Samsung SyncMaster 2043BW User manual

ii
LCD MONITOR
quick start guide

Introduction
Package Contents
Note
Please make sure the following items are included with your monitor.
If any items are missing, contact your dealer.
Contact a local dealer to buy optional items.
Unpacking
Type 1
Monitor & Simple stand
Note
• MagicRotation program can not be provided as Simple Stand does not support Pivot function.
Type 2
Monitor & HAS stand
Type 3
8

Monitor & Dual Hinge Stand
Type 4
Monitor & HAS stand
23 inches or larger
Manuals
Quick Setup Guide Warranty Card
(Not available in all loca-
tions)
User's Guide
Cables
D-Sub Cable Power Cord DVI Cable (option)
USB Cable
(Applicable to the stand mod-
elsthathaveUSB portsonly.)
Audio Cable
(Supplied for the models that
have speakers only.)
Others
Cleaning Cloth(Option) Cable holding ring
Introduction
9

Note
Cleaning Cloth is only provided for highly polished black products as a product feature.
Your Monitor
Initial Settings
Select the language using the up or down key.
The displayed content will disappear after 40 seconds.
Turn the Power button off and on. It will be displayed again.
It can be displayed up to three (1) times. Make sure to adjust the resolution of your PC before reaching
the maximum count.
Note
The resolution displayed on the screen is the optimal resolution for this product.
Adjust your PC resolution so that it is the same as the optimal resolution for this product.
Introduction
10

Front
Note
Touch them lightly with your fingers to use them.
MENU button [MENU/ ]
Openstheon-screen menu andexitsfromthe menu. Alsouseto exit theOSDmenu
or return to the previous menu.
Customized Key[ ]
You can customize key assignment for the Custom button according to your pref-
erences.
Note
You can configure the customized key for a required function via Setup > Cus-
tomized Key.
Adjust buttons [ ]
These buttons allow you to adjust items in the menu.
Brightness button [ ]
When OSD is not on the screen, push the button to adjust brightness.
Introduction
11

button
Push the ' ', then selects the video signal while the OSD is off. (When the ' '
button is pressed to change the input mode, a message appears in the upper left of
the screen displaying the current mode -- analog or digital input signal.)
Note
•If you select the digital mode, you must connect your monitor to the graphic
card's DVI port using the DVI cable.
• This function is not available for products with an Analog interface only.
Enter button [ ]
Activates a highlighted menu item.
AUTO button
Use this button for auto adjustment.
(Available in Analog mode only)
Power button [ ]
Use this button for turning the product on and off.
Power Indicator
This light is lit when operating normally, and blinks once when your adjustments
are saved.
Note
See PowerSaver described in the manual for further information regarding power
saving functions. For energy conservation, turn your monitor OFF when it is not
needed or when leaving it unattended for long periods.
Volume button[ ]
When OSD is not on the screen, push the button to adjust volume.
Note
Applicable to the models that have speakers only.
Headphone sound output terminal[ ]
Note
Applicable to the models that have speakers only.
Speaker
You can hear sound by connecting the soundcard of your PC to the monitor.
Introduction
12

Note
Applicable to the models that have speakers only.
Rear
Note
The configuration at the back of the monitor may vary from product to product.
POWER port
POWER port
Connect the power cord for your monitor to the
POWER port on the back of the product.
DVI IN
DVI IN
Connect the DVI Cable to the DVI IN port on the
back of your monitor.
Note
Applicable to the digital (DVI)-dedicated models
only.
RGB IN
RGB IN
Connect the D-sub cable to the 15-pin, RGB IN
port on the back of your monitor.
USB connection termi-
nal (Option)
Introduction
13

UP(USB upstream port)
Connect the UP port of the monitor and the
USB port of the computer with the USB cable.
DOWN(USB downstream port)
Connectthe DOWNportoftheUSBmonitor
and a USB device with the USB cable.
Note
Applicable to the models that have USB ports
only.
AUDIO IN port
AUDIO IN port
Connect the audio cable for your monitor to the
audio port on the back of your computer.
Note
Applicable to the models that have speakers only.
Kensington Lock
Kensington Lock
The Kensington lock is a device used to physi-
cally fix the system when using it in a public
place. (The locking device has to be purchased
separately.) For using a locking device, contact
where you purchase it.
Note
The location of the Kensington Lock may be dif-
ferent depending on its model.
Using the Anti-Theft Kensington Lock
1. InsertthelockingdeviceintotheKensington
slot on the Monitor and turn it in the
locking direction .
2. Connect the Kensington Lock cable.
3. FixtheKensingtonLockto a deskoraheavy
stationary object.
Note
See Connecting Cables for further information regarding cable connections.
Introduction
14

Cable holding ring
• Fix the cables using the holding ring, as shown in the figure.
Introduction
15

Connections
Connecting Cables
Use a connection appropriate for your computer.
Using the D-sub (Analog) connector on the video card.
• Connect the signal cable to the 15-pin, D-sub port on the back of your monitor.
Using the DVI (Digital) connector on the video card.
• Connect the DVI Cable to the DVI IN Port on the back of your Monitor.
16