Sambo SB DT49M-TD7 User manual

USER MANUAL
SB DT49M-V1 / 201911
SB DT49M-TD7
2 WIRE SYSTEM
7" VIDEO HANDS-FREE COLOR TFT MONITOR
• Please read this manual carefully before using the product you purchase,and keep it well for future
use.
• Please note that images and sketch maps in this manual may be different from the actual product.

PRECAUTIONS
• Slots or openings in the back of the monitor, are provided for ventilation and to ensure reli-
able operation of the video monitor or equipment and to protect if from overheating. These
openings must not be blocked or covered. The monitor should never be placed near or over
a radiator or heat register and should not be placed in a built-in installation such as a book-
case unless proper ventilation is provided.
• All parts should be protected from violence vibration. And not allow be impacting, knocking
and dropping.
• For clean the LCD screen, using hands or wet cloth is forbidden.
• Please do the cleanness with soft cotton cloth, please do not use the organic or chemical
clean impregnate. If necessary, please use pure water or dilute soap water to clean the dust.
• Imagedistortionmayoccurifthevideodoorphoneismountedtooclosetomagneticelde.g.
Microwaves, TV, computer etc.
• Please keep away the video door monitor from wet, high temperature, dust, and caustic and
oxidation gas in order to avoid any unpredictable damage.
• Do NOT open the device in any condition, call the administrator for help if there is any prob-
lem or mulfunction happens.

CONTENTS
PARTS AND FUNCTIONS..................................................................................................... 4
Front panel ............................................................................................................................. 4
Mounting................................................................................................................................. 5
Screen .................................................................................................................................... 6
BASIC OPERATIONS............................................................................................................ 7
Answering a call ..................................................................................................................... 7
Pan-tilt & Zoom....................................................................................................................... 9
Adjusting screen&volume...................................................................................................... 10
Door release.......................................................................................................................... 11
Calling other monitors............................................................................................................ 11
Monitoring.............................................................................................................................. 12
Recording .............................................................................................................................. 13
Viewing images/videos .......................................................................................................... 14
Formating SD card ................................................................................................................ 15
Copying recordings to SD card.............................................................................................. 15
Leaving messages................................................................................................................. 16
Viewing visitor messages ...................................................................................................... 16
Mute function......................................................................................................................... 17
Transferring call..................................................................................................................... 18
Get QR code.......................................................................................................................... 19
Download setup 2 EASY APP ............................................................................................... 19
Get QR code.......................................................................................................................... 19
Surveillance door station via 2 EASY APP............................................................................ 21
Viewing calling records.......................................................................................................... 22
SMS function ......................................................................................................................... 23
Openning staircase light........................................................................................................ 24
Motion detect function .......................................................................................................... 25
SETUP INSTRUCTIONS....................................................................................................... 26
Setting date and time............................................................................................................. 26
Setting ring tone .................................................................................................................... 26
Setting ring volume................................................................................................................ 27
Enabling/Disabling the operation sound................................................................................ 27
Naming door station & camera.............................................................................................. 27
Setting monitor time............................................................................................................... 28
Enabling/Disabling motion detect function ............................................................................ 29
Enabling/Disabling intercom function ................................................................................... 29
Changing the display language ............................................................................................. 30
Restoring to default setting.................................................................................................... 30
SYSTEM CONFIGURATIONS .............................................................................................. 31
Entering installer setup.......................................................................................................... 31
APPENDIX ............................................................................................................................ 35
Specication .......................................................................................................................... 35

-4-
PARTS AND FUNCTIONS
Key functions
[1]
[7]
[6]
[4]
[5]
[2]
[3]
NO. Item Description
[1] Digital LCD touch screen •See the next page for details
•Display the visitors' image
[2] Mute indicator Light up when activate "Mute" function
[3] Home away indicator Light up when activate "Home away" function
[4] Home button
• Press to return main menu page
• Light up in green when power on
• Blink in green when have missed calls or images
have not been viewed.
•Blink in blue while receives call
[5] Microphone Transmit audio from one station to other stations
[6] Speaker Send out sounds of ring tones,audio and alarms
[7] SD card slot Use to insert micro-SD card
Front panel

-5-
The installation height is suggested to 145~160cm.
1. Use screws to fasten the mounting bracket to the wall with mounting box.
2. Connect the 2 wire cables to the unit.
3. Mount the unit to the mounting bracket, make sure the magnet on the unit is absolutely at-
tached to the mounting bracket.
4. Final view.
PARTS AND FUNCTIONS
Terminal description
1 2 3 4
Mounting screw
x 2(included)
Mounting box
(size:86x86mm)
The unit
Magnet
2 wire cable
Mounting bracket
1 2 3 4 5 6
ON DIP
1 2 3 4 5 6
ON DIP
L2
L1
DIP Switches
SW+
SW-
RING
GND
NC
L1,L2: Bus line terminal.
SW+,SW-: Extra door bell call but-
ton connection port.
Ring,GND: Extra buzzer connection
port.
NC: Undened.
DIP switches: Total 6 bits can be
congured.
• Bit1~Bit5: User Code setting.
• Bit6: Set to ON if the monitor is at
the end of the line or works with
DBC4A. Otherwise, set to OFF.
Mounting

-6-
PARTS AND FUNCTIONS
The Main menu is your starting point for using all the applications on your monitor. You can cus-
tomize your Main menu to display your logo.
Press [HOME] button or touch anywhere of the screen on monitor in standby mode, the Main
menu will appear as follow:
Main Menu
CLOSE
Touch it to turn off the screen
and make the monitor in standby
mode.
SETTINGS
Touch it to enter
setup page.
PHONE
Touch it to setup the divert
number if activate the Divert
function.
Displays which door station
is calling.
Shows status of talking,unlocking
ect.
Displays talking time.
5 direction pad button,
zoom&pantilt the picture.
LIGHT
Touch it to light up the
staircase light via RLC.
MOTION DETECT
Touch it to enter motion
detect options.
MONITOR
Touch it to view outdoor condition.
SMS
Touch it to write messages or
review the received/sent out
messages.
MEDIA
Touch it to play recorded images
or videos from door stations.
Review messages left by visitor.
See infos of memory/SD.
CALL RECORD
Touch it to see calling in/calling
out records or missed calls .
CALL SCENARIO
Touch it to activate the functions
of Mute,Left message and Divert
call.
INTERCOM
Touch it to enter
intercom selections.
Current date and time
Status bar
LOGO LOCATION
Touch it to view Device
infos.The logo can be
customized.
While talking with a door station
00:10 DS-1
REC
Note: The 5 direction pad operation should make effective with sh-eye door station.
Blinks while recording.
Screen

-7-
BASIC OPERATIONS
• When there is a call from a video door station.The call tone sounds, an image will be dis-
played on the screen.
• Touch icon on screen, begin communicating hands free with the visitor for 90 seconds.
• While communicating with the visitor, unlock the door, capture images/videos and adjust
screen&volume are available. More details,please refer the following descriptions.
Note: If nobody answers the phone, the screen will be turned off automatically after 40 seconds.
It’s available to select cameras to monitor while being called.
Max.16 cameras can be selected to monitor, 4 cameras is default.
Follow the steps:
Monitoring cameras while being called/talking
00:10 DS-1 00:10 DS-1
Normal
Monitor Select
CM-1
CM-2
CM-3
CM-4
Answering a call

-8-
• Touch icon on screen or press the [HOME] button to complete the communication.
To complete communication
Note: Communication also ends automatically after 90 seconds.
1.Receiving a call while talking with a door station
2.Receiving a call while talking with other monitors
• Other door stations calling is forbidden
• Conclude current talking to answer the new call-in
• The talking will stop immediately, call tone sounds in normal.
• The video image from the door station is displayed on the screen, talking,unlock,capture
images/videos, adjust screen&volume are available.
BASIC OPERATIONS
It’s available to adjust image scale while being called. Total 3 image modes can be selected.
Follow the steps:
Compare the difference of these 3 image modes:
Adjusting image scale while being called/talking
00:10 DS-1 00:10 DS-1
Normal
00:10 DS-1

-9-
BASIC OPERATIONS
It is available to adjust the display mode for viewing images at a fish-eye door station by using
the 5 direction pad button.
Here are some examples:
• Touch icon to zoom the center position.
Note:
1.The zoom&pantilt function should make in effect
sheyedoorstation.
2.The edge of pantilt image will not be displayed.
When an image at a door station is
displayed,move to the desired position
by touching on the
screen to view the image in zoom mode.
• Touch icon to zoom the right position.
Pan-tilt & Zoom

-10-
BASIC OPERATIONS
Adjusting the speaker volume
Adjusting images
While receiving a call from,communicating with, or monitoring a video door station,you can ad-
just the screen and speaker volume. Follow the steps:
Total 4 scene modes can be selected in sequence:Normal, Brightly, Soft and User.Whichever
mode you choose, there will be a corresponding value for contrast,bright and color.
Youshouldknowthatthecontrast,brightandcolorcanbemodiedfreely,butthisactionshould
be at the User scene mode.
Volume can be adjusted at any time.
Adjusting range: 0 (mute), 1 - 9.
Adjust the contrast of the screen,the range is 0~9. Touch -or +to change the level.
Adjust the brightness of the screen ,the range is 0~9. Touch -or +to change the level.
Adjust the color of the screen,the range is 0~9. Touch -or +to change the level.
Touch -or +to reach desired level.
00:10 DS-1 00:10 DS-1
Normal Brightly Soft User
Note: The adjustments have no effect on the recorded images.
Adjusting screen&volume

-11-
BASIC OPERATIONS
Calling monitors in the same room
It is available to release the door during a call-in, communication,or while monitoring a door sta-
tion.
It allows calling between monitors. It is available to call between monitors in the same room or
in the same system,or call the Guard Monitor.Follow the steps to activate the functions:
1. Touch [Inner Broadcase] icon on one of monitor, all other monitors in the same room can
automatically receive messages without answering the call. Note that all other monitors will not
open the screens.
2.Touch [Inner Call] icon on one of monitor, all other monitors in the same room will ring at the
same time,whichever monitor answers the call, conversation is started, other monitors will stop
ringing at once.(Calling ends automatically after 30 seconds if nobody answers the call)
00:10 DS-1
1
Touch either or to release door.
The door lock is released for the set door
release time.
(if two locks are connected to door station,
touch icon to release the second lock)
00:10 DS-1
Inner
Broadcast
Inner Call Name List
Call
Call Guard
Unit
* Use " " or " " to adjust the microphone volume.
* Touch icon to end the calling
* [HOME] indicator will blink all the time until the call is answered.
Door release
Calling other monitors

-12-
BASIC OPERATIONS
Calling other monitors in the same system
Calling the guard monitor
Touch [Name list Call] icon on monitor, the users in the same system will be displayed.
Just select one target, touch icon to call the corresponding user. If the call is
answered,conversation is activated.
A Monitor can be assigned as Guard Unit Monitor; when the Guard Unit Monitor answers the
call, conversation with the guard person is started..
You can monitor the entrance at any time via the monitor.
1.Press the [HOME] button on panel or touch screen in standby mode.
2.Touch [MONITOR] icon on main menu page to enter Monitor select page.
Monitoring door stations/cameras:
• DS1~4 and CAM1~4 can be selected to monitor individually if the system install multi door
stations/cameras.See the following steps:
[ 01 ] Jim. Zhang
[ 02 ] Calo. Liu
[ 03 ] Jacko. Zhang
[ 04 ] Philips. Chen
[ 05 ] Hebe. Zhang
[ 06 ] Tony. Li
Name List
Note:
* Use " <" or " > " to scroll pages.
* Touch " " to rename.
* Touch " " to redial when the icon is on
the screen.
* Calling ends automatically after 30 seconds if
nobody answers the call.
* [HOME] indicator will blink all the time until the
call is answered.
00:10 DS-1
Monitor Select
DS-1
DS-2
DS-3
CAM-1
DS-4
CAM-2
00:10 DS-1
* During monitoring, images can be viewed, but audio cannot be heard.
* If there is a visitor at the entrance, touch icon on screen to begin communication with
door station.
Monitoring

-13-
BASIC OPERATIONS
3.To end monitoring
Touch icon on the screen or press the [HOME] button on the panel.
* Monitoring also ends automatically after 30 seconds.
Video Quard Monitoring:
If the system install multi cameras via QSW. Video quad monitoring is available.
• On Monitor select page, touch “ > “ icon to scroll next page.
• Select “QUARD-1” item to activate video quad monitoring, see the following steps:
Available functions during monitoring(not including video quad monitoring)
•Pantilt&zoom
•Adjustingimages(imagescale/bright/color/contrast)
•Doorrelease
•Volumecontrol
•Manualrecording
Videos and images are possible to be recorded, and both automatic recording and manual re-
cording are available.
00:10 DS-1
REC
Blinks
Automatic recording
• Recording starts after 3 seconds after
receiving a call.
• While recording, “ REC” blinks on the
screen.
• Capture one picture automatically for
each calling.
00:10 DS-1
Monitor Select
CAM-3
CAM-3
CAM-4
CAM-4
CAM-1 CAM-2
QUARD-1
Monitor Select
DS-1
DS-2
DS-3
CAM-1
DS-4
CAM-2
* During monitoring, manual recording is available.
* Touch each one of video to switch to monitor the correcsponding camera Independently.
Recording

-14-
Therecordedimagesarestoredinthebuilt-inmemoryrst.
* Max.118 pictures can be stored in inner memory
* If an micro-SD card is installed, images can be copied to SD card.
* Max. 32G Micro SD card is supported.
Note:
* Automatic recording function cannot be cancelled.
* Automatic recording does not available while monitoring a door station. To save images while monitoring, see manu-
al recording below.
BASIC OPERATIONS
Manual recording
While be called,Touch icon when an image is displayed.
Note:
* Manual recording is available at any time when icon is on the screen.
* Manual recording is allowed in pantilt & zoom mode.
* Manual recording cannot be performed during automatic recording.
The recorded images/videos can be playback on monitor. Follow the steps:
• On main menu page, touch [Media]->[Graphics Playback] icon, most recent recordings are
displayed (If insert an micro SD card,playback videos.Otherwise,playback images).
• Touch " <" or " > " to scroll through recordings(Please note that if the recordings are videos,
touch " " icon to start/pause the videos).
00:10 DS-1
Graphics
Playback
Voice
Prompt
Copy
To SD
Format
SD Card
Visitor
Message
Memo
Information
Video:008/020 2015/06/23 14:36:55
00:03 00:09
* If the monitor installed an micro SD card, the recording format is video, and recording time limited is 10s. The
videos will be saved on micro SD card directly. Otherwise,the recording format is image.
* A brand new SD card needs to be formatted by the monitor, then it can be used for video & audio recording.
To stop
Touch icon on the screen during play.
Press [HOME] button to return to main menu page.
Viewing images/videos

-15-
BASIC OPERATIONS
Micro-SDcardsneedtobeformattedwhenusingtheminthismonitorforthersttime.
* When formatting a micro-SD card, all existing data on card is erased.
* To EXPORT RECORDED IMAGES, refer to following item on this page.
* To VIEW SD CARD INFO, on main menu page, touch Multimedia->Memo information.
Formating a SD card
* When a sound beep beep is sent out and a blue screen is displayed, formatting is complete.
* It may take some time until formatting has been complete.
1.On main menu page,touch Multimedia->Format SD Card. A notice message is displayed.
2. Touch icon to continue formatting. Touch icon to cancel formatting.
When copying is completed, "BKUP_PIC" folder is created on the Micro SD card. Copied im-
agesarestoredwiththefollowinglenames:
Recording Date
Recording Time
Note:
* This action will overwrite all existing images in the "BKUP_PIC" folder on the micro SD card.
* If the number of images or folders exceed the limit of micro SD card, they cannot be copied.
* The images on the micro SD card cannot be copied into the built-in memory.
* If copied is fail, try to format the SD card on the monitor.
20151119_115125.jpg
Copying recordings to SD card
You can copy recordings(videos/images) stored in the built-in memory to a SD card.
• On main menu page, touch [Media]->[Copy to SD], the information of "Copy Pictures To
SD?" will be asked.
• Touch icon to copy. Touch icon to cancel.

-16-
Note:
* The time limited for leaving message is 10s.
* This function will perform immediately if selected,and the Home away indicator " " will be light up at once.
* The status bar on main menu page will show " " icon.
* Touch icon on the screen to exit.
Two modes can be selected.
Leave a Message, Immediately: If you select this mode, when receive calls from door station,
The system will prompt visitor to leave a voice message immediately.
Leave a Message, If No Answer: If you select this mode, door station calls indoor monitor
first, if nobody answer the call within 30 seconds, the system will prompt visitor to leave a
voice message.
BASIC OPERATIONS
This function is very useful when you are away home. Must insert an micro SD card to support
this function.
To activate the function, please follow the steps:
00:10 DS-1
Call Scenario
Normal
Do Not Disturb
Leave a Message,Immediately
Leave a Message,If No Answer
Divert, Simultaneously
Divert, If No Answer
Visitor Message
01/N
06-23 15:22 DS-1
06-18 20:54 DS-1
06-12 11:06 DS-2
05-29 08:39 DS-3
05-27 21:43 DS-1
04-20 13:16 DS-4
All visitor messages from door stations will be recorded and can be reviewed afterwards. To
support this function, the Call Scenario mode should be set to “Leave a Message,Immediately”
or “Leave a Message,If No Answer”. Please refer to the above in detail.
On main menu page, touch [Multimedia]->[Visitor Message] icon, the most recent visitor’s
messages are displayed.
Leaving messages
Viewing visitor messages

-17-
If you don't want to be disturbed,for example,at night. Activating the mute function is necessary
for you.Follow the steps:
00:10 DS-1
Call Scenario
Normal
Do Not Disturb
Leave a Message,Immediately
Leave a Message,If No Answer
Divert, Simultaneously
Divert, If No Answer
Do Not Disturb: If you select this mode, calling from door station or other monitors can not be
made effect.
Note:
* This function will perform immediately if selected,and the Mute indicator " " will be light up at once.
* The status bar on main menu page will show " " icon.
* Touch icon on the screen to exit.
BASIC OPERATIONS
You can review who is visiting at some time.
1. Touch one of the visiting list.
2. Touch icon to show the caller's image.
Visitor Message 01/N
06-23 15:22 DS-1
06-18 20:54 DS-1
06-12 11:06 DS-2
05-29 08:39 DS-3
05-27 21:43 DS-1
04-20 13:16 DS-4
Note:
* Max. 100 messages can be displayed.
* Must insert a SD card to support this function.
Scroll to next page
Delete the selected recording
Playback visitor's video&audio
Scroll to last page
Exit
When touch the
item," >> " icon
will be displayed.
Current page
Total page
Mute function

-18-
BASIC OPERATIONS
2. Divert, If No Answer: If nobody answers the call in 30s when receives call from door sta-
tion, divert the call to the phone.
At this mode, the monitor will shut off the screen after divert successfully, but you can still use it
in normal.
Note:
* The time limited with the phone is 90s.
* The status bar on main menu page will show " " icon.
* Touch icon on the screen to exit.
Available functions during transferring at this mode:
•Pantilt&zoom
•Adjustingimages(imagescale/bright/color/contrast)
•Doorrelease
•Volumecontrol
•Automaticrecording
•Manualrecording
The calling from door station can be diverted to your phone. please note that this function
should be supported by the unit of IPG(V3). Follow the steps to activate this function:
00:10 DS-1
Call Scenario
Normal
Do Not Disturb
Leave a Message,Immediately
Leave a Message,If No Answer
Divert, Simultaneously
Divert, If No Answer
Two modes can be selected.
1. Divert, Simultaneously: When receives call from door station, divert the call to the phone
immediately.
At this mode,the monitor will always open the screen and show image from door station during
diverted, if the monitor answers the call at this time,diverted will conclude at once.
Transferring call

-19-
BASIC OPERATIONS
00:10 DS-1
Get QR code
Press it could
change password
Download setup 2 Easy APP
1. Scan and download 2Easy APP, or search “2Easy” on APP store.
IOS Android
2. Permit “2Easy” with internet access and camera, on monitor, in QR code page , and keep in
QR code page. on 2Easy APP, press on top-right, to scan QR code on monitor, and press “Save”.
00:10 DS-1

-20-
Press here
to disable
3. Disable “IPV6” on 2Easy APP
Most of internet provide doesn’t support IPV6 feature, please manually disable it with follow steps:
BASIC OPERATIONS