Salicru Sps.one series User manual

SPS.ONE

UNINTERRUPTIBLE POWER SUPPLY (UPS) SYSTEMS

USER MANUAL

2SALICRU

3

General index

1. INTRODUCTION

1.1. THANK-YOU LETTER

2. SAFETY INFORMATION

2.1. USING THIS MANUAL

2.1.1. Conventions and symbols

3. QUALITY ASSURANCE

AND STANDARDS

3.1. MANAGEMENT STATEMENT

3.2. STANDARDS

3.3. ENVIRONMENT

4. PRESENTATION

4.1. DIAGRAMS

4.1.1. Unit diagrams

4.1.2. Unit diagram key

4.2. CONTENTS

4.3. OPERATING PRINCIPLE

4.3.1. Features

5. INSTALLATION

5.1. STORAGE LOCATION AND CONDITIONS

5.2. CONNECTING THE UNIT TO THE MAINS FOR THE FIRST

TIME OR AFTER IT HAS BEEN OUT OF USE FOR TWO

MONTHS

5.3. CONNECTING THE LOADS

5.4. CONNECTING THE COMMUNICATION CABLE

5.5. DOWNLOADING AND INSTALLING THE SOFTWARE

5.6. STARTING UP/STOPPING THE UNIT

5.6.1. Starting up the SPS.ONE

5.6.2. Stopping the SPS.ONE

6. TROUBLESHOOTING GUIDE

7. GENERAL TECHNICAL

SPECIFICATIONS

USER MANUAL SPS.ONE UNINTERRUPTIBLE POWER SUPPLY (UPS) SYSTEMS

4SALICRU

SALICRU

1. INTRODUCTION

1.1. THANK-YOU LETTER

We would like to thank you for purchasing this product. Read

this instruction manual carefully in order to familiarise yourself

with its contents. You will get the most out of the unit, achieve

a higher the degree of satisfaction and guarantee high levels of

safety the more you understand the unit.

Please do not hesitate to contact us for any further information

or any questions you may have.

Yours sincerely,

•The unit described in this manual can cause serious

physical injury if handled incorrectly. Therefore, the

unit must only be installed, serviced and/or repaired by our

staff or by qualified personnel.

•Although every effort has been made to guarantee that the

information in this user manual is complete and accurate,

we are not responsible for any errors or omissions that may

be present.

The images included in this document are for illustrative

purposes only and may not accurately represent the parts

of the unit shown in this manual. However, any differences

will be reduced or resolved through the correct labelling on

the unit.

•In line with our policy of continuous development, we

reserve the right to modify the specifications, oper-

ating principle or actions described in this document

without prior notice.

•The reproduction, copying, transfer to third parties,

modification or translation in full or in part of this

manual or document, in any form or by any means, without

prior written consent from our company, is prohibited,

with us reserving the full and exclusive right of ownership

to it.

5

2. SAFETY INFORMATION

2.1. USING THIS MANUAL

The user manual is available for customers on our website. It

can be read online or downloaded, as appropriate.

In addition to reading the manual, it is necessary to access

document EK266*08, relating to the "Safety instructions".

Please read these instructions carefully before carrying out any

action on the unit in terms of installation or start-up, change of

location, configuration or handling of any type.

The purpose of the user manual is to provide information re-

lating to safety, as well as explanations about the unit's in-

stallation and operating procedures. Read them carefully and

follow the steps in the corresponding order.

Compliance as regards the "Safety instructions"

is mandatory, with the user being legally respon-

sible for observing and applying them.

All units are supplied with the corresponding labels to guar-

antee the correct identification of each part. In addition, the

user can refer to the user manual at any time during installation

or start-up operation, which provides clear, well-organised and

easy-to-understand information.

Finally, once the unit is installed and in operation, we recom-

mend that you keep the documentation in a safe place that is

easy to access, in case of any future queries that may arise.

The following terms are used interchangeably in the document

to refer to:

•"SPS.ONE, equipment, system, unit or UPS".- SPS.ONE

Uninterruptible Power Supply System.

Depending on the context of the sentence, they may refer

interchangeably to the UPS itself or to the UPS and the bat-

teries.

•"Batteries or capacitor banks".- A group or set of ele-

ments that stores the flow of electrons by electrochemical

means.

•"S.T.S.".- Service and Technical Support.

•"customer, installer, operator or user".- They are used

interchangeably and, by extension, to refer to the installer

and/or the operator who will carry out the corresponding

actions, whereby the responsibility for carrying out the

respective actions may be held by the same person when

they act on behalf or in representation of the installer or

operator.

2.1.1. Conventions and symbols

Some symbols may be used and may appear on the unit, bat-

teries and/or in the user manual.

For more information, see section 1.1.1 of document EK266*08

relating to the "Safety Instructions".

USER MANUAL SPS.ONE UNINTERRUPTIBLE POWER SUPPLY (UPS) SYSTEMS

6SALICRU

3. QUALITY ASSURANCE

AND STANDARDS

3.1. MANAGEMENT STATEMENT

Our aim is to satisfy our customers. Management has estab-

lished a Quality and Environmental Policy for such purposes. As a

result, a Quality and Environmental Management System will be

implemented, which will ensure that we are compliant with the

requirements of the ISO 9001 and ISO 14001 standards and that

we meet all customer and stakeholder requirements.

The company management is also committed to the develop-

ment and improvement of the Quality and Environmental Man-

agement System, through:

•Communication to the entire company of the importance of

satisfaction, both in terms of the customer’s requirements,

as well as legal and regulatory requirements.

•Dissemination of the Quality and Environmental Policy and

setting of the Quality and Environment targets.

•Management reviews.

•Provision of the necessary resources.

3.2. STANDARDS

The SPS.ONE product is designed, manufactured and mar-

keted in accordance with the EN ISO 9001 standard on Quality

Assurance and is certified by SGS. The mark indicates

conformity with the EEC Directives through application of the

following standards:

•2006/95/EC on Low Voltage Safety.

•2004/108/EC on Electromagnetic Compatibility (EMC).

According to the specifications of harmonised standards. Ref-

erence standards:

•EN-IEC 62040-1. Uninterruptible power systems (UPS).

Part 1-1: General and safety requirements for UPS

used in user access areas.

•EN-IEC 60950-1. Information technology equipment.

Safety. Part 1: General requirements.

•EN-IEC 62040-2. Uninterruptible power systems (UPS).

Part 2: Electromagnetic compatibility (EMC) requirements.

The manufacturer shall not be held responsible for any

damage caused by the user after altering or tampering

with the unit in any way.

This product is suitable for use in both single-user pro-

fessional and domestic applications.

The EC declaration of conformity for the product is

available for the customer and can be requested from

our head office.

3.3. ENVIRONMENT

This product has been designed with the protection of the en-

vironment in mind and has been manufactured in accordance

with the ISO 14001 standard.

Recycling the unit at the end of its useful life:

Our company commits to using the services of approved com-

panies that comply with the regulations in order to process the

recovered product at the end of its useful life (please contact

your distributor).

Packaging:

To recycle the packaging, follow the applicable legal regula-

tions, depending on the particular standards of the country

where the unit is installed.

Batteries:

The batteries represent a serious health and environmental

risk. They must be disposed of in accordance with the appli-

cable laws.

7

4. PRESENTATION

4.1. DIAGRAMS

4.1.1. Unit diagrams

Figures 1 to 4 show illustrations of the units, according to the

model. Nevertheless and as the product is continuously being

developed, there may be slight discrepancies or inconsisten-

cies. Therefore, in the case of any queries, the labels on the unit

will always take precedence.

All of the values for the main specifications or features

can be checked on the unit's name plate. Act accord-

ingly for your installation.

SPS.500.ONE, SPS.700.ONE

and SPS.900.ONE

SPS.1100.ONE, SPS.1500.ONE

and SPS.2000.ONE

7

8

9

10

7

8

9

10

Fig. 1. Front views of SPS.ONE.

SPS.1100.ONE SPS.1500.ONE and

SPS.2000.ONE

SPS.500.ONE, SPS.700.ONE

and SPS.900.ONE

1 5 4 3 1 5 3 4 1 5 6 3 4

Fig. 2. Rear views, with Schuko sockets.

USER MANUAL SPS.ONE UNINTERRUPTIBLE POWER SUPPLY (UPS) SYSTEMS

8SALICRU

SPS.1100.ONE SPS.1500.ONE and

SPS.2000.ONE

SPS.500.ONE, SPS.700.ONE

and SPS.900.ONE

1 5 4 3 1 5 4 3 1 5 6 3 4

Fig. 3. Rear views, with British (UK) sockets.

SPS.1100.ONE SPS.1500.ONE and

SPS.2000.ONE

SPS.500.ONE, SPS.700.ONE

and SPS.900.ONE

5 2 4 3 3 4 2 5 3 6 4 2 5

Fig. 4. Rear views, with IEC sockets.

9

4.1.2. Unit diagram key

1. Power cable with pin on end.

2. IEC socket used to power the unit (only in models

without the power supply cable 1).

3. Output sockets.

4. USB HID communication port.

5. Input protection via circuit breaker or fuse, depending

on the model.

6. Fan of the unit (only in models SPS.1500.ONE and

SPS.2000.ONE).

7. Unit start and stop button.

8. Red LED lit. Unit in the Fail-safe Mode. This LED is also

used to warn the user about the fact that the unit charge

level is too low, when it starts to flash, and with the

same modulation as that of the acoustic alarm.

9. Flashing yellow LED. Unit in the Battery Mode - output

power supply from the internal battery-.

10. Green LED on. Unit in the AC Mode - output power supply

from the input voltage-.

4.2. CONTENTS

The following is supplied within the unit's packaging:

•For the models with UK and Schuko sockets:

–SPS.ONE unit.

–Quick guide.

–USB HID communication cable.

•For models with IEC sockets:

–SPS.ONE unit.

–Quick guide.

–USB HID communication cable.

–1 output cable for models 500/700/900 and 2

output cables for models 1100/1500/2000.

4.3. OPERATING PRINCIPLE

•It is an Uninterruptible Power Supply (UPS) system with

line-interactive technology that offers the best protec-

tion solution for the units and the information that make

up both domestic and professional IT environments (small

businesses, offices, shops, etc.).

•The use of AVR Boost&Buck technology - permanent stabi-

lisation of the supply voltage - provides a two-fold advan-

tage: higher protection of connected loads, combined with

a reduced use of UPS batteries.

•In the case of a power supply outage, it supplies electrical

power from the batteries to ensure the units continue op-

erating.

•It is also worth mentioning the built-in communication

functions to communicate between the UPS and computer

system through the USB HID port (communication cable

supplied with the unit) and the monitoring software, com-

patible with Windows, Linux, Unix and Mac.

4.3.1. Features

•Line-interactive technology

•High level of reliability through control by microprocessor

•AVR Boost&Buck permanent stabilisation

•USB HID interface in all models, by default

•Monitoring software for Windows, Linux, Unix and Mac

•A single on/off button for easy and convenient use

•Protection against overloads, short-circuits and transients

•Smart battery charger that reduces the average recharging

time

•Recharging the batteries with the equipment switched off

•Cold start function using the batteries (not connected to the

mains)

•Automatic start-up after the input voltage is reconnected

USER MANUAL SPS.ONE UNINTERRUPTIBLE POWER SUPPLY (UPS) SYSTEMS

10 SALICRU

5. INSTALLATION

•Read and follow the Safety Information set out in

chapter 2 of this document. Failure to adhere to any

of the indications set out in chapter 2 may cause a serious

or very serious accident for those who are in direct contact

with the unit or who are in the vicinity, as well as faults in

the unit and/or in the loads connected to it.

•Check that the information on the name plate is the right

information for the installation.

•Once you have unpacked the unit, inspect it and ensure that it

is in perfect condition before proceeding. If this is not the case,

please contact your distributor.

•Limitations to the connection and use of the unit ac-

cording to its morphology and sector or work envi-

ronment:

For its connection.

–In units with a power supply plug and output

sockets (with no connection terminals).

It can be connected by staff with no specific

technical training; in general, by anyone who

uses household appliances.

For its use.

–Unit with no connection terminals, generally

designed for household environments and, to a

lesser extent, for shops, industry and other sectors.

The unit can be used by staff with no specific

technical training by simply following the in-

structions in the user manual.

•The unit will be connected in all modes with the

switches set to standby and disconnected from the

mains (circuit breaker in the UPS power supply line set to

«Off»), including in the control mode (interface).

•Always bear in mind that the UPS is an electrical gen-

erator, which is why the user must take the necessary

precautions to prevent direct or indirect contact.

5.1. STORAGE LOCATION AND CONDITIONS

•Install the UPS in a protected area that does not have ex-

cessive humidity but has suitable ventilation.

•Place the UPS at a distance of at least 20 cm from other

units to prevent interference.

•Do not operate the unit where the temperature and hu-

midity exceed the permitted limits (see the technical speci-

fications).

20 cm 20 cm

5.2. CONNECTINGTHEUNITTOTHEMAINSFORTHEFIRST

TIME OR AFTER IT HAS BEEN OUT OF USE FOR

TWO MONTHS

•Insert the mains plug 1 into an AC socket.

In models with an IEC socket, a cable is

supplied to power the unit. Insert the end

of the connector into the base 2and the

plug on the other end into the AC socket.

•For the best results, charge the battery

for at least 4 hours before using the unit

for the first time or when it has been out

of use for more than two months.

Otherwise, the SPS.ONE may not react in

a satisfactory way if there is an outage

during the initial operating hours. Its response capacity

during unexpected AC power supply failures is dependent on

the energy accumulated in the battery.

•The battery charges by simply connecting the unit to the

mains.

5.3. CONNECTING THE LOADS

•Connect the loads to the sockets 3on the rear of the unit.

•Never connect a laser printer or

scanner to the UPS. This may

damage the unit and/or consume the en-

ergy stored in the batteries, which is re-

served for other more sensitive and more

important types of loads.

11

5.4. CONNECTING THE COMMUNICATION CABLE

•To enable unattended start-up/stop of the UPS and to mon-

itor its status, connect one end of the communication cable

to the connector 4of the USB HID port of SPS.ONE and the

other end to the communication port of the PC.

•With the monitoring software installed in your PC, you can

programme the UPS start-up/stopping time, as well as

monitor its status in real-time. Follow the steps described

below before downloading and installing the monitoring

software:

5.5. DOWNLOADING AND INSTALLING THE SOFTWARE

•To download the free monitoring software, register as a

user and then register your unit(s) at the following site:

support.salicru.com

•You will find a link to the "ACTIVATION GUIDE"on the reg-

istration page. Follow the steps indicated.

•Once you have registered, you can download the software

for each model from the site:

support.salicru.com/software

•Use with your installation as with any other type of soft-

ware.

•When you reboot your PC, the monitoring software will ap-

pear as an orange icon on the system tray, next to the clock.

5.6. STARTING UP/STOPPING THE UNIT

5.6.1. Starting up the SPS.ONE

•With SPS.ONE stopped, press the button 7to start the unit.

•When the unit is started, an internal test is performed and

all LEDs are turned on. The process takes a few seconds,

after which the UPS will supply an output voltage, either

from the mains or from its batteries.

The auto-test will be performed regardless of whether the

start-up process is carried out with the unit connected to

the mains or running on its batteries (no mains connection).

•Start up the loads.

5.6.2. Stopping the SPS.ONE

•Stopping the loads.

•Switch the unit off, press the button 7.

USER MANUAL SPS.ONE UNINTERRUPTIBLE POWER SUPPLY (UPS) SYSTEMS

12 SALICRU

6. TROUBLESHOOTING GUIDE

Use the following table to resolve minor issues:

Problem Possible cause Solutions

No LED is lit on

the front panel.

Low battery. Charge the UPS for at least 6

hours.

Battery fault. Replace the battery with the

same model.

The UPS is not ON. Press the UPS start-up button

again.

The alarm

sounds

continuously

when connected

to the mains.

The UPS is

overloaded.

First, disconnect a few loads.

Before starting it up again,

check that the connected load

matches the unit's power

specifications.

In the case of

a problem in

the mains, the

operating time

is very short.

The UPS is

overloaded. Disconnect critical loads.

Battery voltage is

too low.

Charge the UPS for at least 6

hours.

Defective battery. It

may be due to the

ambient temperature

or inappropriate

operation.

Replace the battery with the

same model.

There are no

problems in the

mains but the

unit is in battery

mode.

The mains cable plug

is not connected

correctly.

Reconnect the mains cable

plug correctly.

Tabla 1. Troubleshooting table.

•If you are registered on the website:

support.salicru.com

, you can access:

support.salicru.com/troubleshooting

, to consult the extended troubleshooting guide of the unit,

in addition to accessing other services available for regis-

tered users.

13

7. GENERAL TECHNICAL

SPECIFICATIONS

MODEL 500 700 900 1100 1500 2000

Power (VA) 500 700 900 1100 1500 2000

Power (W) 240 360 480 600 900 1200

Technology Line-interactive

INPUT

Voltage 220 / 230 / 240 VAC.

Margins 162-290 VAC.

Nominal

frequency 50 / 60 Hz.

Frequency auto-

detect Yes.

Stabilisation AVR buck/boost.

OUTPUT

Voltage (VAC) 220 / 230 / 240 VAC.

Voltage accuracy(1) ± 10 %.

Frequency(1) 50 / 60 ± 1 Hz.

Waveform(1) Pseudo-sine (simulated sine).

Available socket

types Schuko (DIN), British (UK), IEC.

MODEL 500 700 900 1100 1500 2000

Transfer time standard 2-6 ms, maximum 10 ms.

PROTECTION

Input Thermal self-resetting or fuse (according to the

model).

Complete

protection

Overload, battery discharged and overcurrent in the

charging device.

BATTERY

Type Sealed Pb-Ca, maintenance free, useful life of 3-5 years.

Charge time 4 -6 hours to charge 90% of its capacity.

Battery

replacement

warning

Yes.

Can be replaced by

the user Yes.

Capacity (Ah) 4.5 7 9 7 9

Number 1 2

FUNCTIONS

Cold start Yes.

Auto-test At start-up.

Automatic restart Yes, once the operating time has ended and after

reconnected to the mains.

MODEL 500 700 900 1100 1500 2000

OPTICAL LED INDICATIONS AND ACOUSTIC ALARMS

Normal operation,

connected to the

mains

Green LED On

Alarm Off

Mains error and

UPS in the battery

mode

Yellow LED flashing

Beeping sound every 10 sec.

Low battery Yellow LED flashing. Red LED On

Beeping sound every sec.

UPS stopped Green LED Off

Alarm Off

UPS fault Red LED On

Constant beeping

COMMUNICATION

Port USB HID

Software Supports Windows, Linux, Unix and Mac operating

systems.

Download from support.salicru.com

GENERAL

Maximum altitude 2400 m a.s.l.

Relative humidity Up to 90%, non-condensing.

Temperature 0.. 40ºC.

Acoustic noise at

1 m. < 40 dBA.

STANDARDS

Safety EN-IEC 62040-1, EN-IEC 60950-1.

Electromagnetic

compatibility. (EMC) EN-IEC 62040-2.

Quality and

Environmental

Management

ISO 9001 and ISO 14001.

DIMENSIONS AND WEIGHT

Depth (mm) 300 320

Width (mm) 101 130

Height (mm) 142 182

Net weight (kg) 3.50 4.45 4.90 8.20 10.40 11.00

(1)Battery mode.

Tabla 2. General technical specifications.

USER MANUAL SPS.ONE UNINTERRUPTIBLE POWER SUPPLY (UPS) SYSTEMS

14 SALICRU

: .............................................................................................................................................................................................................

.........................................................................................................................................................................................................................

15

: .............................................................................................................................................................................................................

.........................................................................................................................................................................................................................

USER MANUAL SPS.ONE UNINTERRUPTIBLE POWER SUPPLY (UPS) SYSTEMS

www.linkedin.com/company/salicru

@salicru_SA

Avda. de la Serra 100

08460 Palautordera

BARCELONA

Tel. +34 93 848 24 00

Fax +34 93 848 22 05

[email protected]

SALICRU.COM

Product Range

Uninterruptible Power Supplies (UPS)

Lighting Flow Dimmer-Stabilisers

DC Power Systems

Static Inverters

Photovoltaic Inverters

Voltage stabilisers

The Technical Service and Support (T.S.S.) network, Com-

mercial network and warranty information are available in

website:

www.salicru.com

REF. EK808C01 REV. C CODE 401*

Salicru SPS.ONE Series User manual

Popular UPS manuals by other brands