Samsung AQ07P8GE User manual

ENGLISH
INSTALLATION MANUAL
MANUAL DE INSTALACIÓN
MANUEL D’INSTALLATION
MANUALE D’INSTALLZIONE
MANUAL DE INSTALAÇÃO
INSTALLATIONS-HANDBUCH
E°XEIPI¢IO E°KATA™TA™H™
Split-type Room Air Conditioner (Cool and Heat)
Aire acondicionado doméstico sistema Split (Refrigeración y Calefacción)
Climatiseur de type Séparé(Refroidissement et Chauffage)
Condizionatore d’aria per ambienti ad unitàSeparate (Raffreddamento e Riscaldamento)
Aparelho de ar condicionado tipo Split (Refrigeração e Aquecimento)
Geteilte raumklimaanlage (Kühlen und Wärmen)
¢IAIPOYMENO K§IMATI™TIKO ¢øMATIOY(æ‡ÍË Î·È £¤ÚÌ·ÓÛË)
ESPAÑOL
FRANÇAIS
ITALIANO
PORTUGUÊS
DEUTSCH
E§§HNIKA
E S F I P D G DB98-07972A(7)
AQ07P8GE
AQ07PBGE
AQ07S8GE
AQ07SBGE
SH07ZPG
SH07ZPGA
SH07ZS8
AQ09P8GE
AQ09PBGE
AQ09S8GE
AQ09SBGE
SH09ZPG
SH09ZPGA
SH09ZS8
AQ12PBGE
AQ12SBGE
AQ12PGGB
AQ12PGGE
AQ12SGGB
AQ12SGGE
SH12ZPG
SH12ZPGA
SH12ZSG
Indoor unit
UQ07P8GE
UQ07PBGE
UQ07S8GE
UQ07SBGE
SH07ZPGX
SH07ZPGAX
SH07ZS8X
UQ09P8GE
UQ09PBGE
UQ09S8GE
UQ09SBGE
SH09ZPGX
SH09ZPGAX
SH09ZS8X
UQ12PBGE
UQ12SBGE
UQ12PGGB
UQ12PGGE
UQ12SGGB
UQ12SGGE
SH12ZPGX
SH12ZPGAX
SH12ZSGX
Outdoor unit

E-2
Safety Precautions
◆Do not attempt to install this air conditioner by yourself.
◆Install according to this installation instruction strictly.
◆Install the unit securely in a place which can bear the weight of the unit.
◆Use the attached accessories parts and specified parts for installation.
◆For electrical work, follow the local national wiring standard, regulation.
◆Do not use intermediate connection of the power cord or the extension
cord and do not share the single outlet with other electrical.
◆Check that the refrigerant gas do not leak after installation has
completed.
◆When carrying out piping connection, take care not to let air substances
other than the specified refrigerant go into refrigeration cycle.
WARNING
◆This equipment must be earthed. Do not connect the earth a gas pipe,
water pipe, lighting rod or telephone earth.
◆Do not install the unit in a place where an inflammable gas leaks.
◆Perform the drainage / piping work securely according to the installation
manual.
◆Fasten a flare nut with a torque wrench as specified in this manual.
CAUTION

E-3
ENGLISH
◆PREPARING THE INSTALLATION
■Deciding on Where to Install the Air Conditioner.......................................... 4
■Air Conditioner and Accessories................................................................... 6
◆INSTALLING THE UNIT
■Fixing the Installation Plate........................................................................... 7
■Purging the Unit............................................................................................. 7
■Connecting the Assembly Cable................................................................... 8
■Installing and Connecting the Indoor Unit Drain Hose.................................. 9
■Installing and Connecting the Outdoor Unit Drain Hose............................... 9
■Installing and Connecting the Indoor Unit Assembly Piping ......................... 10
■Cutting/Extending the Piping ........................................................................ 11
◆COMPLETING THE INSTALLATION
■Connecting Up and Purging the Circuit......................................................... 12
■Performing Leak Tests................................................................................... 13
■Placing the Indoor Unit in Position................................................................ 13
■Fixing the Outdoor Unit in Position ............................................................... 14
■Checking and Testing Operations ................................................................. 14
■Explaining Operations to the Owner ............................................................. 15
◆TECHNICAL SPECIFICATIONS
Contents

E-4
Deciding on Where to Install the Air Conditioner
When deciding on the location of the air conditioner with the owner, the following restrictions
must be taken into account.
General
Do NOT install the air conditioner in a location where it will come into contact with the following elements:
◆Combustible gases
◆Saline air
◆Machine oil
◆Sulphide gas
◆Special environmental conditions
If you must install the unit in such conditions, first consult your dealer.
Indoor Unit
◆There must be no obstacles near the air inlet and outlet.
◆Install the indoor unit on a surface that can support its weight.
◆Choose a position that enables the piping and cables to be easily connected to the outdoor unit and the
recommended length of 5 metres to be respected (15 metres maximum).
◆Leave enough clearance beneath the indoor unit to enable the filters to be removed without hindrance.
◆Maintain sufficient clearance around the indoor unit, as indicated in the diagram on the page opposite.
◆Make sure that the water dripping from the drain hose runs away correctly and safely.
◆Install the indoor unit on the wall which is far from the floor by more than 2.5meters.
Outdoor Unit
◆The outdoor unit must NEVER be placed on its side or upside down, as the compressor lubrication oil will run into the
cooling circuit and seriously damage the unit.
◆Choose a location that is dry and sunny, but not exposed to direct sunlight or strong winds.
◆Do not block any passageways or thoroughfares.
◆Choose a location where the noise of the air conditioner when running and the discharged air do not disturb any
neighbours.
◆Choose a position that enables the piping and cables to be easily connected to the indoor unit and the recommended
length of 5 metres to be respected (15 metres maximum).
◆Install the outdoor unit on a flat, stable surface that can support its weight and does not generate any unnecessary
noise and vibration.
◆Position the outdoor unit so that the air flow is directed towards the outside, as indicated by the arrows on the top of
the unit.
◆Maintain sufficient clearance around the outdoor unit, as indicated in the diagram on the page opposite.
◆If the outdoor unit is installed at a height, ensure that its base is firmly fixed in position; the maximum height is
7metres.
◆Make sure that the water dripping from the drain hose runs away correctly and safely.
◆You have just purchased a split-type room air conditioner and it has been installed by
your installation specialist.
◆This device must be installed according to the national electrical rules.
◆Max input power & current is measured according to IEC standard and input power &
current is measured according to ISO standard.
CC
CCAA AAUU UUTT TTII IIOO OONN NN
PREPARING THE INSTALLATION

E-5
ENGLISH
PREPARING THE INSTALLATION
125 mm
or more
300 mm or more
125 mm
or more
600 mm
minimum
300 mm
minimum
300 mm
minimum
600 mm
minimum
15metres
maximum
✴ The appearance of the unit may be different from the diagram depending on the model.
Respect the clearances and maximum lengths indicated in the diagram below when installing the unit.
Wrap the refrigerant pipes and the drain
hose up in the absorbent pad and the
vinyl tape, refer to page 13.
7metres maximum

E-6
Air Conditioner and Accessories
The following accessories are supplied with the air conditioner.
➢The quantities are indicated in parentheses.
Accessories in the Indoor Unit Case
OWNER'SINSTRUCTIONS
MANUALDEINSTRUCCIONES
ISTRUZIONIPERL'USO
MANUALDEINSTRUÇÕES
MANUELD'UTILISATION
GEBRAUCHSANWEISUNG
Splut-typeRoomAirConditioner
AireacondicionadodomésticosistemaSplit
Condizionatored'ariaperambientiadunitàSeparate
AparelhodearcondicionadotipoSplit
Climatiseurdetypeséparé
Geteilteraumklimaanlage
OWNER'SINSTRUCTIONS
MANUALDEINSTRUCCIONES
ISTRUZIONIPERL'USO
MANUALDEINSTRUÇÕES
MANUELD'UTILISATION
GEBRAUCHSANWEISUNG
Splut-typeRoomAirConditioner
AireacondicionadodomésticosistemaSplit
Condizionatored'ariaperambientiadunitàSeparate
AparelhodearcondicionadotipoSplit
Climatiseurdetypeséparé
Geteilteraumklimaanlage
Accessories in the Outdoor Unit Case
➢The flare nuts are attached to the end of each evaporator in/out pipe or service valve.
Use the nuts when connecting the pipe.
➢The 5-wire assembly cable is depending on the option. If they are not supplied, Using the standard
cable.
➢The drain plug and rubber leg are only included when the air conditioner is supplied without the
assembly piping illustrated below.
The following connection accessories may be supplied, depending on the option. If they are not supplied,
it is recommended that you collect them together before starting to install the air conditioner.
➢If these accessories are supplied, they are located in the accessory box.
Installation Plate (1) Remote Control (1)
Rubber Leg (4)
Batteries for
Remote Control (2) Owner’s Instruction Booklet (1) Installation Manual (1)
PREPARING THE INSTALLATION
Pipe Clamps B (3) M3.8 x 20 Screws
for Wood (10) Putty 100g (1)M4 x 16 Tapped Screws (10) Drain Hose, length 2m (1)
Pipe Clamps A (3)
Assembly Piping,
Ø6.35mm by 5m (1) Assembly Piping,
Ø9.52mm by 5m (1)
(✴✴07/09✴✴)
Assembly Piping,
Ø12.70mm by 5m (1)
(✴✴12✴✴)
PE T3 Foam Tube
Insulation (1)
Vinyl Tape,
Width 50mm (1) Drain Plug (1) Rubber LEG (4)
Drain Plug (1)
5-wire
Assembly Cable (1)

E-7
ENGLISH
Fixing the Installation Plate
Purging the Unit
Before fixing the installation plate to a wall or window frame, you
must determine the position of the 65 mm hole through which the
cable, piping and hose pass to connect the indoor unit up to the
outdoor unit. When facing the air conditioner in position on the wall,
the piping and cable can be connected from the:
◆Right
◆Left
◆Rear (right or left)
1Determine the position of the pipe and drain hose hole using the right
figure and drill the hole with an inner diameter of 65 mm so that it slants
slightly downwards.
2 If you are fixing the indoor unit to a... Then follow Steps...
Wall 3.
Window frame 4to 6.
3Fix the installation plate to the wall in a manner appropriate to the weight
of the indoor unit.
➢If you are mounting the plate on a concrete wall with anchor
bolts, the anchor bolts must not project by more than 20 mm.
4Determine the positions of the wooden uprights to be attached to the
window frame.
5Attach the wooden uprights to the window frame in a manner appropriate
to the weight of the indoor unit.
6Using tapped screws, attach the installation plate to the wooden uprights,
as illustrated in the last figure opposite.
INSTALLING THE UNIT
19
100 158
30mm
Installation plate
Pipe hole
(
Ø 65mm)
(Unit : mm)
✴✴07/09✴✴
On delivery, the indoor unit is loaded with an inert gas. All this gas
must therefore be purged before connecting the assembly piping.
To purge the inert gas, proceed as follows.
Unscrew the caps at the end of each pipe.
Result: All inert gas escapes from the indoor unit.
➢To prevent dirt or foreign objects from getting into the pipes
during installation, do NOT remove the caps completely
until you are ready to connect the piping.
45
90 165
(Unit : mm)
✴✴12✴✴

E-8
Connecting the Assembly Cable
The outdoor unit is powered from the indoor unit via the assembly cable.
If the outdoor unit is more than five metres away from the indoor unit,
the cable must first be extended to a maximum of 15 metres.
1Extend the assembly cable if necessary.
2Open the front grille by pulling on the tabs on the lower right and left sides of
the indoor unit.
3Remove the screw securing the connector cover.
4Pass the assembly cable through the rear of the indoor unit and connect the
assembly cable to terminals as shown in the figure.
➢Each wire is labeled with the corresponding terminal number.
5Pass the other end of the cable through the 65 mm hole in the wall.
6Replace the connector cover, carefully tightening the screw.
7Close the front grille.
8Remove the terminal board cover on the side of the outdoor unit.
9Connect the cables to terminals as shown in the figure.
➢Each wire is labeled with the corresponding terminal number.
10 Connect the earth wires to the earth terminals.
11 Replace the terminal board cover, carefully tightening the screw.
12 Connect the power cable with the indoor unit.
INSTALLING THE UNIT
N1 1 2
N1 1 2 3
3
E231
N1
E
231
1
N1N1
N1
Indoor
unit
Outdoor
unit
❊ The designs and shape are subject to
change according to the model.
Power cable specification
◆ Connect the power cable to the auxiliary circuit breaker.
An all pole disconnection from the power supply must be incorporated in the fixed
wiring(≥3mm).
✴✴✴07/09/12✴✴✴
AC 220-240V,
50HZ
3G, 1.0mm2,
10/16A
H05VV-F
5G, 1.0mm2
H07RN-F
Power plug with
earth pole.
(More than 10A)
Model
Power
supply Power cable
Interconnection
cable
Power plug or
circuit breaker

E-9
ENGLISH
To install the drain hose, proceed as follows.
1If necessary, connect the 2-metre extension to the drain hose.
2If you are using the extension, insulate the inside part of the extension
drain hose with a shield.
3Pass the drain hose under the refrigerant piping, taking care to keep the
drain hose tight.
4Pass the drain hose through the hole in the wall, making sure that it is
sloping downwards, as shown in the illustrations above.
➢The hose will be fixed permanently into position once the
whole installation has been tested for gas leaks; refer to
page 12 for further details.
Installing and Connecting the Indoor Unit Drain Hose
Installing and Connecting the Outdoor Unit Drain Hose
Care must be taken when installing the drain hose for the indoor unit to ensure that any condensation
water is correctly drained outside. When passing the drain hose through the 65 mm hole drilled in the
wall, check that none of the following situations occur.
The hose must
NOT slope
upwards.
The end of the drain
hose must NOT be
placed in water.
Do NOT bend the
hose in different
directions.
Keep a clearance of
at least 5 cm between
the end of the hose
and the ground.
Do NOT place the
end of the drain hose
in a hollow.
5 cm
less Ditch
Shield
Drain hose Extension drain hose
INSTALLING THE UNIT
When using the air conditioner in the heating mode, ice may
accumulate. During de-icing, the condensed water must be drained
off safely. Consequently, you must install a drain hose on the outdoor
unit, following the instructions below.
1Insert the drain plug into the drain hole on the underside of the outdoor
unit.
2Connect the drain hose to the drain plug.
3Ensure that the drained water runs off correctly and safely.
Drain hole

E-10
There are two refrigerant pipes of different diameters:
◆A smaller one for the liquid refrigerant
◆A larger one for the gas refrigerant
A short length of piping is already fitted to the air conditioner. You must
extend this piping using assembly piping (optionally supplied).
The connection procedure for the refrigerant piping varies according to the
exit position of the piping from the indoor unit, as seen when facing the air
conditioner in position on the wall:
◆Right (A)
◆Left (B)
◆Rear
1With a knife, cut out the appropriate knock-out piece on the rear of the
indoor unit (unless you are connecting directly from the rear).
2Smooth the cut edges.
3Remove the protection caps on the pipes and connect the assembly piping
to each pipe, tightening the nuts, first manually and then with a wrench,
applying the following torque.
Outer Diameter Torque (kg•cm)
6.35 mm 144~176
9.52 mm 333~407
12.70 mm 504~616
➢If the piping must be shortened or extended, refer to page 11.
4Cut off any excess foam insulation.
5If necessary, bend the pipe round, along the bottom of the indoor unit and
out through the appropriate hole, taking care to ensure that:
◆The piping does not jut out from the rear of the indoor unit
◆The bending radius is 100 mm or more
6Pass the piping through the hole in the wall.
7For further details on how to connect up to the outdoor unit and purge the
circuit, refer to page 12.
➢The piping will be insulated and fixed permanently into position
once the whole installation has been tested for gas leaks;
refer to page 13 for further details.
Installing and Connecting the Indoor Unit Assembly Piping
INSTALLING THE UNIT
A
B