervised in the car seat – whether
harnessed or not.
• Make sure you secure any luggage and loose items to reduce the
risk of injury in case of an accident.
• The manual must always be carried with the child safety seat.
• The use of any accessories or replacement parts is prohibited, and
non-compliance with result in the lapse of all warranty and liability
claims.
• The child safety seat is to be used with original seat covers only.
• If the restraint system is used extensively it is normal for the seat
covers and other parts to suffer varying degrees of wear, depending
replaced. We can therefore not provided any blanket warranty
beyond 6 months for wear parts.
• Please contact your specialists shop for baby and children’s
accessory specialist shop or a catalogue company for replacement
seat accessories to choose from.
• The child seat has been tested crash simulaon.
for impacts of up to 50 km/h against a solid obstacle. Test results are
applicable for all tested child safety seat systems. When used as
to children up to a body weight of 18kg in case of an accident,
depending on the type and severity of accident.
• A child safety device does not replace responsible and careful
behavior in road traffic.
child

04
01
A
07
05
B
08
09
11
13
15
14
02
03
04
06
10
12

05
OVERVIEW
01.Headrest
02.Harness buckle
04.Central harness
06.Lockinghandlefor the seat lock
07.Safety display seatlock
08.Isofix system control dial
10.Support leg
11.Safety display for support leg
12.Front-Lock
13.Rear-Lock
USING THE AURORA CHILD CAR SEAT
Thank you for purchasing our car seat AURORA. The product
The baby car seat is suitablefor children up to the age of approx.
4orup to 18kg. It is suitable forusein vehicle with Isofix-approved
seats (see vehicle list) in accordance with the relevant child restraint
and anchoring category.
seat behind the frontpassenger seat.
Theseat consists of 2parts: the seat (A) and Isofix base(B).

06
GENERAL INFORMATION
• This is an Isofix child restraint. It has been approved for general use
in vehicle equipped with Isofix anchoring in compliance with ECE
• It is suitable for use in vehicle with Isofix-approved seats (see
vehicle list) accordance with the relevant child restraint and
anchoring category.
• This child safety restraint is compliant with the Isofix weight
category: up to 18kg and Isofix size categoris: D and B1
manufacturer of the child safety unit or your retailer.
FOR ISOFIX SUITABLE VEHICLES
The AURORA with Isofix system has been approved for
seats.
The appendix VEHICLE LIST contains an overview of vehicles and
vehicle seats that have been approved for using the
Should your vehicle not be listed, please ensure that the
AURORA can be properly mounted in your car / on the desired seat
before you purchase the child seat.
Read the user manual provided by the manufacturer of your vehicle
manual.

07
REMOVING THE SEAT
The seat (A) of AURORA can be removed from the Isofix-Basis (B).
Always remove the child first before removing the seat!
The Locking Handle is located underneath the seat and on the front
top of the Isofix base.
Pull the Locking Handle forwards, as you can see the front lock
unlocks the mental tube on the front of seat.
Unlock the Rear-lock as photo shows, and li the seat up and take it
off from the base.

08
MOUNTING THE AURORA
To make mounng easier, we recommend to mount the Isofix base
first, then to lock the seat to Isofix base.
Always mount and remove the AURORA without a child in it!
Step 1. Mount the Isofix base
Rotate the Isofix system control dial on the front of Isofix base to the
an-clock wise direcon, so you can see the Isofix connector moved
outwards unl it fully extended.
Place the Isofix base in the driving direcon on a vehicle seat
equipped with Isofix anchors.
Push the Isofix connectors towards the Isofix anchors on the vehicle
seat unl you hear a “Click” and see the safety display on both sides
of the Isofix connectors show GREEN.

09
Lock the seat shell to the Isofix base.
Depending on the age of the child, then decide to lock the seat in
rearward posion (Birth to 13kg) or forward posion (9 to 18kg).
CAUTION!
Do not use on seats with airbags. Danger to life!
Always mount the seat without a child in it.
Step 2.1 Locking the seat to the Isofix base in REARWARD POSITION:
Birth-13kg
a) Liing the seat, lock the mental tube in the underneath of the
front side of the to lock into the REAR-LOCK on Isofix base.
b) Pull the LOCKING-HANDLE forward, and push the back edge of the
seat downwards, and lock the mental tube in the underneath of the
rear side of the seat to lock into FRONT-LOCK on Isofix base.
c) Release the LOCKING-HANDLE, and lock the mental tube in the
rear side, make sure you see the Safety display shows GREEN on the
top front side of Isofix base.
pull
click

10
Rotate the Isofix system control dial to the Clockwise direcon unl
the seat close as possible to the back rest of the vehicle’s seat, make
sure the gap has eliminated.
Adjusng the Support Leg.
Push the release buons on both
side to the center direcon, and
extending the support leg to the
surface of floor unl it fully reaches,
make sure you see the safety display
shows GREEN on both side.
CAUTION!
• The seat must be secured with the Isofix system even if there is no
child is travelling.
• Both Isofix connectors must be anchored securely and safety
displays are all show GREEN.
• The seat shell are fully locked on the Isofix base and
safety displays are all show GREEN.
• The support leg must fully reaches
surface of floor and the safety displays
are all show GREEN.

11
Step 2.2 Locking the seat to the Isofix base in
FORWARD POSITION: 9 to 18kg
a) Liing the seat, lock the mental tube in the underneath of the rear
side of the shell to lock into the REAR-LOCK on Isofix base.
b) Pull the LOCKING-HANDLE forward, and push the front edge of the
shell downwards, and lock the mental tube in the underneath of the
front side of the shell to lock into FRONT-LOCK on Isofix base.
c) Release the LOCKING-HANDLE, and lock the mental tube in the
front side, make sure you see the Safety display shows GREEN on the
top front side of Isofix base.
CAUTION!
• Make sure that the seat is correctly anchored to both anchoring
points and the safety display shows GREEN.
• If the child’s body weight exceeds 9kg, the pre-installed pelvis
insert should be removed. (See “Removing the Pelvis Insert”)
• Always mount the seat without a child in it.
click
pull

12
Rotate the Isofix system control dial to the Clockwise direcon unl
the seat close as possible to the back rest of the vehicle’s seat, make
sure the gap has eliminated.
Adjusng the Support Leg.
Push the release buons on both
side to the center direcon, and
extending the support leg to the
surface of floor unl it fully reaches,
make sure you see the safety display
shows GREEN on both side.
CAUTION!
• The seat must be secured with the Isofix system even if there is no
child is travelling.
• Both Isofix connectors must be anchored securely and safety
displays are all show GREEN.
• The seat shell are fully locked on the Isofix base
and safety displays are all show GREEN.
• The support leg must fully reaches surface of
floor and the safety displays are all show GREEN.

13
SECURING YOUR CHILD IN THE AURORA
CAUTION!
Check that the AURORA is mounted properly and that all belts have
proper tension, also that all locking mechanisms are secured and all
safety displays show GREEN.
Adjusng the central device
At the front of the seat under the cover there is
the central adjusng device, which clamps the
central harness ght. Loosen the central
adjusng device by pushing the cap of the
central adjusng device up and pull the harness
forward (do not pull on the harness cushion).
Adjusng the headrest.
Close the both side of the headrest to the
central direcon, at the same me, liing
up or pushing down the headrest at your
required posion.
Placing your child in the seat.
- Open the harness buckle by pushing the red buon, and parng the
buckle tongue to the sides.
- Place your child as far back into the seat as possible, bring the
shoulder/lap harness and central harness in the front of the child and
match the tongue first, then insert into main body of the buckle.
- Pull the central harness on the adjusng device to make sure the
harness secures your child at proper ghtness, by checking with your
two fingers gap between harness and your child’s front shoulder
point. Make sure your child is comfortable and secured.
11
2

14
Checking Point.
- Check that the buckle is fully closed, and none of the harness straps
are twisted.
- Check that the headrest must be adjusted to the size of the child at
proper posion for child’s head.
- Check that the shoulder pad should be located slightly above the
child’s shoulder. The shoulder harness should lie in the middle
between the child’s neck and the outer edge of the shoulder.

15
REMOVING THE AURORA
To make the removal of AURORA easier we recommend you
first remove the seat(A) (See “Remove the Seat”)
Always mount and remove the seat without a child in it!
and move the support leg into its top-most
Rotate the isofix sytem
control dial on the front of
Isofix connectors are released from the
vehicle’s anchoringpoint.

16
USING THE RECLINING ADJUSTMENT
Pull the reclining handle underneath of front seat forward, release
the handle at your required posion unl you hear a “CLICK” to make
sure it’s locked.

17
REMOVING/ATTACHING THE COVER
To remove the cover, the seat shell (A) has to be removed from the
base (B) first. (SEE “Remove the seat”)
1. Loose the harness system by adjusng the central device.
2. Unlock the harness buckle, then take off the Pelvic Insert for new
born to 13kg.
3. First remove the cover from the headrest.
4. Use a pencil-like tool to push the elasc bands buons from top to
downwards direcon, and take off the bands which aached to two
buons on both side on the seat shell.
5. Thread the main buckle body through the buckle pad and out
underneath the cover
6. Loose the elasc bands which are located in the placed marked red
on the reverse side of the cover, and pull the seat off in forward
direcon to take off the main cover.
Check that all the locks are closed and all anchoring are correctly
fastened.
1
2
3
4
4
56

18
REMOVING THE PELVIC INSERT
If the child’s bodyweight exceeds 9kg,
the pre-mounted pelvic insert should
be removed.
CARE INSTRUCTIONS
Light dirt can be easily removed with a damp cloth. The cover can
also be removed and washed at 30’C. Remove the back cushion from
the cover of the head support before you wash it.
The cover material color may run slightly when wet, in parcular
during washing.
Do not use solvents on the cover!

19
REMOVING THE PELVIC INSERT
If the child’s bodyweight exceeds 9kg,
the pre-mounted pelvic insert should
be removed.
CARE INSTRUCTIONS
Light dirt can be easily removed with a damp cloth. The cover can
also be removed and washed at 30’C. Remove the back cushion from
the cover of the head support before you wash it.
The cover material color may run slightly when wet, in parcular
during washing.
Do not use solvents on the cover!
WARRANTY CONDITIONS
The warranty period begins at the me of purchase.
The warranty period granted in compliant with the legal warranty
period in the country of purchase. In terms of content, the warranty
covers rework, replacement delivery, or a rebate as the
manufacturer sees fit.
The warranty applies only for the original user. In case of a fault,
warranty rights will be applicable only if the dealer, where the item
was purchased is nofied immediately aer inial detecon. Should
the dealer be unable to remedy the issue, then the product will be
returned to the manufacturer with a detailed descripon of the fault,
and with the official purchase document including the date of
purchase.
The manufacturer shall not accept liability for faulty products not
delivered by him.
Warranty claims are not valid if:
·the product was modified.
·the product is not returned complete and accompanied by the
original purchase document to dealer within 14 days of the detecon
of the fault.
·the fault occurred due to inappropriate handing or maintenance, or
due to other acons that are the fault of the user, specifically where
the user instrucons were not complied with.
·repairs on the product were carried out by third pares.
·the defect was caused by an accident.
·the serial number has been damaged or removed.
Modificaons to or deterioraon of the product caused by the
contractually agreed use of the item (normal wear and tear) will not
be accepted as a warranty claim.
Any services rendered by the manufacturer in case of a warranty
claim shall not extend the warranty period.