Salter Brecknell S-100 User manual

Model S-100 Floor Scale
Operation Manual
Manual: xxxxxx Issue:xx

©Avery Weigh-Tronix, LLC. All rights reserved.
The information contained herein is the property of Avery Weigh-Tronix and is supplied without liability for errors or omissions. No part may be
reproduced or used except as authorised by contract or other written permission. The copyright and the foregoing restriction on reproduction
and use extend to all media in which the information may be embodied.
Salter Brecknell is a trading name of Avery Weigh-Tronix LLC
WARNINGS
Safe installation
Safety
THE EQUIPMENT CONTAINS NO USER SERVICEABLE COMPONENTS.
Installation and maintenance of the equipment must only be carried out by trained and authorised
personnel.
Electrical installation
The mains lead must be connected to a supply outlet with a protective earth contact. The electrical supply
at the socket outlet must provide over current protection of an appropriate rating.
For your protection all mains (110V or 230V) equipment used out of doors or in wet or damp conditions
should be supplied from a correctly fused source and protected by an approved ground fault protection
device (RCD, GFCI etc.)
IF IN DOUBT SEEK ADVICE FROM A QUALIFIED ELECTRICIAN.
Routine maintenance
To avoid the possibility of electric shock or damage to the machine, always switch off the machine and
isolate from the power supply before carrying out any routine maintenance.
To avoid the risk of the machine falling, where applicable, ensure that it is placed securely on a flat and
level surface.
Safe use
Caution – Cleaning the indicator/weigh head
Harsh abrasives, solvents, scouring cleaners and alkaline cleaning solutions, such as washing soda,
should not be used especially on the display windows. Under no circumstances should you attempt to
wipe the inside of the machine.
The outside of standard products may be wiped down with a clean cloth, moistened with water containing
a small amount of washing up liquid.
The outside of products waterproofed to IP65, IP66 and IP67 may be washed down with water containing
a small amount of proprietary detergent.
Training
Do not attempt to carry out any procedure on a machine unless you have received the appropriate
training or read the Instruction Manual.
EMC compliance
The following may be applicable to your machine.
WARNING:
This is a class A product. In a domestic environment this product may cause radio interference in which
case the user may be required to take adequate measures.

Contents
WARNINGS............................................................................................................................................................2
Product Identification Table.................................................................................................................................3
ASSEMBLY............................................................................................................................................................4
Product Contents................................................................................................................................................ 4
Setting the Indicator Up for Use.......................................................................................................................... 4
Wire the cable attached to the base as shown (if necessary) ............................................................................. 4
Indicator and Platform Assembly ........................................................................................................................ 5
Display and Keypad............................................................................................................................................ 6
Manual symbols.................................................................................................................................................. 6
Scale Operation.....................................................................................................................................................7
Turning On and Zeroing the Scale...................................................................................................................... 7
Selecting Unit of Measure................................................................................................................................... 7
Using the Tare .................................................................................................................................................... 7
Hold function with automatic zero on next weigh. ............................................................................................... 8
Hold function with manual release. ..................................................................................................................... 8
Removing Hold ................................................................................................................................................... 8
Print Function ..................................................................................................................................................... 8
USER CONFIGURATION SETTINGS....................................................................................................................9
Setup Controls.................................................................................................................................................... 9
Entering setup .................................................................................................................................................... 9
User Configuration Settings ..................................................................................................................................10
RS-232 data commands for SBI protocol.............................................................................................................. 11
Other RS-232 Output Strings............................................................................................................................ 12
RS232 serial interface wiring ............................................................................................................................ 12
Scale calibration .................................................................................................................................................13
Calibration Configuration Settings –.................................................................................................................. 13
Factory Calibration Settings shown in bold ....................................................................................................... 13
Calibration Menu............................................................................................................................................. 14
Service Configuration Settings..........................................................................................................................15
Technical Specifications....................................................................................................................................16
Error Messages..................................................................................................................................................16
Declarations of Compliance...............................................................................................................................17
Contact Information & Technical Support ......................................................................................................... 17
Product Identification Table
Part Number Capacity Region Power Supply (s)
816965001620 75 kg x 0.01kg / 150lb x 0.02lb North America US Version, UL
816965001637 150 kg x 0.02kg / 300lb x 0.05lb North America US Version, UL
816965001644 300 kg x 0.05kg / 600lb x 0.1lb. North America US Version, UL
816965002160 75 kg x 0.01kg / 150lb x 0.02lb. UK/EU 3 pin UK & 3 pin EU
,CE approved
816965002177 150 kg x 0.02kg / 300lb x 0.05lb. UK/EU 3 pin UK & 3 pin EU
,CE approved
816965002184 300 kg x 0.05kg / 600lb x 0.1lb. UK/EU 3 pin UK & 3 pin EU
,CE approved
816965002719 75 kg x 0.01kg / 150lb x 0.02lb. AUS/SA 3-pin Australia C-Tick
approved, 3 pin South
Africa
816965002726 150 kg x 0.02kg / 300lb x 0.05lb. AUS/SA 3-pin Australia C-Tick
approved, 3 pin South
Africa
816965002733 300 kg x 0.05kg / 600lb x 0.1lb. AUS/SA 3-pin Australia C-Tick
approved, 3 pin South
Africa

ASSEMBLY
Product Contents
Setting the Indicator Up for Use
RS232
Loadcell socket
Power/Adapter Socket
Power Supply Connecting the Indicator to the Platform
-
6V DC - 500mA
+
230V - 50Hz
Wire the cable attached to the base as shown (if necessary)
4
2
3
11RED
2RED
3RED
4RED
1. Red Excitation+
2. Black Excitation-
3. Green Signal-
4. White Signal+

Indicator and Platform Assembly
Remove packaging pads
x2
x2
1
2
3
x4
4
5

Display and Keypad
On/Off
UnitsTare
T
kg/lb
kg lb Hold LowBatt CH AC
Max
d =
-
+
SBI 100
Zero
0
NET
Zero
Hold
Print
Function Keys Annunicators
Tare
T
Tare
Zero
0
Weight is zero
On/Off
Zero
On/Off/Zero
kg lb
Unit of measure (Flashing LED means that the
weight reading is not stable.)
Units
kg/lb
Unit of measurement
NET
Tare is activated
Hold
Print
Hold/Print
CH
Battery is charging.
A
C
Adapter is plugged in.
Hold
Hold is activated
Low Batt
-
+
Battery is low.
Manual symbols
Short Key Press
Multiple Key Press Long key press

Scale Operation
Turning On and Zeroing the Scale
On/Off
Zero
ZERO
0
Turning off the scale
On/Off
Zero
Selecting Unit of Measure
Units
kg lb
Using the Tare
1.
2.
3.
NET
4.
NET
Removing the Tare
On/Off
Zero
0
ZERO
kg lb
Tare
NET


Hold function with automatic zero on next weigh.
1.
Hold
Print
Hold
2.
3.
4.
Hold
Hold function with manual release.
This function needs to be setup in Parameter P3.1 shown on page 10
1.
Hold
Print
Hold
2.
3.
Removing Hold
Hold
Print
Hold
Print Function
For communications to a printer or PC, the indicator has to be setup in the following parameters P2, P4, P5 and
P6.



1.
2.
Hold
Print
3. Print
USER CONFIGURATION SETTINGS
Setup Controls
Entering setup
On/Off
Zero
+
Units
Selecting parameter
Tare
Changing data within the parameter
Units
Saving data
Tare
Exiting setup
On/Off
Zero
ZERO
0

Gross: 45.00kg
Tare: 1.35kg
Net: 43.65kg
Hold
Print
kg
Moves flashing digit
Units
Change flashed digits
Tare
kg
Saves data and move down
to next Parameter setting
.
On/Off
Zero
Exits setu
p
mode

User Configuration Settings
Parameter Setting Default settings in bold
P1.xy Auto shutoff timer in minutes
Set up time for the auto off function.
(00 = 0ff, 01-15 = time in minutes)
P1.00
P1.01 – P1.15,
P1.5 = 15 minutes
P2.x
Hold and print key functionality
Setup button function
0 = Press button once to activate hold
1= Press button once to print
2= Press button to print/Press and hold button to activate hold.
P2.0= Hold
P2.1= Print;
P2.2= Print & Hold,
P3.xy
Hold Function Settings
0= No hold function active.
1= Averaging hold with manual push button release.
The weight reading will be held on the display until a higher
weight is applied, this will automatically release the held weight
and re-hold it at the new higher weight reading.
2= Averaging hold with automatic release and re-hold.
A
s above but The weight reading will be held on the display until
the platform is empted and the next weight reading over
10divisions is applied.
3-50= Selectable hold window from +/- 3 to 50 divisions
Will hold display reading once stable within a selectable weight
range, to release the hold button must be represses..
P3.0
P3.1
P3.2
P3.3 to 50
P4.x
RS232 – Serial Interface
Settings for serial interface
0= No RS232 output
1= Print displayed data once stable when print key is pressed;
2= Print gross, tare and net weight once stable when print key is
pressed
3= Continuously output gross weight
4= Continuously output gross, tare and net weight
5= Print displayed data once stable one time only.
6= Print gross, tare and net weight once stable, one time only.
7= Bidirectional - RS232, SBI protocol
P4.0
P4.1
P4.2
P4.3
P4.4
P4.5
P4.6
P4.7
P5.x RS232 Baud rate P5.0= 1200 P5.3= 9600 P5.1= 2400 P5.4= 19200
P5.2= 4800
P6.x
RS232 Data format
0 = 8 digits, no odd or even, 1 start bit, 1 stop bit
1 = 7 digits, 1 even, 1 start bit , 1 stop bit
2 = 7 digits, 1 odd, 1 start bit, 1 stop bit
3 = 8 digits, no parity, 1 start bit, 1 stop bit
P6. 0
P6. 1
P6. 2
P6. 3
P7-P19 .x
SERVICE CONFIGURATIONS ONLY
Any adjustment to these settings could seriously affect the indicators performance.
Seek advice from a service engineer before changing.

RS-232 data commands for SBI protocol
The RS232 can be set so a bidirectional connection can be established between the indicator and the host. To
establish this connection set parameter P4 to 7, and configure setting P5 (baud) and P6 (parity) to host device.
Commands can then be sent from the host to the indicator using the following commands (ensure the letters
entered are in CAPS) (<CR> - Enter)
Command Action Response
W<CR> Takes a reading
Over capacity -
Under capacity -
Zero point error -
Reading (kg or lb)
<LF>^^^^^^^^^u1u2<CR><LF>H1H2H3<CR><ETX>
<LF>_______u1u2<CR><LF>H1H2H3<CR><ETX>
<LF>----------u1u2<CR><LF>H1H2H3<CR><ETX>
<LF><p>w1w2w3w4w5w6<dp>w7u1u2<CR><LF>H1H2H3<CR><ETX>
S<CR> Prints Status Bytes <LF>H1H2H3<CR><ETX>
Z<CR> Zeros the scale <LF>H1H2H3<CR><ETX>
T<CR> Sets up a tare <LF>H1H2H3<CR><ETX>
U<CR> Changes the units <LF>u1u2<CR><LF>H1H2H3<CR><ETX>
L<CR> Activates the hold
function
<LF>H1H2H3<CR><ETX>
X<CR> Switches off the
scale
Indicator switches off.
? Unrecognised
command
<LF>?<CR><ETX>
Key Symbols
<LF> Line feed
<CR> Carriage Return
<ETX> End of text character
<SP> Space
H1H2H3 3 status bytes
<p> Polarity character including minus sign for negative weigh and a space character for positive.
W1-W7 Weight data
<dp> Decimal point
U1U2: Unit measure, kg, lb or oz
Output Status Bit Meaning:
Bit Byte 1 Byte 2 Byte 3
0 0=Stable 0=Not Under
Capacity
00=Not defined
1=Unstable 1=Under Capacity 01=Normal working mode
1 0=Not at zero
point
0=Not over
capacity
10=Hold working mode
1=At zero point 1=Over capacity 11=Not defined
2 Always 0 Always 0 0=Gross Weight
1=Net Weight
3 0=eprom OK
1=eprom error
Always 0 Always 0
4 Always 1 Always 1 Always 1
5 Always 1 Always 1 Always 1
6 Always 0 Always 1 Always 0
7 Parity Parity Parity

Other RS-232 Output Strings
P4-1 = Output Displayed data @ print key :
Format:
<LF>< reading, minus, decimal point, weight unit><CR><EXT>
P4-2 = Output Gross, Tare, Net @ print key
Format:
<LF><Gross: reading, minus, decimal point, unit><CR><EXT>
<LF> <Tare: reading, decimal point, unit><CR><EXT>
<LF> <Net: reading, minus, decimal point, unit><CR><EXT>
RS232 serial interface wiring
DE-9 Female Scale DE-9 Male Host
Pin Name Direction Pin Name Direction
2. TXD Out 2. RXD In
3. RXD In 3. TXD Out
5. SG - 5. Ground -
Pins 1, 4, 6, 7, 8, 9 not used
Example:
xxxxx0.18lb
Example:
Gross:xxxxx0.18lb
Tare:xxxxxx0.18lb
Net:xxxxxxx0.18lb

Scale calibration
Calibration Configuration Settings –
The scale is configured from the factory to match the specified settings for each unit, as defined by the product
specifications and sales brochure. Modification of the setting can be accomplished by altering user configuration
settings P7-P10. Caution: Calibration and/or configuration of calibration settings of your scale should be
accomplished by a trained service technician using certified weights to ensure proper operation and accuracy.
Calibration is not covered under warranty.
Setup Controls
Config
Menu Avail. Settings Default Definition Detailed Setting
P7 00-31 See table 2A Displayed Resolution (00) = 500 (08) = 2400 (15) = 7000
(01 )= 600 (09) = 2500 (16) = 7500
(02 )= 750 (10 )= 3000 (17) = 8000
(03 )= 800 (11) = 3500 (18) = 10,000
(04) =1000 (12 )= 4000 (19) = 12,000
(05 )=1200 (13) = 5000 (20) = 15,000
(06) =1500 (14) = 6000 (21-31) = N/A
(07) = 2000
P8 0,1,2 See table 2a Division Increment 0 = 1 ; 1 = 2 ; 2 = 5
P9 0-5 See table 2a Decimal Position 0 = 123456 ; 1 = 12345.6; 2 = 1234.56 ;
3 = 123.456 ; 4 = 12.3456 ; 5 = 1.23456
P10 0, 1 See table 2a Calibration weight 0 = KG ; 1 = LB
Factory Calibration Settings shown in bold
Primary Capacity Displayed Resolution Units Selectable Capacity P7 P8 P9 P10
150 lb x 0.02 lb 7500 75 kg x 0.01kg 16 1 2 1
150 x 0.05 lb 3000 10 2 2 1
150 x 0.1 lb 1500 06 0 1 1
300 lb x 0.05 lb 6000 150 kg x 0.02kg 14 2 2 1
300 x 0.1 lb 3000 10 0 1 1
300 x 0.2 lb 1500 06 1 1 1
600 lb x 0.1 lb 6000 300 kg x 0.05kg 14 0 1 1
600 x 0.2 lb 3000 10 1 1 1
600 x 0.5 lb 1200 05 2 1 1
75 kg x 0.01 kg 7500 150lb x 0.02lb 16 0 2 0
75 x 0.05 kg 1500 06 2 2 0
75 x 0.1 kg 750 02 0 1 0
150 kg x 0.02kg 7500 300lb x 0.05lb 16 1 2 0
150 x 0.05 kg 3000 10 2 2 0
150 x 0.1 kg 1500 06 0 1 0
300 kg x 0.05kg 6000 600lb x 0.1lb 14 2 2 0
300 x 0.1 kg 3000 10 0 1 0
300 kg x 0.2 kg 1500 06 1 1 0
Table 2a
You may choose to configure your scale for a higher resolution. The factory does not recommend increasing the
resolution above 7,500 divisions for a stable weight reading. Certain environments may cause the scale to be
unstable at factory settings, reduce the # of division settings to increase your stability.
Hold
Print
kg
Moves flashing digit
Units
Change flashed digits
Tare
kg
Saves data and move down
to next Parameter setting
.
On/Off
Zero
Exits setu
p
mode

Calibration Menu
Calibration can be done with 25% to 100% of requested load and can be calibrated with 1 or 2 calibration points
1.
On/Off
Zero
+
Tare
2.
Tare
3.
Tare
4. Enter in calibration weight from 25% to 100% full capacity
25%-100%
kg/lb
5. Single point calibration, enter the same weight in again and move to number 7
For 2 point calibration enter in the second calibration weight between 25% 100% full capacity.
Tare
6.
7
Tare
8.
9.
Tare
ZERO
0
25%-100%
kg/lb
100.00
Hold
Print
Units
Tare
50.00
Hold
Print
Tare
Units
Units
Chan
g
e flashed di
g
its
Tare
kg
Saves data and move down
to next Parameter setting
.
On/Off
Zero
Exits setup mode
Hold
Print
kg
Moves flashing digit

Service Configuration Settings
The scale is configured from the factory to match the specified settings for each unit, as defined by the product
specifications and sales brochure. Modification of the setting can be accomplished by altering user configuration
settings P11-P19. Caution: Configuration of the settings of your scale should be accomplished by a trained
service technician to ensure proper operation and accuracy. Configuration is not covered under warranty.
Setup Controls
Config
Menu Avail. Settings Default Definition Detailed Setting
P11 0,1,2 2 Units key
configuration
0 = KG only ; 1 = LB only ; 2 = units key active KG
and LB
P12 0-7 7 Power On zero
range (full
scale)
0 = +/- 1% ; 1 = +/- 2% ; 2 = +/- 5% ; 3 = +/- 10% ; 4 =
+/- 20% ; 5 = +/- 50% ; 6 = +/- 100% ; 7 = no limitation
P13 00 - 15 3 Zero button
range (Full
scale)
(00) = +/- 1% (06) = +/- 20% (12) = + 5%
(01 )= +/- 2% (07) = +/-no limit (13) = + 10%
(02 )= +/- 3% (08 )= + 1% (14) = + 20%
(03 )= +/- 4% (09) = + 2% (25) = + no limit
(04) =+/- 5% (10 )= + 3%
(05 )= +/- 10% (11) = + 4%
P14 0, 1, 2 0 Signal within
power on zero
point range
0 = current weight ; 1 = calibration zero ; 2 = power off
zero point
P15 0, 1, 2 1 Signal not
within power on
zero point
0 = current weight ; 1 = calibration zero ; 2 = power off
zero point ; 3 = continuously display “0- - - - -“
P16 0-8 6 Zero tracking 0 = 0d AZT off ; 1 = +/- 0.25d, 2 = +/- 0.5d ; 3 = +/- 1d;
4= +/- 1.5d ;5= +/- 2d ;6 = +/- 3d; 7= +/- 4d; 8 = +/- 5d
P17 0-3 2 Data Filter 0 = very weak; 1 = weak; 2 = standard; 3 = strong
P18 0 - 9 1 Weight stability 0 = +/- 0.5d ; 1= +/- 1d; 2= +/- 1.5d ; 3= +/- 2d; 4= +/-
3d ;5= +/- 4d ;6 = +/- 5d; 7= +/- 6d; 8 = +/- 7d; 9 = +/-
8d
P19 0-9 1 Overload range
Full scale
0 = 0% ; 1 = +9d ; 2 = 101% ; 3 = 102% ; 4 = 405% ;
5 = 110% ; 6 = 120% ; 7 = 150%; 8 = 200%; 9 = no
limitation
Hold
Print
kg
Moves flashing digit
Units
Change flashed digits
Tare
kg
Saves data and move down
to next Parameter setting
.
On/Off
Zero
Exits setu
p
mode

Technical Specifications
Scale Indicator
Input signal range: 0mV ～+30mV
Sensitivity: >0.2uV/grad
Internal Resolution: Approximately 520,000 counts
Display Resolution: Can be selected between 500-100,000
System Linearity: Within 0.01% of FS
Loadcell excitation Voltage: +5 VDC (MAX current: 85mA)
Loadcell
Sensitivity: 0.3mV/V --- 3mV/V (must be fit to >0.2uV/display grad.)
Input Resistor: ≥60 Ω
Output Resistor: <10 KΩ
Temperature
Operation:
5oC - 35oC
Storage: 10oC - 70oC
Humidity: ≤95%RH (no condensation)
Power
Battery: 6V4AH lead acid battery, 30 hrs continuous use
When the voltage of battery is below 5.7V, the “Low Bat” annunciator will be lighted, plug in AC adapter to charge
the battery. When “Lo.bAt” and actual weight is displayed alternately, this indicates the voltage of battery is below
5.5V and the scale will be turned off in two minutes automatically.
AC Adapter:
10.5-12VDC 600mA, with central positive, 5.7 VDC -9 VDC
Error Messages
Error Message Definition Required
Solution/Troubleshooting
0¯ ¯ ¯ ¯:
Weight above range for calibrated
zero point.
Remove load before zeroing
Or
Recalibrate the scale.
0_____:
Weight below range for calibrated
zero point.
Remove load before zeroing
Or
Recalibrate the scale.
_____:
Indicates an under range condition Remove all loads and zero the
scale.
¯ ¯ ¯ ¯:
Capacity exceeded Remove the load and try again. If
the load is great than 6 kg a scale
with a larger capacity is required.
CAL-Er: Calibration error Restart calibration
Lo.bAt: Low Battery Recharge the battery. Upon initial
use, it is recommended to charge
battery for 8 hours prior to use.
EEP.E0 EEPROM can’t be accessed Replace S100 Indicator
EEP.E1 Configuration settings have
changed and not been stored
Calibrate the scale to store
settings
EEP.E2 P7-P9 settings exceed scale’s
normal range
Reconfigure P7-P9 setting

Declarations of Compliance
United States
This equipment has been tested and found to comply with the limits for a class A digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference
when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause
harmful interference in which case the user will be required to correct the interference at his own expense.
Canada
This digital apparatus does not exceed the Class A limits for the radio noise emissions from digital apparatus set
out in the Radio Interference Regulations of the Canadian Department of Communications.
Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites applicables aux
appareils numériques de la Classe A prescrites dans le Règlement sur le brouillage radioélectrique edicté par le
ministère des Communications du Canada.
Manufacturer Salter Brecknell
Type S100
Corresponds to the requirements of the following EC directives:-
Electro Magnetic Compatibility Directive:
Low Voltage Directive:
EMC 89/336/EEC
LVD 73/23/EEC
The application harmonised standards are:
EN60950
EN50081-1
EN50082-1
A copy of the original signed declaration for this instrument is available from the UK address below.
Contact Information & Technical Support
UK and Europe
Salter Brecknell Weighing
P.O. Box 9533, Smethwick,
West Midlands, B66 2TE.
United Kingdom.
Tel: [phone]
Fax: [phone]
email:[email protected].uk
www.salterbrecknell.co.uk
USA
Salter Brecknell Weighing Products USA
1000 Armstrong Drive
Fairmont
MN 56031
Toll Free: 800-637-0529
Phone: [phone]
Fax: [phone]
email:[e-mail]
www.salterbrecknell.com
Declaration of Conformity