Salter Brecknell C3225 User manual

C3225
Checkweighing scale
User Guide
MULTI-LINGUAL
76103-555 Issue 0 14.03.2002

C3225 Checkweigher - User guide
©Salter Brecknell Weighing 2002. All rights reserved.
The information contained herein is the property of Salter
Brecknell Weighing and is supplied without liability for errors or
omissions. No part may be reproduced or used except as
authorised by contract or other written permission. The
copyright and the foregoing restriction on reproduction and use
extend to all media in which the information may be embodied.

Table of contents
C3225 Checkweigher - User guide i
Table of contents
Section Page
Warnings 1
Safe installation 1
Safe use 1
Cleaning the machine 1
1 Display and keypad 5
2 Latitude compensation 6
3 Basic operation 7
3.1 Power on/Power off 7
3.2 Weighing 8
3.3 Tare 9
3.4 Check weighing 10
3.5 Setting checkweigh limits 11
4 Main configuration menu 13
4.1 Overview 13
4.2 Navigating the configuration menu 14
4.3 Configuration options 15
4.4 Auto off / Audio beep 25
5 Error displays 29
5.1 Weighing errors 29
5.2 Other errors 29
6 Foot pedal operation 30

Table of contents
ii C3225 Checkweigher - User guide
7 Battery charging 31
Appendix A 33
Latitude compensation maps 33

Warnings
C3225 Checkweigher - User guide 1
Warnings
Safe installation
CAUTION: The mains lead must be connected to a supply
outletwithaprotectiveearth contact.Theelectricalsupplyatthe
socket outlet must provide over current protection of an
appropriate rating.
Pluggable equipment must be installed near an easily
accessible socket outlet. Permanently connected equipment
must have a readily accessible disconnect device incorporated
in the fixed wiring.
For your protection all mains (110V or 230V) equipment used
out of doors or in wet or damp conditions should be supplied
from a correctly fused source and protected by an approved
RCD to BS7071 or BS7288 or BS4293. IF IN DOUBT SEEK
ADVICE FROM A QUALIFIED ELECTRICIAN.
Safe use
To avoid the possibility of electric shock or damage to the
machine, always switch off the machine and isolate from the
power supply before carrying out any routine maintenance.
Cleaning the machine
CAUTION: Harsh abrasives, solvents, scouring cleaners and
alkaline cleaning solutions, such as washing soda, should not
be used especially on the display windows. Under no
circumstances should you attempt to wipe the inside of the
machine.
The outside of standard products may be wiped down with a
clean cloth moistened with water containing a small amount of
washing up liquid. The outside of products waterproofed to
IP65, IP66 and IP67 may be washed down with water
containing a small amount of a proprietary detergent.

Declaration of Conformity
Manufacturer Salter Brecknell
Type C3225
corresponds to the requirements of the following EC directives:
EMC Directive EMC 89/336/EEC
Low Voltage Directive LVD 73/23/EEC
The applicable harmonised
standards are: EN60950, EN50081–1, EN50082–1
A copy of the original signed declaration for this instrument is available
from:
Salter Brecknell Weighing, P.O. Box 9533, Smethwick, West Midlands, B66 2TE

C3225 Checkweigher - User guide 3
Electromagnetic Compatibility Statement for North America
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
providereasonableprotectionagainstharmfulinterferencewhentheequipmentis
operated in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and if not installed and used in accordance with
theinstructionsmanual,maycauseharmfulinterferencetoradiocommunications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user isencouraged totry to correctthe interference byone of the following
measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment to an outlet on a circuit different from that to which the
receiver is connected.
•Consult the dealer or an experienced radio / TV technician for help.

4C3225 Checkweigher - User guide

Display and keypad - 1
C3225 Checkweigher - User guide 5
1 Display and keypad
1. Display
2. Low battery LED
3. Under weight LED
4. Over weight LED
5. Weight in range LED
6. Target Key
7. Tare Key
8. On/off / Zero key
9. Units select key
6
1234 5
789

2 - Latitude compensation
6C3225 Checkweigher - User guide
2 Latitude compensation
The scale automatically compensates for variance in the
earths gravitational pull, at different locations around the
world.
When the scale is powered up for the first time, you are
required to enter a latitude band for your location. The scale
can then compensate accordingly.
At initial power up the scale will show.
1. Press
To cycle through the available zones.
1RWH 6HH·$SSHQGL[$··/DWLWXGH
FRPSHQVDWLRQPDSV·
2. Press to accept.
The scale will then restart.
;,4
Example displays
;,+
;,,
;,+/
33333
22222
+++++
4
....

Basic operation - 3
C3225 Checkweigher - User guide 7
3 Basic operation
3.1 Power on/Power off
To switch the scale ON
To switch the scale OFF
Press and hold for 5 seconds.
1RWH 7KLVIXQFWLRQFDQDOVREHSHUIRUPHGZLWKWKHIRRWVZLWFK
VHH´)RRWSHGDORSHUDWLRQµRQSD H 
33333
22222
+++++
4
....
Example displays

3 - Basic operation
8C3225 Checkweigher - User guide
3.2 Weighing
Basic weighing
1. Switch on the scale.
2. Apply commodity.
3. Take reading.
4. Remove commodity.
Selecting units
Press
To cycle between g, lb and oz.
Zeroing the scale
Press
4
Example displays
+,-./
4

Basic operation - 3
C3225 Checkweigher - User guide 9
3.3 Tare
1. Ensure scale reads zero, press zero if
necessary.
2. Apply container.
3. Press tare.
4. Apply commodity.
5. Take reading.
6. Remove commodity and container.
7. Press tare to cancel.
1RWH 7KLVIXQFWLRQFDQDOVREHSHUIRUPHGZLWKWKHIRRWVZLWFK
VHH´)RRWSHGDORSHUDWLRQµRQSD H 
4
Example displays
+ , -
4
+,-./
;+,-
4

3 - Basic operation
10 C3225 Checkweigher - User guide
3.4 Check weighing
1. Switch on scale. See 3.1 - ’Power on/
Power off’.
2. Press target
To toggle between checkweigh/non
checkweigh modes.
3. If required, apply container and tare. See 3.3 - ’Tare’.
4. Gradually apply commodity, whilst checking LED
indicators.
1RWH ,QDGGLWLRQWRWKHDERYH/('VWKHUHLVDQDXGLEOHWRQHWR
LQGLFDWHZHL KWLQUDQ H
4
Example displays
Weight over limit
Weight under limit
Weight within limits

Basic operation - 3
C3225 Checkweigher - User guide 11
3.5 Setting checkweigh limits
1. Press and hold target.
Set upper limit
2. Press the tare key to cycle through the
display digits, press units to increment the
value.
4444
Example displays
4444
+444
+444
+,44
+,44
+,-4
+,-4
+,-.

3 - Basic operation
12 C3225 Checkweigher - User guide
3. Press target to accept.
4. Set lower check weigh limit in the same way as shown in
steps to 3.
5. The Scale will then return to checkweigh / normal weighing
mode, as appropriate.
1RWH 7KHXQLWVXVHGWRVHWWKHXSSHUDQGORZHUFKHFNZHL K
OLPLWVDUHWKHVDPHDVWKRVHXVHGLQQRUPDOZHL KPRGH6HH
´6HOHFWLQ XQLWVµRQSD H 

Main configuration menu - 4
C3225 Checkweigher - User guide 13
4 Main configuration menu
4.1 Overview
The following options are available from the main
configuration menu:
Function Description Options
CAL Calibration See “CAL - Calibration” on page 15
gGram mode On
Off
oz Ounce mode On
Off
lb Pound mode ON
Off
WT Calibration weight 3kg
6kg
15kg
6lb
12lb
30lb
GRES Gram resolution 0.5
1
2
5
IRES Pound resolution 0.01
0.005
0.002
0.001
DEF Default settings Yes
No
TRADE Sets for legal trade Yes
No
CAP Default capacity 3kg
6kg
15kg

4 - Main configuration menu
14 C3225 Checkweigher - User guide
4.2 Navigating the configuration menu
To access configuration mode
Press and hold for 5 seconds.
To navigate configuration mode
1. Press tare to cycle through functions.
2. Press units to access function.
3. Press tare to cycle through options.
4. Press Target to accept and proceed.

Example displays

6%'
#
(
+,
0
(

Main configuration menu - 4
C3225 Checkweigher - User guide 15
4.3 Configuration options
CAL - Calibration
1. Enter configuration mode.
Press and hold for 5 seconds.
2. Press units key to start calibration
process.
3. Select origin zone.
1RWH 7KHRUL LQ]RQHUHSUHVHQWVWKHODWLWXGH
RIWKHORFDWLRQZKHUHWKHVFDOHLVEHLQ 
FDOLEUDWHG6HH·$SSHQGL[$··/DWLWXGH
FRPSHQVDWLRQPDSV·
4. Press target to accept
1RWH 7KHYDOXHGLVSOD\HGLVWKHFRXQWYDOXH
IURPWKHVFDOH·VORDGFHOO

Example displays
4;,4
4;,+
4;,,
4;,+/
,+,3/

4 - Main configuration menu
16 C3225 Checkweigher - User guide
5. Press zero/on/off.
6. Apply appropriate calibration weight.
7. Press zero/on/off key.
8. Select the d-zone.
1RWH 7KHG]RQHUHSUHVHQWVWKHODWLWXGHRI
WKHORFDWLRQZKHUHWKHVFDOHZLOOEHXVHG
6HH·$SSHQGL[$··/DWLWXGHFRPSHQVDWLRQ
PDSV·,IWKHG]RQHLVQRWNQRZQVHOHFW¶·
7KHG]RQHZLOOWKHQQHHGWREHVHWWKHQH[W
WLPHWKHVFDOHLVVZLWFKHGRQ6HH´/DWLWXGH
FRPSHQVDWLRQµRQSD H 
9. Press target to accept.
The scale will then display as shown for a
few seconds before returning to normal
operation.
4
Example displays
--.2-
;,4
;,+
;,,
;,+/
