Safety 1st Complete air 65 User manual

4358-7079A 1.9.17
rear facing 5-40 lbs (2.3-18 kg) 19-40 in. (48-101.6 cm)
forward facing 22-65 lbs (10.1-29 kg) 29-49 in. (73.6-125 cm)
and at least 1 year old
2016 Dorel Juvenile.

2
1
E-1 Preparing to Install Rear Facing
E-2 Preparing to Install Lower Anchor Belt Rear Facing
E-3 Installing Rear Facing with Lower Anchor Belt
E-4 Installing Rear Facing with Vehicle Belts
E. Installing Rear Facing.......................Pages 36-43
F. Installing Forward Facing Pages 44-52
F-1 Preparing to Install Forward Facing
F-2 Adjusting Top Anchorage Strap (Tether)
F-3 Preparing to Install Lower Anchor Forward Facing
F-4 Installing Forward Facing with Lower Anchor
F-5 Installing Forward Facing with Vehicle Belts
B. Safety Information........................... Pages 9-10
B-1 Vehicle Seating Position
B-2 Installation in Vehicle
B-3 Child Restraint Use
A. Before You Begin.................................Pages 3-8
A-1 Thank you..
A-2 Registration and Safety Notices
A-3 Understanding Your Child Restraint
C. Basic Use.............................................Pages 11-28
D. General Vehicle Installation.....Pages 29-35
D-1 Vehicle Seating Position
D-2 Choosing Lower Anchor Belt or Vehicle Belts
D-3 Knowing Your Vehicle Belts
D-4 Aircraft Information
C-1 Choosing Position for Your Child
C-2 Preparing Child Restraint to Fit Your Child
C-3 Securing Child in Child Restraint
C-4 Removing Child From Child Restraint
C-5 Reclining Child Restraint
C-6 Removing Harness System
C-7 Removing Pad for Cleaning
C-8 Installing Harness System
C-9 Accessories (on select models)
General Information................................Pages 53-62
Using a Locking Clip
Troubleshooting
Replacement Parts Order Form
Warranty

3
Thank you for choosing this car seat,referred to throughout
this manual as a child restraint.The DJG family is committed
to creating a child restraint with the most comfort and conve-
nience available today.
Remember,parents are a child’s first teachers and examples.
If you always buckle your seat belt,your child will think it is the
natural thing to do.Make it a firm rule that the vehicle does not
go until everyone is buckled up. Make no exceptions.
No one can predict if use of a child restraint will prevent injury
or death in a particular crash.However,combined with careful
driving,proper use of a child restraint can lower a child’s risk of
injury or death in most crashes.
Your child’s safety is worth the time it will take to read and fol-
low these instructions.After reading, if you still have questions
or have any problems with this child restraint,please contact
our Consumer Care Department at:
Dorel Juvenile Group, Inc.
Website: www.djgusa.com
Mailing Address: Dorel Juvenile Group, Inc.
Attn: Consumer Care
P.O. Box 2609
Columbus, IN 47202-2609
Telephone: [phone]
8 A.M. to 6 P.M. EST M-TH
8 A.M. to 4:30 P.M. EST FRI
A-1 ThankYou...
A. Before You Begin
4
Please complete the postage-paid registration card that came
with your child restraint,and send it to us.Child restraints
could be recalled for safety reasons.You must register this
restraint to be reached in a recall.Send your name,address,
email address if available and the restraint’s model number
and manufacturing date to:
Dorel Juvenile Group,Inc.
Consumer Care Department
PO Box 2609
Columbus,IN 47202-2609
or call 1-800-544-1108 or register online at www.djgusa.
com/registration/carseat/us.
For recall information,call the U.S.Government’s Vehicle
Safety Hotline at 1–888–327–4236 (TTY: 1–800–424–
9153),or go to http://www.NHTSA.gov.
If you don’t have the card or if your
address changes, you will find the
model number and manufacture date
on the label located on side of shell.
A-2 RegistrationandSafetyNotices
Model
Number
Manufacture
Date
Example of model number and manufacture date.

PUSH
5
A. Headrest/Harness
Height Adjustment
Levers
B. Adjustable Headrest
C. Upper Harness Slots
D. Cup Holder
(on select models)
E. Harness Release
Lever (under flap)
F. Harness
Adjustment Strap
A-3 UnderstandingYourChildRestraint
continued on next page.
6
A.
B.
C.
G. Chest Clip
H. Harness Strap
I. Buckle Tongue
J. Buckle
K. Lower Harness
Guides
L. Buckle Strap
M. Buckle Strap Slots
E.
F.
G.
I.
K.
L.
H.
J.
D.
Front View Harness System Detail
A. Before You Begin
M.

Rear-Facing
ForChildren 5-22 lbs
(2.3-10kg)
BottomLine MUST Be
Levelwith the
Ground.
Rear-Facing
ForChildre n 22-40lbs (10.1-18 kg)
ANDcan sit up unassisted
MostReclined Level to Ground Line
MostUpright Level to Ground Line
Reclinerange is between
the2 level to ground lines.
Reviewinstruction manual.
4360-2593
Childrestraints could be
recalledfor safety reasons. You
mustregister this child restraint
tobe reached in a recall. Send
yourname, address and the
restraint'smodel number
andmanufacturing date
toDorel Juvenile
Group,Inc.,P. O. Box
2609,Columbus,
IN47202, Attn:
Consumer
Relationsor
registeronline at
www.djgusa.com/registration/
carseats/us. Forrecall
information,call the U.S.
Government'sVehicle Safety
Hotlineat 1-888-327-4236 (TTY:
1-800-424-9153),orgo to
http://www.NHTSA.gov.Forchild
restraintparts and service, call
1-800-544-1108.
Forward-Facing
22-65lbs (10.1-29.4 kg)
34-52inches(85.1-132.1 cm)
Back View
N. Lower Anchor
Hook
O. Top Anchorage
Strap (Tether)
P. Lower Anchor Adjuster
Q. Splitter Plate
R. Recline Stand
S. Instructions
(in recline stand)
T. Top Anchorage
Strap (Tether) Storage
U. Lower Anchor Storage
O.
V. Forward-Facing
Belt Path
W. Rear-Facing Belt
Path
X. Level-to-Ground Lines
(on side of shell)
Q.
T.
S.
V.
W.
Side View
78
R.
T.
R.
U. N.
X.
P.
A. Before You Begin

910
B-3 ChildRestraintUse
Never take your child out of the child
restraint while the vehicle is moving.
Never leave child unattended.
Placing your child in a hot child restraint
may result in burns.
Do not use a child restraint with
damaged or missing parts.
Do not use cut, frayed, or damaged
harnesses.
Do not lubricate buckles and fasteners.
Do not substitute parts or try to modify
the child restraint in any way.
Do not use any child restraint accessory
except those approved by Dorel Juvenile
Group.
Never allow any child to play with this
child restraint; it is not a toy.
Do not remove or cover up any of the
warning labels or other labels on the child
restraint.
Read all instructions for additional
warnings.
On the side of the child restraint there is
a date of manufacture label. Do not use this
child restraint more than 8 years after the
date of manufacture.
B-1 VehicleSeatingPosition
Never place a child rear facing in a
seating position with an active frontal
airbag.
Check the vehicle owner’s manual for more
information about airbag/child restraint use.
For vehicles without a back seat, refer to
your vehicle owner’s manual.
B. Safety Information
B-2 InstallationinVehicle
Check the vehicle belt or lower anchor belt
before each use. Use only if the belt is tightened
properly and securely.
This child restraint should be securely
belted in the vehicle even when not in use. In a
crash or sudden stop, an unsecured child
restraint could injure occupants.
Do not use a child restraint that has been in
a crash. You must get a new child restraint.

C. Basic Use
C-1 ChoosingPositionforYourChild C-2 PreparingChildRestrainttoFit
YourChild
ReleaseChestClip
Press on chest clip
release button and pull
apart.
LoosenHarness
Push down on the
harness release lever
(under flap on the
front of child restraint)
while pulling out on the
harness.
You MUST make these adjustments with your child
before you install the child restraint in the vehicle.
UnbuckleHarness
Press red button. Pull
buckle tongues out. Place
harness straps out of
the way.
continued on next page.
1.
2.
3.
11 12
Place Child in Child
Restraint
Place the child’s bottom
and back flat against the
restraint.
This will allow the harness
to be properly tightened.
4.
5-40 lbs (2.3-18 kg)
and 19-40 in. (48-101.6 cm)
Rear-Facing using 5-point harness
Child and child restraint are placed in the
back seat, facing the back of the vehicle.
22-65 lbs (10.1-29 kg)
and 29-49 in. (73.6-125 cm)
and at least 1 Year Old
Forward-Facing using 5-point harness
Child and child restraint are placed in the
back seat, facing the front of the vehicle.
Your child’s height, weight,and age determine how your child
restraint should be placed in the vehicle.
Please talk to your doctor about the best option for your child.
WARNING: Verify your child’s weight and height (do not
guess) before choosing the child restraint’s placement.
Children up to 1 year of age must ride rear facing.
The American Academy of Pediatrics recommends that children
remain rear facing until they are at least 2 years old.
In this child restraint, your child can remain rear facing up to 40 lb
(18 kg) and up to 40 in. (101.6 cm).
The American Academy of Pediatrics recommends that children
remain in a five-point harness until they outgrow their forward-
facing harnessed child restraint.
This typically occurs around age 4, but some children outgrow
them sooner and others not until later.

Check Buckle
Position
Determine which of the
three slots is closest to the
child and will provide a snug
fit.
5.
13
Rotate metal retainer, then
insert retainer up through
the shell and pad.
From the top, pull buckle
free from shell and pad.
a.
b.
To Change Buckle
Position
Lay the child restraint on its
back and locate buckle’s
metal retainer on bottom of
shell.
6.
You MUST use the 1st or 2nd buckle strap slots
when rear facing. Any slot can be used for forward
facing.
1
2
3
C. Basic Use
14
Insert the buckle’s metal
retainer through the
desired slot.
Make sure that the
buckle is facing out.
From the bottom of
the child restraint, pull
buckle’s metal retainer
completely through
pad and shell.
Pull up on buckle to
make sure it is secured.
The buckle must not
pull out.
Failure to place buckle’s metal retainer
completely through pad and shell can result
in serious injury or death.
c.
d.
e.
continued on next page.

C. Basic Use
ToAdjustHeadrest/
Harness Height
Loosen harness straps.
Rotate headrest/harness
height adjustment levers
inward.
Move headrest to the
proper height and lock
into place.
8.
Make sure metal bar
is locked into position.
Failure to do this can
result in serious injury or
death.
Check Headrest/
Harness Height
With child in the child
restraint, check the location
of the upper harness slots.
Follow the guidelines below
to determine the correct
headrest/harness height.
7.
Rear-FacingPosition
Harness straps MUST be at or
slightly below shoulders.
If the upper harness slots are
above the child’s shoulders
with the headrest in the
lowest position, do not use
this child restraint.
Forward-FacingPosition
Harness straps MUST be at
or slightly above shoulders.
If the upper harness slots are
below the child’s shoulders
with the headrest in the
highest position, do not use
this child restraint.
15 16
Make sure that the harness height is correct for
your child’s size.
Do not use this child restraint rear fac-
ing unless the top of your child’s head
is at least 1 in. (2.5 cm) below the top
of the child restraint’s headrest.
Do not use this child restraint forward
facing if the tops of your child’s ears
are above the top of the child re-
straint’s headrest.
Failure to follow these steps can
result in serious injury or death.

C. Basic Use
C-3 SecuringChildinChildRestraint
Position Harness
Straps Over the
Child’sShoulders
1.
Buckle Harness
Push each buckle tongue
into buckle until you hear a
“click.”
Pull up on harness straps
to make sure buckle is
locked.
2.
Close Chest Clip
Insert right half of chest
clip into left half and
snap together.
3.
TightenHarness
Pull on harness
adjustment strap to
tighten harness snugly.
NOTE: A snug strap
should not allow any
slack. It lies in a relatively
straight line without
sagging. It does not press on the child’s flesh or push the
child’s body into an unnatural position.
Position Chest Clip
The chest clip must be
placed at mid-chest (even
with armpits) and away
from the child’s neck.
6.
17 18
5. Check Harness
Tightness
Try to pinch the harness
at the shoulders. If you
can pinch the harness
strap, tighten more. If
your fingers slip off, the
harness is tight enough.
WARNINGS: Failure to fasten and tighten the
harness system correctly may allow the child to be
ejected from the child restraint in a crash or sudden
stop causing serious injury or death.
Do not mistake comfort for safety. Harness system must
be snugly adjusted.
DO NOT put snowsuits or bulky
garments on your child when
placing them in the child restraint.
Bulky clothing can prevent the
harness straps from being tight-
ened properly.
4.

C. Basic Use
C-4 RemovingChildFromChildRestraint
Loosen Harness
Push down on the harness
release lever (under flap on
the front of child restraint)
while pulling out on the
harness.
1.
ReleaseChestClip
Press on chest clip release
button and pull apart.
2.
UnbuckleHarness
Press red button on buckle
to release the buckle
tongues.
Move harness away from
child and remove child.
3.
19 20
Upright
Rotate recline stand out
and push upward to lock
in position.
ToRecline
Pull recline stand down
and rotate under child
restraint.
C-5 RecliningChildRestraint
RearFacing- 1Must
be fully reclined. Recline
restraint so that the level-
to-ground line on the side
of shell that matches your
child’s weight is level with
ground.
ForwardFacing-2Must
be upright.
1
2

C. Basic Use
21
Rotate metal retainer, then
insert retainer up through
the shell and pad.
From the top, pull buckle
free from shell and pad.
Remove Buckle
Lay the child restraint on its
back and locate buckle’s
metal retainer on bottom of
shell.
3.
a.
b.
22
C-6 RemovingHarnessSystem
Remove Harness
Strap from Splitter
Plate
Fully loosen harness.
Locate splitter plate on
the back of the child
restraint and unfasten the
harness strap.
1.
Remove Harness
Strap
(1) Pull harness strap ends
through the upper harness
slots from the front.
(2) Unthread harness strap
ends from the chest clip.
(3) Unthread harness from
the buckle tongues.
(4) Pull harness strap out of
shell.
2.
1
2
3
4

C. Basic Use
23
Replace child restraint pad by reversing order. Starting from
bottom of child restraint, slip pad on shell. Pull harness
tightening strap through pad. Make sure pad is under
headrest. Replace lower harness guides. Attach all of the
elastic straps. Rethread harness (see section C-8).
Do not use child restraint without the pad.
CleaningPad
If your seat pad has machine washable tag:
Machine wash separately with cold water on a
gentle cycle. Do not use bleach. Tumble dry separately
for 10-12 minutes on low heat. Remove immediately.
If your seat pad does not have machine washable
tag:
Hand wash pad with warm sudsy water, rinse clean and
air dry. Do not use bleach or use other harsh cleaners. Do
not dry clean.
Harness Straps
Spot clean the harness straps.
24
Remove Pad
Adjust backrest to lowest
position. Pull pad off the
top of child restraint and
around headrest.
3.
C-7 RemovingPadforCleaning
You must remove the harness system to remove the pad from
the shell. See section C-6.
Remove theElastic
Straps
Release the elastic
straps on the back of
the child restraint.
1.
2. Remove Harness
Guides
Remove both lower
harness guides (A) in
bottom of child restraint
under recline stand.
Push harness guide lip
toward outside of shell
with one hand while
pulling harness guide
from the front with the
other.
Lower Harness Guides
A
DO NOT remove the headrest pad. Spot clean with warm
sudsy water.

C. Basic Use
a.Take both ends of the
harness strap and make
them even in length.
The sewn ends of the
harness strap loops
MUST face each other
as shown.
b. (3) Thread left harness
strap end through the
back of the left buckle
tongue. Repeat for right
harness strap end.
(4) Thread the chest clip
from front to back as
shown.
(5) Push harness strap
ends through upper
harness slots.
DO NOT twist harness
straps.
34
5
4
2. Thread Harness Strap
(1) With sewn end of
the harness strap loop
facing the buckle,
thread the harness strap
down through lower
harness guide on left side
of shell.
(2) Pull across bottom
of shell and up through
lower harness guide on
right side of shell.
12
continued on next page.
25 26
C-8 InstallingHarnessSystem
Install Buckle
Insert the buckle’s metal
retainer through the desired
slot. Make sure that the
buckle is facing out.
1.
From the bottom of the
child restraint, pull buckle’s
metal retainer completely
through pad and shell.
a.
Pull up on buckle to make
sure it is secured.
The buckle must not
pull out.
b.
Harness adjustment strap
MUST lay between shell and
harness strap as shown.

C. Basic Use
27 28
Thread Harness Strap
OVER Metal Bar
c.
Attach Harness Strap to
Splitter Plate
From the bottom of the child
restraint, fit the harness
strap loops onto the splitter
plate.
Harness strap loop ends
MUST go through the
recline stand as shown.
The sewn ends of the
harness strap loops MUST
face towards you. DO
NOT twist harness straps
or harness adjustment
strap and make sure the
harness strap loops are COMPLETELY ON the splitter
plate.
C-9 Accessories(onselectmodels)
Install Cup Holder
(on select models)
Pull pad off corner. Hook
bottom of cup holder to edge
of shell.
Rotate cup holder up until it
snaps into the hole on the
shell.
Replace pad.
3.
Failure to place the harness
adjustment strap between
shell and the harness straps
as shown can result in
serious injury or death.
Harness MUST be threaded
over the metal bar.
Harness system must be reattached correctly.
Failure to follow these warnings can result in
serious injury or death.

D. General Vehicle Installation
The LATCH System
The lower anchors of LATCH
(LowerAnchors andTethers for
CHildren) is a universal system for
installing child restraints without
using vehicle seat belts.The lower
anchor system can ONLY be used in vehicles that have the
lower anchor bars installed and designated LATCH seat-
ing positions.Most vehicles manufactured after September
2002 are equipped with lower anchor bars.
Check your vehicle owner’s manual to see which seating
positions may be equipped with the LATCH system.
When installing this child restraint with vehicle belts,
the lower anchor hooks and
belt MUST be properly stored.
Storing Lower Anchor Belt
Thread lower anchor belt
through forward-facing belt path.
Then attach hooks to storage
attachment as shown. Gently pull
free end of belt to remove slack.
Lower Anchor Bars
Seat Bight
Your vehicle’s features may be considerably different than
those pictured here.
Lower Anchor Hooks
Adjuster
D-2 ChoosingLowerAnchorBeltor
VehicleBelts
29 30 continued on next page.
D-1VehicleSeatingPosition
Never place a child rear facing in a seating
position with an active frontal air bag.
Check the vehicle owner’s manual for more infor-
mation about air bag/child restraint use.
Use the child restraint only on vehicle seats
that face forward.
Do not use on seats that face the sides or
rear of the vehicle.
Use the center seating position if possible.
For vehicles without a back seat,refer to
your vehicle owner’s manual.
If you are not sure where to place the child restraint in your vehicle,
consult your vehicle owner’s manual,contact Dorel Juvenile Group
Consumer Care Department or visit your local Child Passenger Inspec-
tion Station.Go to http://www.safercar.gov/cpsApp/cps/index.htm to
find your closest station.
Children are safer when properly
restrained in rear seating
positions than in the front
seating positions.
According to National HighwayTraffic SafetyAdministration
information, children in rear seating positions are statisti-
cally safer,whether you have air bags,advanced air bags,or
no air bags at all.
To avoid your child being seriously burned, take the follow-
ing precautions:
1. Park in the shade or where sun does not directly hit the child
restraint.
2. Cover the child restraint with a sheet or blanket when not in use.
3. Check for hot seat and buckles before placing child in child
restraint.
To help protect your vehicle seat’s upholstery from damage, use a
single layer towel underneath and behind child restraint.

31 32
D. General Vehicle Installation
Vehicle Belts
If lower anchors are not an option or if your child weighs
more than 40 lb (18 kg),you must use the vehicle seat belt
system to install the child restraint.
There are some vehicle belts that will not work with a child
restraint or will require special attention.
Check your vehicle owner’s manual for specific instructions.
WARNINGS: When used correctly the lower anchor
belt or vehicle belts are equally safe. Do not use both
the lower anchor belt and vehicle belt at the same time.
Your vehicle’s features may be considerably different than
those pictured here.
1.You MUST Review Your
Vehicle Owner’s Manual
Your vehicle owner’s manual
will let you know what vehicle
belts and seating positions child
restraints can be installed in.
2. Determine How the Child
RestraintWill Be Locked Into
Place
The vehicle belt MUST NOT loosen
after tightening.
This means there needs to be a
way to lock the vehicle belt.
3. Check the Retractor
Retractors pull seat belts into
stored positions and lock the
belt to hold passengers in
place.
A retractor is most likely how
you will be locking a child
restraint into place.
The ways this can be done are:
• By using the seat belt’s retractor; or
• By using the seat belt’s latch plate.
Not all vehicle belts and seating positions will work with
child restraints. Please follow the following steps to under-
stand how to lock a child restraint with a vehicle belt.
See the next page for some common types of vehicle belt
retractors that will work with this child restraint.
D-3 KnowingYourVehicleBelts
continued on next page.

33
D. General Vehicle Installation
34
Switchable Retractor
(most vehicles have this type)
Automatic Locking Retractor
Emergency Locking Retractor
This retractor can be switched to a locking mode.
You MUST have the retractor in the locking mode to use the
seat belt with this child restraint.
Switching to locking mode: Slowly pull the shoulder belt all
the way out,then let it go back in an inch or two.
As it goes back in,you will most likely hear a ratcheting sound.
Gently pull the belt to see if it has locked.You will not be able to
pull any more belt out if the lock has engaged.
This retractor always locks.
It will automatically lock after slowly pulling the seat belt out at least
halfway and letting the belt go back into the retractor an inch or
two.
If the retractor does not lock,it is most likely an Emergency
Locking Retractor.These retractors only lock during a sudden
stop or collision.
You will need to determine if your seat belt’s latch plate can lock
the belt.See Step 4,“Check the Latch Plates,”on next page.
Types of Retractors
See Step 4,“Check the
Latch Plates,” on next
page.
Locking Latch Plate
Emergency Locking
Retractor with a
Sliding Latch Plate
4. Check the Latch Plates
Latch plates are the part of
the seat belt that goes into the
buckle.
Hold the lap belt with one hand
and with your other hand grasp
the tongue of the latch plate
(the part that goes inside the
buckle).Pull the latch plate
straight out in line with the lap
belt.
If the latch plate does not slide
up and down the vehicle belt,it
is a locking latch plate.
If the latch plate slides up and
down the vehicle belt,it is a
sliding latch plate.
Sliding latch plates easily slip
between the lap and shoulder
portions of the belt.
If you have an Emergency
Locking Retractor with a Sliding
Latch Plate,you MUST use a
locking clip to install the child
restraint.See pages 53-58.
Emergency Locking Retractor Lap Only Belt
Inflatable Seat Belts
Never UseWithThis Child Restraint

35 36
E. Installing Rear Facing
Lower Anchor Belt
Lap Belt
Lap/Shoulder Belt
5-40 lbs (2.3-18 kg) and 19-40 in. (48-101.6 cm)
Rear-Facing using 5-point harness
E-1PreparingtoInstallRearFacing
Never install a rear facing child restraint in the
front seat of a vehicle equipped with an active
frontal airbag.
This child restraint MUST always face the rear of
the vehicle when the child is less than 1 year old.
The American Academy of Pediatrics recommends that children
remain rear facing until they are at least 2 years old.
Please talk to your doctor about the best option for your child.
D-4 AircraftInformation
This restraint is certified for aircraft use.
Install the child restraint in a window seat
to avoid blocking the aisle.If the aircraft lap
belt is too short,ask the flight attendant for
a belt extender.
Use only on forward facing aircraft seats.
Contact the airline for their specific policies.
WARNING: Store the lower anchor belt and tether
strap when using the aircraft belts.
Forward FacingAircraft Installation
For forward facing installation follow
section F-5.
Rear FacingAircraft Installation
For rear facing installation follow
section E-4.

37 38
E. Installing Rear Facing
E-2PreparingtoInstallLower
AnchorBeltRearFacing
Pull PadOffCorners of
Child Restraint
Pull the pad off the front
corners of shell.
1.
Routing LowerAnchor
Belt
Insert the hook with adjuster
closest to it through the
rear-facing belt path.
2.
Pull Hook Acrossto
Opposite Side
Lower anchor belt MUST
be under pad and in front of
buckle strap.
NOTE: You must use the 1st
or 2nd buckle strap slots
when rear facing.
3.
Replace Pad Over
Corners
Make sure the lower anchor
belt is not twisted.
4.
PUSH
12
Fold ReclineStand Under
Child Restraint
Store TopAnchorage
Hook (Tether)
Attach the top anchorage
hook (tether) to recline
stand as shown. Tighten
tether to remove the slack.
E-3 InstallingRearFacingwith
LowerAnchorBelt
2.
1.
Place Child Restraint
in the Back Seat Rear
Facing
For children 5-22 lbs
(2.3-10 kg), the bottom
level-to-ground line MUST be
level to the ground.
3.
continued on next page.
Do not use the lower anchor belt along with the vehicle
lap or lap/shoulder belt. Check lower anchor belt before
each use. Use only if the belt can be tightened properly
and securely.
Do not fasten multiple lower anchor hooks on the same
lower anchor bar in the vehicle.
Failure to follow these warnings can result in serious
injury or death.
NOTE: Review your vehicle owner’s manual for lower anchor
belt use.