Samlex Europe IDC360iM 1224 V 2.0 User manual

IDC360iM 1224 V2.0 - 20211103 EN
IDC360iM 1224 V 2.0
Switch Mode Converter
Galvanic Isolated
360
intelligent
MotionDetect
Owners Manual

IDC360iM 1224 V2.0 - 20211103 EN
Features
IDC360iM 1224 V 2.0
Galvanic isolated input and output
Very low power consumption
Easy installation
Integrated vibration detection
Purpose
The IDC360iM 1224 V 2.0 is an intelligent galvanically isolated inverter that is intended for the correct
charging of a secondary battery system. The IDC360iM 1224 V 2.0 is equipped with voltage detection and
a sensor that can detect vibrations. Based on the measured voltage and /or vibrations, the IDC360iM 1224
V 2.0 can detect whether a vehicle is 'on'.
Installation Wiring diagram
Warnings:
The product must only be connected by skilled
fitters/mechanics who are aware of the
regulations for working with high battery voltages.
The product may be damaged if you use inferior
connection material and/or wiring that is too thin.
A short circuit between the positive and negative
terminals of the battery may cause severe
damage to your system. Always use fuses of the
correct value.
Operation
The IDC has three different modes: Charge, Standby and Off.
After connecting, the converter will be in “Off mode” if the voltage is lower than 12.6V. There is no voltage
on the output and the primary/yellow LED flashes at a frequency of 1Hz. The secondary/green LED is off.
The converter will enter “Charge Mode” if at least one of the following two conditions is met:
• Vibration is detected AND the input voltage is (5sec) above 11.8V.
• There is no vibration AND the input voltage is (5sec) above 12.6V.
The converter delivers 28.8 V at the output in the “Charge mode” and both the primary/yellow and the
secondary/green LED are on.
When a voltage of 28.4 V is measured on the output, a timer will start and runs for an hour. After this hour,
the IDC will be set to the "Standby mode". The IDC output will be 27.4 V in the "Standby mode" and both
the primary/yellow and the secondary/green LED are on.
The IDC will return to the "Charge mode" if:
•The voltage on the output falls below 26.4 V (for 5 s).
•The IDC has been in the "Standby mode" for 24 continuous hours.
The IDC will be set to the "Off mode" from both the "Charge mode" and "Standby mode" if:
• There is vibration AND the input voltage is (5min) below 11.8V.
• There is vibration AND then the input voltage is (10sec) below 11.6V.
• There is no vibration AND then the input voltage is (10min) below 12.4V.
• There is no vibration AND then the input voltage is (3sec) below 12.0V.

IDC360iM 1224 V2.0 - 20211103 EN
Configuring Configuration table
The IDC360iM 1224 can be set on two fronts:
1. The sensitivity.
2. The time the IDC remains switched on after detecting the last
vibration.
When the programming button of the IDC has been pressed for 4
seconds, LED 1 will light up briefly. As soon as this happens, the button
must be released.
The button must again be pressed short to configure the correct
configuration number. The LED will light up as feedback. This means
that configuration #1 has been selected at that moment. If the user
again presses the button short, configuration #2 is selected, etc.
When the button is not pressed for 4 seconds, the LED will again
display the set position. (Example: Configuration #4 has been set by
the user, the LED will flash 4 times.)
* factory setting
Technical details
Input
Output
Supply voltage
12V DC
Voltage
Charge
28,8V DC
Input voltage range
9,0V … 18,0V DC
Rest
27,4V DC
Start-up voltage with vibration
Start-up voltage without vibration
> 11,8V DC ( 5 sec )
> 12,6V DC ( 5sec )
Charge transition
voltage
<26,4V DC
Undervoltage limit with vibration
fast ( 10 sec) <11,6V DC
slow (5 min) <11,8V DC
Charge forcring
every 24 hours
Limite de sous-tension sans
vibration
fast ( 3 sec) <12,0V DC
slow (10 min) <12,4V DC
Stability
±1%
General
Current/fuse
Connections
6 x 6,3mm faston
Current output
±10A
Cabel advice**
2,5 mm2 ~ 6 mm2
Standby current output
±5 mA
h x w x d
80 x 132 x 191mm
Current limit input
±20A
Weight
1317g
Standby current input
±20 mA
Operational temperature
-10°C … +40°C
External fuse output
32V/15A
External fuse input
32V/30A
** depending on cable length, always use fuses
#
Sensitivity
Time
(sec)
1
1 (most sensitive)
1
2
5
3*
30
4
2
1
5
5
6
30
7
3
5
8
30
9
60
10
4
5
11
30
12
60
13
5 (least sensitive)
30
14
60