Samsung GD17N User manual

TFT-LCD MONITOR
GD17N*/GD17A*
Manual
SERVICE
TFT-LCD MONITOR CONTENTS
CHMenuExitPIP
Source
TVV2V1PC VOL
SyncMaster 150MP
1. Precautions
2. Product Specifications
3. Disassembly & Reassembly
4. Alignment & Adjustments
5. Troubleshooting
6. Exploded View & Parts List
7. Electrical Parts List
8. Block Diagram
9. Wiring Diagram
10. Schematic Diagrams
11. Panel Description
CONFIDENTIAL

1-1-1 Warnings
1. For continued safety, do not attempt to modify the
circuit board.
2. Disconnect the AC power and DC Power Jack
before servicing.
1-1-2 Servicing the LCD Monitor
1. When servicing the LCD Monitor Disconnect the
AC line cord from the AC outlet.
2. It is essential that service technicians have an
accurate voltage meter available at all times. Check
the calibration of this meter periodically.
1-1-3 Fire and Shock Hazard
Before returning the monitor to the user, perform the
following safety checks:
1. Inspect each lead dress to make certain that the
leads are not pinched or that hardware is not
lodged between the chassis and other metal parts in
the monitor.
2. Inspect all protective devices such as nonmetallic
control knobs, insulating materials, cabinet backs,
adjustment and compartment covers or shields,
isolation resistor-capacitor networks, mechanical
insulators, etc.
3. Leakage Current Hot Check (Figure 1-1):
WARNING: Do not use an isolation transformer during
this test.
Use a leakage current tester or a metering system
that complies with American National Standards
Institute (ANSI C101.1, Leakage Current for
Appliances), and Underwriters Laboratories (UL
Publication UL1410, 59.7).
Figure 1-1. Leakage Current Test Circuit
4. With the unit completely reassembled, plug the AC
line cord directly into a 120V AC outlet. With the
unit’s AC switch first in the ON position and then
OFF, measure the current between a known earth
ground (metal water pipe, conduit, etc.) and all
exposed metal parts, including: metal cabinets,
screwheads and control shafts. The current
measured should not exceed 0.5 milliamp. Reverse
the power-plug prongs in the AC outlet and repeat
the test.
1-1-4 Product Safety Notices
Some electrical and mechanical parts have special
safety-related characteristics which are often not
evident from visual inspection. The protection they give
may not be obtained by replacing them with
components rated for higher voltage, wattage, etc. Parts
that have special safety characteristics are identified by
on schematics and parts lists. A substitute
replacement that does not have the same safety
characteristics as the recommended replacement part
might create shock, fire and / or other hazards. Product
safety is under review continuously and new
instructions are issued whenever appropriate.
GD17N*/GD17A* 1-1
CONFIDENTIAL
1 Precautions
Follow these safety, servicing and ESD precautions to prevent damage and to protect against potential hazards such as
electrical shock.
1-1 Safety Precautions
DEVICE
UNDER
TEST
TEST ALL
EXPOSED METAL
SURFACES
(READING SHOULD
NOT BE ABOVE 0.5mA)
LEAKAGE
CURRENT
TESTER
2-WIRE CORD
ALSO TEST WITH
PLUG REVERSED
(USING AC ADAPTER
PLUG AS REQUIRED) EARTH
GROUND
!

1-2-1 General Servicing Precautions
1. Always unplug the unit’s AC power cord from the
AC power source and disconnect the DC Power
Jack before attempting to:
(a) remove or reinstall any component or assembly,
(b) disconnect PCB plugs or connectors, (c) connect
a test component in parallel with an electrolytic
capacitor.
2. Some components are raised above the printed
circuit board for safety. An insulation tube or tape
is sometimes used. The internal wiring is
sometimes clamped to prevent contact with
thermally hot components. Reinstall all such
elements to their original position.
3. After servicing, always check that the screws,
components and wiring have been correctly
reinstalled. Make sure that the area around the
serviced part has not been damaged.
1. Immediately before handling any semiconductor
components or assemblies, drain the electrostatic
charge from your body by touching a known earth
ground. Alternatively, wear a discharging wrist-
strap device. To avoid a shock hazard, be sure to
remove the wrist strap before applying power to
the monitor.
2. After removing an ESD-equipped assembly, place it
on a conductive surface such as aluminum foil to
prevent accumulation of an electrostatic charge.
3. Do not use freon-propelled chemicals. These can
generate electrical charges sufficient to damage
ESDs.
4. Use only a grounded-tip soldering iron to solder or
desolder ESDs.
5. Use only an anti-static solder removal device. Some
solder removal devices not classified as “anti-static”
can generate electrical charges sufficient to damage
ESDs.
4. Check the insulation between the blades of the AC
plug and accessible conductive parts (examples:
metal panels, input terminals and earphone jacks).
5. Insulation Checking Procedure: Disconnect the
power cord from the AC source and turn the power
switch ON. Connect an insulation resistance meter
(500 V) to the blades of the AC plug.
The insulation resistance between each blade of the
AC plug and accessible conductive parts (see
above) should be greater than 1 megohm.
6. Always connect a test instrument’s ground lead to
the instrument chassis ground before connecting
the positive lead; always remove the instrument’s
ground lead last.
6. Do not remove a replacement ESD from its
protective package until you are ready to install it.
Most replacement ESDs are packaged with leads
that are electrically shorted together by conductive
foam, aluminum foil or other conductive materials.
7. Immediately before removing the protective
material from the leads of a replacement ESD,
touch the protective material to the chassis or
circuit assembly into which the device will be
installed.
Caution: Be sure no power is applied to the
chassis or circuit and observe all
other safety precautions.
8. Minimize body motions when handling
unpackaged replacement ESDs. Motions such as
brushing clothes together, or lifting your foot from
a carpeted floor can generate enough static
electricity to damage an ESD.
1 Precautions
1-2 GD17N*/GD17A*
CONFIDENTIAL
1-3 Electrostatically Sensitive Devices (ESD) Precautions
Some semiconductor (solid state) devices can be easily damaged by static electricity. Such components are commonly
called Electrostatically Sensitive Devices (ESD). Examples of typical ESD devices are integrated circuits and some field-
effect transistors. The following techniques will reduce the incidence of component damage caused by static electricity.
1-2 Servicing Precautions
WARNING: An electrolytic capacitor installed with the wrong polarity might explode.
Caution: Before servicing units covered by this service manual, read and follow the Safety Precautions
section of this manual.
Note: If unforeseen circumstances create conflict between the following servicing precautions and any of the
safety precautions, always follow the safety precautions.

CONFIDENTIAL
2 Product Specifications
2-1 Specifications
LCD Panel TFT-LCD panel, RGB vertical stripe, normaly white, 17-Inch viewable,
0.269 mm pixel pitch
Scanning Frequency Horizontal : 30 kHz ~ 80 kHz (Automatic)
Vertical : 56 Hz ~ 75 Hz (Automatic)
Display Colors 16,7 Million colors
Maximum Resolution Horizontal : 1280 Pixels
Vertical : 1024 Pixels
Input Video Signal Analog, 0.7 Vp-p ± 5% positive at 75 Ω, internally terminated
Input Sync Signal Type: Seperate H/V automatic synchronization
without external switch of sync type
Level: TTL level
Maximum Pixel Clock rate 135 MHz
Active Display 337.9 mm / 270.3 mm
Horizontal/Vertical
AC power voltage & Frequency AC 90 ~ 264 Volts, 60/ 50 Hz ± 3 Hz
Power Consumption 49 W (max)
Dimensions
Unit (W x D x H) 17.6 x 6.0 x 17.2 Inches (448 x 153 x 438 mm)
Carton (W x D x H) 21.0 x 7.4 x 23.3 Inches (533 x 189 x 593 mm)
Weight (Net/Gross) 6.2 kg (13.7 Ibs) / 8.7 kg (19.2 Ibs)
GD17N* GD17A*
TV System Tunning Frequency Synthesize Frequency Synthesize
Color NTSC PAL, SECAM
Sound BTSC.A2 STEREO.FM-FM NICAM.A2 STEREO
Antena Input 75ΩCoaxial Cable
– MAX Internal speaker Out : Right => 1.5 W
Left => 1.5 W
– BASS Control Range : -12 dB ~ + 12 dB
– TREBLE Control Range : -12 dB ~ + 12 dB
Sound Characteristic – Line Out : -7 dBm (Fixed)
– Headphone Out : RF => 5 mW (400 m Vrms)
A/V => 10 mW (580 Vrms), Max Input sound : -9 dB
– Output Frequency : RF => 80 Hz ~ 15 KHz (at -3 dB)
A/V => 80 Hz ~ 20 KHz (at -3 dB)
• GD17N*/GD17A* comply with SWEDAC (MPR II) recommendations for reduced electromagnetic fields.
• Designs and specifications are subject to change without prior notice.
GD17N*/GD17A* 2-1
Item Description

CONFIDENTIAL
2 Product Specifications
2-2 GD17N*/GD17A*
2-2 Pin Assignments
Sync
Type
Pin No.
15-Pin Signal Cable Connector
Separate Composite Sync-on-green
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Red
Green
Blue
GND
GND (DDC Return)
GND-Red
GND-Green
GND-Blue
No Connection
GND-Sync/Self Test
GND
DDC Data
Horizontal sync
Vertical sync
DDC Clock
Red
Green
Blue
GND
GND (DDC Return)
GND-Red
GND-Green
GND-Blue
No Connection
GND-Sync/Self Test
GND
DDC Data
H/V-Sync
Not Used
DDC Clock
Red
Green + H/V Sync
Blue
GND
GND (DDC Return)
GND-Red
GND-Green
GND-Blue
Not Used
GND-Sync/Self Test
GND
DDC Data
Not Used
Not Used
DDC Clock

CONFIDENTIAL
2 Product Specifications
GD17N*/GD17A* 2-3
QRS
P
O
Video
Sync Sync
Horizontal Vertical
CDE
P
O
B
A
Video
Sync Sync
Separate Sync
2-3 Timing Chart
This section of the service manual describes the timing that the computer industry recognizes as standard
for computer-generated video signals.
C D
AO
E
BP
Video
Sync Sync
Video
Q R S
A : Line time total B : Horizontal sync width O : Frame time total P : Vertical sync width
C : Back porch D : Active time Q : Back porch R : Active time
E : Front porch S : Front porch
VIDEO
A
BO
P
QRS
Horizontal Vertical
B
Green Vertical
PQRS
O
Horizontal
H/V Composite Sync
Sync-on-Green
79.976
12.504
1.067
1.837
9.481
0.119
75.025
13.329
0.038
0.475
12.804
0.013
135.000
Positive
Positive
Separate
81.129
16.640
6.400
2.880
3.200
76.106
10.660
0.080
3.200
0.020
135.000
Negative
Negative
Com.
68.677
14.561
1.016
2.201
10.836
0.508
84.997
11.765
0.044
0.524
11.183
0.015
94.500
Positive
Positive
Separate
1024/85Hz
1024x768 1280/76Hz 1280x1024 1280/75Hz 1280x1024
1024/75Hz
1024 x 768
60.023
16.660
1.219
2.235
13.003
0.203
75.029
13.328
0.050
0.466
12.795
0.017
78.750
Positive
Positive
Separate
31.469
31.777
3.813
1.589
26.058
0.318
70.087
14.268
0.064
0.858
13.155
0.191
28.322
Negative
Positive
Separate
fH (kHz)
A µsec
B µsec
C µsec
D µsec
E µsec
fV (Hz)
O msec
P msec
Q msec
R msec
S msec
Clock
Freq.
(MHz)
Polarity
H.Sync
V.Sync
Remark
IBM
640/75 Hz
640 x 480 640/85 Hz 640 x 480 800/75 Hz 800 x 600 800/85 Hz 800 x 600 1024/60Hz 1024 x 768
VGA2/
70 Hz
720 x 400
VGA3/
60 Hz
640 x 480
Table 2-1 Timing Chart
31.469
31.778
3.813
1.589
26.058
0.318
59.940
16.683
0.064
0.794
15.761
0.064
25.175
Negative
Negative
Separate
37.500
26.667
2.032
3.810
20.317
0.508
75.000
13.333
0.080
0.427
12.800
0.027
31.500
Negative
Negative
Separate
43.269
23.111
1.556
2.222
17.778
1.556
85.008
11.764
0.671
0.578
11.093
0.023
49.500
Negative
Negative
Separate
46.875
21.333
1.616
3.232
16.162
0.323
75.000
13.333
0.064
0.448
12.800
0.021
49.500
Positive
Positive
Separate
53.674
18.631
1.138
2.702
14.222
0.569
85.061
11.756
0.056
0.503
11.179
0.019
56.250
Positive
Positive
Separate
48.363
20.677
2.092
2.462
15.754
0.369
60.004
16.666
0.124
0.600
15.880
0.062
75.000
Negative
Negative
Separate
Mode VESA
Timing (Analog Only) (Analog Only)

Memo
2 Product Specifications
2-4 GD17N*/GD17A*
CONFIDENTIAL

GD17N*/GD17A* 3-1
CONFIDENTIAL
3 Disassembly and Reassembly
This section of the service manual describes the disassembly and reassembly procedures for the
GD17N*/GD17A* monitors.
WARNING: This monitor contains electrostatically sensitive devices. Use caution when handling
these components.
3-1 Disassembly
Cautions:1. Disconnect the monitor from the power source before disassembly.
2. Follow these directions carefully; never use metal instruments to pry apart the cabinet.
1. Remove the 2 screws at each bottom of the
set.
2. Remove the 5 screws on the rear cover.
3. Put the jig into the bottom right between
cover rear and cover front tilt up the front
cover until the snap opens.
4. Pull up the rear cover to remove it
completely from the cover front.

3 Disassembly and Reassembly
3-2 GD17N*/GD17A*
CONFIDENTIAL
3-2 Reassembly
Reassembly procedures are in the reverse order of Disassembly procedures.

CONFIDENTIAL
GD17N*/GD17A* 4-1
4 Alignments and Adjustments
4-1 General Alignment Instuction
1. Usually, a color TV-VCR needs only slight touch-up adjustment upon installation.
Check the basic characteristics such as height, horizontal and vertical sync.
2. Use the specified test equipment or its equivalent.
3. Correct impedance matching is essential.
4. Avoid overload. Excessive signal from a sweep generator might overload the front-end
of the TV. When inserting signal markers,do not allow the marker generator to distort
test result.
5. Connect the TV only to an DC power source with voltage and frequency as specified on
the backcover nameplate.
6. Do not attempt to connect or disconnect any wire while the TV is turned on. Make sure
that the power cord is disconnected before replacing any parts.
7. To protect aganist shock hazard,use an isolation transform.

Memo
4 Alignments and Adjustments
4-2 GD17N*/GD17A*
CONFIDENTIAL

CONFIDENTIAL
GD17N*/GD17A* 5-1
5 Troubleshooting
5-1 No Power
Does proper DC 14 V appear at
DC jack connected to CN101? Check SMPS PCB and Adapter.
Yes
No
Does proper DC 5 V
appear at Pin 4 of IC101? Check IC101.
Check IC201.
Yes
No
Does proper DC 2.5 V appear at
Pin 2, 4 of IC109, IC104? Check IC109, IC104.
Yes
No
Does proper DC 3.3 V
appear at Pin 3 of IC103? Check IC103.
Yes
No

CONFIDENTIAL
5 Troubleshooting
5-2 GD17N*/GD17A*
5-2 No Video (PC Signal)
Power indicator is green.
Does the signal appear at
R132, R133, R134? Check R132, R133, R134, R137, R138,
R139, R103, R104, R105.
Yes
No
Does the clock pulse
appear at R357? Check related circuit of IC301, FT301.
Yes
No
Does the clock pulse appear at
output of RA306 ~ RA311? Check related circuit of IC301.
Yes
No
Does the clock pulse
appear at Pin 12 of IC204? Check IC204 and related circuit of IC204.
Yes
No
Does the clock pulse appear at
output Pin 39, 40 of IC403? Replace IC403.
Replace LCD Panel.
Yes
No

CONFIDENTIAL
5 Troubleshooting
GD17N*/GD17A* 5-3
5-3 No Picture (TV, Video 1, Video 2)
Check Pin 8 (AGC)
of IC703 (CN402). Check replace the tuner.
Yes
No
Check Pin 52, 53, 55, 56 of IC402. Replace IC402.
Yes
No
Does the signal appear at D405. Check related circuit of
D405 and replace D405.
Yes
No
Check Q401 and replace mainboard.

5 Troubleshooting
5-4 GD17N*/GD17A*
CONFIDENTIAL
Does the low signal
at R528, R529? Check related circuit of
R528, R529 and replace.
Yes
No
Check Pin 14, 17
of IC502 (TDA7496). Replace IC502.
Yes
No
Check Pin 60, 67 of
IC501 (MSP25/10). Replace IC501 (MSP25/10).
Yes
No
Check related circuit of
IC501, IC502 and tuner.
5-4 No Sound

CONFIDENTIAL
GD17N*/GD17A* 6-1
6 Exploded View and Parts List

Memo
6 Exploded View & Parts List
6-2 GD17N*/GD17A*
CONFIDENTIAL

CONFIDENTIAL
- BN94-00311A ASSY PCB MAIN GD17NS SNA
C103 2409-001044 C-ORGANIC 100UF,+-20%,16V,WT,TP,8X10.5,5
C104 2409-001044 C-ORGANIC 100UF,+-20%,16V,WT,TP,8X10.5,5
C150 2409-001044 C-ORGANIC 100UF,+-20%,16V,WT,TP,8X10.5,5
C502 2401-001363 C-AL 470uF,20%,16V,GP,TP,10x12.5,5
C503 2401-001363 C-AL 470uF,20%,16V,GP,TP,10x12.5,5
C504 2401-001363 C-AL 470uF,20%,16V,GP,TP,10x12.5,5
CIS1 BN70-00022A BRACKET HINGE-LEFT GD15NS,SHIELD D/SUB SNA
CIS2 0201-001223 ADHESIVE-TS HT-130S,RED,700+/- 50,- SNA
CIS3 0202-001044 SOLDER-WIRE. S63S-W3.0,S63S,D3,63Sn/37Pb,- SNA
CIS4 0202-001046 SOLDER-WIRE FLUX CF-110VH-2A,-,-,-,- SNA
CIS5 0202-001162 SOLDER-CREAM RMA-20-21L,S63,-,SN63/PB36.6/AG0.4,FLUX9.5% SNA
CIS6 0202-001222 SOLDER-WIRE FLUX RS-107,RS60-1.2AA,D1.2,SN60/PB40,- SNA
CIS7 0204-001095 THINNER #4520,-,-,- SNA
CN101 3722-000117 JACK-DC POWER 3P,3.5mm,AG,BLK,NO SNA
CN102 3701-001219 CONNECTOR-DSUB 15P,3R,FEMALE,ANGLE,AUF
CN201 3711-000057 CONNECTOR-HEADER BOX,3P,1R,2.5mm,ANGLE,SN SNA
CN202 3711-002000 CONNECTOR-HEADER BOX,18P,2R,2mm,STRAIGHT,SN
CN401 3722-001031 JACK-PIN 3P,3.6mm,#18,AU
CN402 BH40-00004A TUNER
TCLN9081PA27D,-,NTSC,181CH,45.75MHZ,-,-,-,F-CON,ASYMM,5V,TR,-,-,-,-,-,-,-,-,-
CN403 3722-001100 JACK-DIN 4P/2C,6mm,AG,BLK,NO SNA
CN501 3722-001055 JACK-PHONE 5P/2C,3.6PI,AG,BLK,#16-22 SNA
CN502 3722-000143 JACK-PHONE 1P(VER),3.4PI,AG,BLK,NO
CN503 3711-004386 CONNECTOR-HEADER BOX,3P,1R,2mm,ANGLE,SN SNA
CN504 3711-004270 CONNECTOR-HEADER BOX,2P,1R,2MM,ANGLE,SN SNA
L401 2701-000146 INDUCTOR-AXIAL 2.2uH,10%,2.5x3.4mm
L402 2701-000114 INDUCTOR-AXIAL 10uH,10%,2.5x3.4mm
L403 2701-000114 INDUCTOR-AXIAL 10uH,10%,2.5x3.4mm
L404 2701-000157 INDUCTOR-AXIAL 220uH,5%,2.5x3.4mm
L405 2701-000210 INDUCTOR-AXIAL 680uH,10%,3x7mm
L408 2701-000146 INDUCTOR-AXIAL 2.2uH,10%,2.5x3.4mm
L409 2701-000146 INDUCTOR-AXIAL 2.2uH,10%,2.5x3.4mm
L410 2701-000146 INDUCTOR-AXIAL 2.2uH,10%,2.5x3.4mm
CIS BN97-00096N ASSY MICOM GD17NS
IC203 1102-001097 IC-EPROM
27C010,128KX8BIT,PLCC,32P,-,90NS,5V,10%,PLASTIC,0TO+70C,0.1MA,CMOS,TR
CIS BN46-00012N MICOM-S/W GD17NS SNA
- BN97-00102A ASSY SMD GD17NS SNA
BD101 2007-000070 R-CHIP 0ohm,5%,1/16W,DA,TP,1608
BD102 2007-000070 R-CHIP 0ohm,5%,1/16W,DA,TP,1608
BD103 2007-000070 R-CHIP 0ohm,5%,1/16W,DA,TP,1608
BD104 3301-001163 CORE-FERRITE BEAD AB,80ohm,2x1.25x1mm,300mA,TP,FERRITE,0.08ohm
BD201 3301-001163 CORE-FERRITE BEAD AB,80ohm,2x1.25x1mm,300mA,TP,FERRITE,0.08ohm
BD202 3301-001163 CORE-FERRITE BEAD AB,80ohm,2x1.25x1mm,300mA,TP,FERRITE,0.08ohm
BD203 3301-001163 CORE-FERRITE BEAD AB,80ohm,2x1.25x1mm,300mA,TP,FERRITE,0.08ohm
BD204 3301-001163 CORE-FERRITE BEAD AB,80ohm,2x1.25x1mm,300mA,TP,FERRITE,0.08ohm
BD205 3301-001163 CORE-FERRITE BEAD AB,80ohm,2x1.25x1mm,300mA,TP,FERRITE,0.08ohm
BD206 3301-001163 CORE-FERRITE BEAD AB,80ohm,2x1.25x1mm,300mA,TP,FERRITE,0.08ohm
BD207 3301-001163 CORE-FERRITE BEAD AB,80ohm,2x1.25x1mm,300mA,TP,FERRITE,0.08ohm
BD401 3301-001163 CORE-FERRITE BEAD AB,80ohm,2x1.25x1mm,300mA,TP,FERRITE,0.08ohm
BD402 3301-001163 CORE-FERRITE BEAD AB,80ohm,2x1.25x1mm,300mA,TP,FERRITE,0.08ohm
BD403 3301-001163 CORE-FERRITE BEAD AB,80ohm,2x1.25x1mm,300mA,TP,FERRITE,0.08ohm
BD404 3301-001163 CORE-FERRITE BEAD AB,80ohm,2x1.25x1mm,300mA,TP,FERRITE,0.08ohm
BD501 3301-001163 CORE-FERRITE BEAD AB,80ohm,2x1.25x1mm,300mA,TP,FERRITE,0.08ohm
C101 2402-001044 C-AL,SMD 100uF,20%,25V,-,TP,8.3x8.3x6.3
C102 2203-000257 C-CERAMIC,CHIP 10nF,10%,50V,X7R,TP,1608
C105 2402-000108 C-AL,SMD 10uF,20%,16V,WT,TP,4.3x4.3x5.4
GD17N*/GD17A* 7-1
Loc. No. Code No. Description Specification Remarks
7 Electrical Parts List
7-1-1 GD17N* Main PCB Parts

C106 2402-000176 C-AL,SMD 10uF,20%,16V,GP,TP,4.3x4.3x5.4
C107 2402-000176 C-AL,SMD 10uF,20%,16V,GP,TP,4.3x4.3x5.4
C108 2402-000176 C-AL,SMD 10uF,20%,16V,GP,TP,4.3x4.3x5.4
C109 2402-001081 C-AL,SMD 100uF,20%,25V,WT,TP,8.3x8.3x10
C110 2402-001081 C-AL,SMD 100uF,20%,25V,WT,TP,8.3x8.3x10
C111 2402-001086 C-AL,SMD 100UF,20%,16V,WT,TP,6.6X6.6X5.3
C113 2402-001044 C-AL,SMD 100uF,20%,25V,-,TP,8.3x8.3x6.3
C114 2402-001042 C-AL,SMD 100uF,20%,16V,GP,TP,6.6x6.6x5.4mm
C115 2402-001044 C-AL,SMD 100uF,20%,25V,-,TP,8.3x8.3x6.3
C116 2402-000144 C-AL,SMD 3.3uF,20%,50V,GP,TP,4.3x4.3x5.
C117 2203-000257 C-CERAMIC,CHIP 10nF,10%,50V,X7R,TP,1608
C118 2203-000257 C-CERAMIC,CHIP 10nF,10%,50V,X7R,TP,1608
C119 2203-000257 C-CERAMIC,CHIP 10nF,10%,50V,X7R,TP,1608
C120 2203-000257 C-CERAMIC,CHIP 10nF,10%,50V,X7R,TP,1608
C121 2203-000257 C-CERAMIC,CHIP 10nF,10%,50V,X7R,TP,1608
C122 2203-000257 C-CERAMIC,CHIP 10nF,10%,50V,X7R,TP,1608
C123 2203-000236 C-CERAMIC,CHIP 0.1nF,5%,50V,NP0,TP,1608
C124 2203-000236 C-CERAMIC,CHIP 0.1nF,5%,50V,NP0,TP,1608
C125 2203-000189 C-CERAMIC,CHIP 100nF,+80-20%,25V,Y5V,TP,1608,
C126 2203-000189 C-CERAMIC,CHIP 100nF,+80-20%,25V,Y5V,TP,1608,
C127 2203-000189 C-CERAMIC,CHIP 100nF,+80-20%,25V,Y5V,TP,1608,
C128 2203-000189 C-CERAMIC,CHIP 100nF,+80-20%,25V,Y5V,TP,1608,
C129 2203-000189 C-CERAMIC,CHIP 100nF,+80-20%,25V,Y5V,TP,1608,
C130 2203-000189 C-CERAMIC,CHIP 100nF,+80-20%,25V,Y5V,TP,1608,
C131 2203-000189 C-CERAMIC,CHIP 100nF,+80-20%,25V,Y5V,TP,1608,
C132 2203-000189 C-CERAMIC,CHIP 100nF,+80-20%,25V,Y5V,TP,1608,
C133 2203-000189 C-CERAMIC,CHIP 100nF,+80-20%,25V,Y5V,TP,1608,
C134 2203-005065 C-CERAMIC,CHIP 1000nF,+80-20%,10V,Y5V,TP,1608
C135 2203-005065 C-CERAMIC,CHIP 1000nF,+80-20%,10V,Y5V,TP,1608
C136 2203-005065 C-CERAMIC,CHIP 1000nF,+80-20%,10V,Y5V,TP,1608
C137 2203-005065 C-CERAMIC,CHIP 1000nF,+80-20%,10V,Y5V,TP,1608
C138 2203-005065 C-CERAMIC,CHIP 1000nF,+80-20%,10V,Y5V,TP,1608
C139 2203-005065 C-CERAMIC,CHIP 1000nF,+80-20%,10V,Y5V,TP,1608
C140 2203-005065 C-CERAMIC,CHIP 1000nF,+80-20%,10V,Y5V,TP,1608
C142 2203-005065 C-CERAMIC,CHIP 1000nF,+80-20%,10V,Y5V,TP,1608
C144 2203-000697 C-CERAMIC,CHIP 0.002nF,0.25pF,50V,NP0,TP,1608
C145 2203-000697 C-CERAMIC,CHIP 0.002nF,0.25pF,50V,NP0,TP,1608
C146 2203-000697 C-CERAMIC,CHIP 0.002nF,0.25pF,50V,NP0,TP,1608
C151 2402-001044 C-AL,SMD 100uF,20%,25V,-,TP,8.3x8.3x6.3
C152 2203-000189 C-CERAMIC,CHIP 100nF,+80-20%,25V,Y5V,TP,1608,
C153 2203-000257 C-CERAMIC,CHIP 10nF,10%,50V,X7R,TP,1608
C154 2402-001042 C-AL,SMD 100uF,20%,16V,GP,TP,6.6x6.6x5.4mm
C170 2402-000176 C-AL,SMD 10uF,20%,16V,GP,TP,4.3x4.3x5.4
C201 2402-000179 C-AL,SMD 47uF,20%,16V,GP,TP,6.6x6.6x5.4
C202 2402-000176 C-AL,SMD 10uF,20%,16V,GP,TP,4.3x4.3x5.4
C203 2402-000176 C-AL,SMD 10uF,20%,16V,GP,TP,4.3x4.3x5.4
C204 2402-000176 C-AL,SMD 10uF,20%,16V,GP,TP,4.3x4.3x5.4
C205 2203-000189 C-CERAMIC,CHIP 100nF,+80-20%,25V,Y5V,TP,1608,
C206 2203-000189 C-CERAMIC,CHIP 100nF,+80-20%,25V,Y5V,TP,1608,
C207 2203-000189 C-CERAMIC,CHIP 100nF,+80-20%,25V,Y5V,TP,1608,
C208 2203-001077 C-CERAMIC,CHIP 0.056nF,5%,50V,NP0,TP,2012
C209 2203-001077 C-CERAMIC,CHIP 0.056nF,5%,50V,NP0,TP,2012
C210 2203-000257 C-CERAMIC,CHIP 10nF,10%,50V,X7R,TP,1608
C211 2203-000257 C-CERAMIC,CHIP 10nF,10%,50V,X7R,TP,1608
C212 2203-000257 C-CERAMIC,CHIP 10nF,10%,50V,X7R,TP,1608
C213 2203-000257 C-CERAMIC,CHIP 10nF,10%,50V,X7R,TP,1608
C214 2203-000257 C-CERAMIC,CHIP 10nF,10%,50V,X7R,TP,1608
C215 2203-000257 C-CERAMIC,CHIP 10nF,10%,50V,X7R,TP,1608
C216 2203-000257 C-CERAMIC,CHIP 10nF,10%,50V,X7R,TP,1608
C217 2203-000257 C-CERAMIC,CHIP 10nF,10%,50V,X7R,TP,1608
C218 2203-000257 C-CERAMIC,CHIP 10nF,10%,50V,X7R,TP,1608
7 Electrical Parts List
7-2 GD17N*/GD17A*
Loc. No. Code No. Description Specification Remarks
CONFIDENTIAL

C219 2203-000257 C-CERAMIC,CHIP 10nF,10%,50V,X7R,TP,1608
C220 2203-005065 C-CERAMIC,CHIP 1000nF,+80-20%,10V,Y5V,TP,1608
C221 2203-005065 C-CERAMIC,CHIP 1000nF,+80-20%,10V,Y5V,TP,1608
C222 2203-005065 C-CERAMIC,CHIP 1000nF,+80-20%,10V,Y5V,TP,1608
C223 2203-005065 C-CERAMIC,CHIP 1000nF,+80-20%,10V,Y5V,TP,1608
C224 2203-005065 C-CERAMIC,CHIP 1000nF,+80-20%,10V,Y5V,TP,1608
C225 2203-005065 C-CERAMIC,CHIP 1000nF,+80-20%,10V,Y5V,TP,1608
C226 2203-000384 C-CERAMIC,CHIP 0.015nF,5%,50V,NP0,TP,1608
C227 2203-000384 C-CERAMIC,CHIP 0.015nF,5%,50V,NP0,TP,1608
C301 2203-000189 C-CERAMIC,CHIP 100nF,+80-20%,25V,Y5V,TP,1608,
C302 2402-000176 C-AL,SMD 10uF,20%,16V,GP,TP,4.3x4.3x5.4
C303 2402-000176 C-AL,SMD 10uF,20%,16V,GP,TP,4.3x4.3x5.4
C304 2402-000176 C-AL,SMD 10uF,20%,16V,GP,TP,4.3x4.3x5.4
C305 2402-000176 C-AL,SMD 10uF,20%,16V,GP,TP,4.3x4.3x5.4
C306 2402-000108 C-AL,SMD 10uF,20%,16V,WT,TP,4.3x4.3x5.4
C307 2402-000176 C-AL,SMD 10uF,20%,16V,GP,TP,4.3x4.3x5.4
C308 2402-000176 C-AL,SMD 10uF,20%,16V,GP,TP,4.3x4.3x5.4
C309 2402-000176 C-AL,SMD 10uF,20%,16V,GP,TP,4.3x4.3x5.4
C310 2402-000179 C-AL,SMD 47uF,20%,16V,GP,TP,6.6x6.6x5.4
C311 2402-000179 C-AL,SMD 47uF,20%,16V,GP,TP,6.6x6.6x5.4
C314 2402-001006 C-AL,SMD 4.7uF,20%,25V,GP,TP,3.6x6.3x3.
C315 2402-001006 C-AL,SMD 4.7uF,20%,25V,GP,TP,3.6x6.3x3.
C316 2203-000189 C-CERAMIC,CHIP 100nF,+80-20%,25V,Y5V,TP,1608,
C317 2203-000189 C-CERAMIC,CHIP 100nF,+80-20%,25V,Y5V,TP,1608,
C318 2203-000189 C-CERAMIC,CHIP 100nF,+80-20%,25V,Y5V,TP,1608,
C319 2203-000189 C-CERAMIC,CHIP 100nF,+80-20%,25V,Y5V,TP,1608,
C320 2203-000189 C-CERAMIC,CHIP 100nF,+80-20%,25V,Y5V,TP,1608,
C321 2203-000189 C-CERAMIC,CHIP 100nF,+80-20%,25V,Y5V,TP,1608,
C322 2203-000189 C-CERAMIC,CHIP 100nF,+80-20%,25V,Y5V,TP,1608,
C323 2203-000189 C-CERAMIC,CHIP 100nF,+80-20%,25V,Y5V,TP,1608,
C324 2203-000189 C-CERAMIC,CHIP 100nF,+80-20%,25V,Y5V,TP,1608,
C325 2203-000189 C-CERAMIC,CHIP 100nF,+80-20%,25V,Y5V,TP,1608,
C326 2203-000189 C-CERAMIC,CHIP 100nF,+80-20%,25V,Y5V,TP,1608,
C327 2203-000189 C-CERAMIC,CHIP 100nF,+80-20%,25V,Y5V,TP,1608,
C340 2203-000189 C-CERAMIC,CHIP 100nF,+80-20%,25V,Y5V,TP,1608,
C341 2203-000189 C-CERAMIC,CHIP 100nF,+80-20%,25V,Y5V,TP,1608,
C342 2203-000189 C-CERAMIC,CHIP 100nF,+80-20%,25V,Y5V,TP,1608,
C343 2203-000189 C-CERAMIC,CHIP 100nF,+80-20%,25V,Y5V,TP,1608,
C344 2203-000189 C-CERAMIC,CHIP 100nF,+80-20%,25V,Y5V,TP,1608,
C345 2203-000189 C-CERAMIC,CHIP 100nF,+80-20%,25V,Y5V,TP,1608,
C346 2203-000189 C-CERAMIC,CHIP 100nF,+80-20%,25V,Y5V,TP,1608,
C347 2203-000189 C-CERAMIC,CHIP 100nF,+80-20%,25V,Y5V,TP,1608,
C348 2203-000189 C-CERAMIC,CHIP 100nF,+80-20%,25V,Y5V,TP,1608,
C349 2203-000189 C-CERAMIC,CHIP 100nF,+80-20%,25V,Y5V,TP,1608,
C350 2203-000189 C-CERAMIC,CHIP 100nF,+80-20%,25V,Y5V,TP,1608,
C351 2203-000189 C-CERAMIC,CHIP 100nF,+80-20%,25V,Y5V,TP,1608,
C352 2203-000189 C-CERAMIC,CHIP 100nF,+80-20%,25V,Y5V,TP,1608,
C353 2203-000189 C-CERAMIC,CHIP 100nF,+80-20%,25V,Y5V,TP,1608,
C354 2203-000189 C-CERAMIC,CHIP 100nF,+80-20%,25V,Y5V,TP,1608,
C355 2203-000189 C-CERAMIC,CHIP 100nF,+80-20%,25V,Y5V,TP,1608,
C356 2203-000189 C-CERAMIC,CHIP 100nF,+80-20%,25V,Y5V,TP,1608,
C357 2203-000189 C-CERAMIC,CHIP 100nF,+80-20%,25V,Y5V,TP,1608,
C358 2203-000189 C-CERAMIC,CHIP 100nF,+80-20%,25V,Y5V,TP,1608,
C359 2203-000189 C-CERAMIC,CHIP 100nF,+80-20%,25V,Y5V,TP,1608,
C360 2203-000189 C-CERAMIC,CHIP 100nF,+80-20%,25V,Y5V,TP,1608,
C361 2203-000189 C-CERAMIC,CHIP 100nF,+80-20%,25V,Y5V,TP,1608,
C363 2203-000384 C-CERAMIC,CHIP 0.015nF,5%,50V,NP0,TP,1608
C365 2203-000257 C-CERAMIC,CHIP 10nF,10%,50V,X7R,TP,1608
C366 2203-000257 C-CERAMIC,CHIP 10nF,10%,50V,X7R,TP,1608
C367 2203-000257 C-CERAMIC,CHIP 10nF,10%,50V,X7R,TP,1608
C368 2203-000257 C-CERAMIC,CHIP 10nF,10%,50V,X7R,TP,1608
7 Electrical Parts List
GD17N*/GD17A* 7-3
Loc. No. Code No. Description Specification Remarks
CONFIDENTIAL