Sakura GP-CP06 User manual

Dual Action Car Polisher
Instruction Manual
Part no: SS5439
Model: GP-CP06

2
Technical Specification
Important: For your safety, please read the entire instruction manual carefully
and make sure that you fully understand it before you use the equipment. It is
recommended that you keep the manual for future reference.
Important Safety Instructions
Warning: Read all the instructions.
Failure to adhere to the following instructions may lead to electric shocks, fires
and/or serious injury
• Keep the work area clean and well illuminated.
• Do not use in wet or damp conditions e.g. do not use in the rain.
Cable Length 2.8m
RPM 2000-6800
Pad Diameter 125mm
Amps 5.4A
Voltage 240V
Ergonomic
Handle
Speed
Setting
Power
On/Off
Polishing
Pad Supplied with
1x Polisher
1x Polishing Pad
1x Wrench

3
• Do not use power tools in explosive environments, such as in the presence of
flammable liquids, gases or dust.
• Keep children and other bystanders away from the area where you are using
the power tool.
• Wear personal protective equipment as appropriate including safety googles
and a dust mask.
• Stay alert and use common sense when operating this product. Do not use
under the influence of drugs, alcohol or medication.
• Ensure that the plug is correctly fitted to the power socket. Never modify
the plug in anyway. Never use an adaptor plug together with earthed power
tools.
• Never modify this unit in anyway.
• Do not abuse the mains power lead e.g. by pulling, carrying or unplugging
the Polisher.
• When using the Polisher with an extension cable, ensure that you select one
which is fit for purpose.
• Inspect the unit before use.
• After use ensure that the Polisher has finished rotating before placing on a
surface or changing the polishing pad.
• Ensure that the Polisher is turned to ‘off’ before connecting to a mains power
supply.
• Do not use if the Polisher switch does not turn on or off.
• Maintain labels on the Polisher as they contain important safety information.
• Use the Polisher and accessories in accordance with these instructions.
• Regularly clean the air vents.
• Store in a clean, dry location.
• Keep out of reach of children.
• Do not allow people who are unfamiliar with the Polisher or these
instructions to operate.
Saxon accepts no liability for the misuse of this product.

4
Polishing Safety Instructions
This power tool is intended for the purpose of polishing and buffing. Read all
safety warnings, instructions, illustrations, and specifications provided. Failure to
adhere to all of the following instructions can result in electric shock, fire and/or
serious injury.
• Polishing bonnets with drawstrings are not recommended to be used
with this product.
• The rated speed of the accessory must at least correspond to the
maximum rated speed of the Polisher. The accessory MUST be:
• Rated to at least 4,200 RPM
• No larger than 6” (125 mm) in diameter
• Fitted with a threaded opening of 5/8” x 11 TPI
• Undamaged and with a backing pad
• The outer diameter and thickness of the accessory must be within the marked
capacity of your Polisher.
• Do not use a damaged accessory.
• Ensure the mains lead is positioned well away from the rotating accessory.
• Do not use accessories which require liquid coolants.
• The tool will vibrate during use. Avoid using for extended periods of time.
• Do not smoke during use.
• Kickbacks are the result of the Polisher being used incorrectly, on incorrect
objects or with incorrect accessories or under incorrect conditions. It can be
avoided by taking proper precautions.
• Never place your hand near a rotating accessory.
• The warnings, precautions and instructions discussed in this instruction
manual cannot cover all possible conditions and situations which may occur.
It must be understood by the operator that common sense and caution are
factors which cannot be built into this product, but must be applied by the
operator.

5
Using the Polishing Machine
• Make sure that the polishing wheel is securely fastened to the spindle.
• Make sure that the polishing wheel can be turned by hand.
Before use, always ensure that the surface to polish has been thoroughly washed
and is free of dust, dirt, oil and grease.
Place the polish directly onto the pad before turning the Polisher ON
Using the Polisher
• Always hold the Polisher in both hands to start and stop.
• Always start polishing on the lowest speed by setting the regulator to its
minimum setting before turning the unit on.
• Keep the foam pad or polishing bonnet flat against the surface being polished.

6
The Polisher has a variable speed control setting. Always start using the slowest
speed to get the best results.
The polishing pad can be changed as required. Ensure that the Polisher is turned
off at the mains before changing the pad.
The polishing sponge should be centred on the backing pad. The easiest way to do
this is by placing the polishing pad underneath the Polisher and then placing the
backing pad onto it from above. It should be placed evenly around the edge of the
backing pad.
The Polisher normally vibrates during use due to its oscillating action. If the
Polisher vibrates a great deal, check that the polishing sponge is centred on the
backing pad.
The backing pad is factory-balanced for a polishing sponge of the recommended
dimensions.

7
Troubleshooting
Problem Possible Cause Likely Solution
The Polisher
will not start
The power cord is not
plugged in. There is an issue
at the mains power supply.
The Polisher is not turned on
Check the power cord
is plugged in. Check the
power at the mains. If there
is no power, check the
circuit connections
Turn on the polisher
The Polisher
is operating
slowly
Excess pressure has been
applied to the Polisher Decrease pressure applied
Excessive noise
or rattling Internal wear or damage Do not use the machine
Overheated Blocked vents or used
continuously for too long
Allow unit to cool
Clean out the dust from
the vents (whilst power is
disconnected) with a fine
brush or compressed air
The Polisher
does not polish
effectively
The accessory may be worn Replace accessory

Everland Road, Hungerford,
Berkshire, RG17 0DX, UK
01488 689 400
[e-mail]
www.saxon-brands.com
SAKURA® is a registered trademark of
Saxon © 2020 by Saxon
Made in China
Waste electrical products should not be disposed of with household
waste. Please recycle with your local authority or retailer.