Salamander Pumps SKELECT05 ELECT User manual

SKELECT05 ELECT
WARNING! ENSURE PUMP IS ISOLATED FROM
ELECTRICITY AND WATER SUPPLY. IF IN
DOUBT CONSULT A COMPETENT
TRADESMAN.
Pump should be serviced in horizontal
position with couples disconnected and water
and electricity supply isolated.
DO NOT RUN PUMP DRY. ALLOW WATER TO
FILL PUMP TO LUBRICATE SEALS BEFORE
STARTING. CHECK FOR LEAKS DURING TEST
BEFORE BEING SATISFIED PUMP IS OK
PLEASE NOTE:
By using the parts included in this pack to repair your pump, you will
be invalidating any warranty you have on the pump.
Returns:
If you need to return this pack for any reason please ensure the
original packaging and these instructions leaflets are returned also.
If you have any questions or queries regarding this spares pack or
any other pump related questions please contact us.
UK:
Salamander Pumped Shower Systems Limited
Unit 2c, Colima Avenue Enterprise Park West
Sunderland SR5 3XE
Tel: [phone]
Email: [e-mail]
Eire:
MTA agencies Ireland Fearn House,
Unit 4 Jamestown Business Park
Jamestown Road Finglas,
Dublin 11
Tel: [phone]
Email: [e-mail]
Salamander Pumps Shower Systems Limited
Unit 2c Colima Avenue, Enterprise Park West,
Sunderland, SR5 3XE
Telephone: [phone]
Facsimile: 0191 548 4445
Email: [e-mail]
www.salamanderpumps.co.uk
Instructions VIDEOLINK:
Document SSI.10 December15. Issue 1
INTRODUCTION
All positive head FORCE PUMPS
Tools required :
•PZ2 Screwdriver
•7mm Deep Socket
•Long nose Pliers
•Snips
Parts in Service kit:
•Float- PFLOAT02(12) x 2
•NRV- CNRVPL01 (14) x 2
•Hall Effect sensor - EHALLE01 (19) x 2
•Cable Tie- FCABLE01(33) x 2
•Interface -EPCBUN02 (9) x 1
•Screw No:6 x 1/2" (11) X 2

SKELECT05 SERVICE INSTRUCTIONS:
Document SSI.10 December15. Issue 1
11
9
33
20
14
12
21
19
3
6
Mains live (Dark brown)
Mains neutral (Blue)
Hall effect
Motor live(light brown)
Hall effect
Pressure switch
Earth stud
1. Remove NRV(14) from OUTER(3) using long nosed pliers and discard.
2. Remove float(12) noticing its orientation.
3. Repeat above steps for opposite pump side if required.
3. Remove Junction Box (JB) lid screws (11) using PZ2 screwdriver and retain
4. Remove JB lid (6) and retain.
5. Disconnected HE sensor leads and pressure switch connector.
6. Snip cable tie that secures HE sensor to outer (3) note its orientation and remove. Discard both.
7. Repeat above steps for opposite pump side if required.
8. Disconnect mains, motor cables noting their orientation.
9. Remove M4 nut(20) and M4 washer(21) using 7mm deep socket.
10. Remove interface PCB (9)
11. Fit new PCB interface
12. Secure with M4 nut and washer to 1.95Nm +/- 0.15
13. Insert new HE sensor (19) into outer housing and secure with cable tie. Snip excess cable tie off.
14. Insert float (12) into outer in the same orientation as removed ensuring it engages with float guides and
moves freely.
15. Insert new NRV to stop position.
16. Repeat above steps for opposite pump side.
17. Reconnect both HE sensors, Pressure switch and mains, motors cables as per diagram. Ensure cables are
routed via junction box base cable slots.
18. Refit junction box lid checking no cables are trapped.
19. Re-secure JB lid screws to hand tight.
20. Reconnect couplers ensuring filter and rubber washers are seated correctly. Service is now complete and
ready for test.