Samsung WMN4070SD User manual

Angle Adjustment and Rotation Type
Wall-Mount Bracket Installation Guide
WMN4070SD
Product Image
Components
Only use the supplied components for the bracket installation.
Safety Instructions
Be sure to contact an authorized service center when installing your set.
1. Be sure to keep the product away from children. There can be serious damage on the head when hit by the edge of the product.
2. Be careful when you adjust the angle or rotate the set. The product can be damaged if it is too close to touch the wall.
(Attach some sponges to 4 corners of the product to avoid the product or wall damage.)
3. Do not install the product in a place with high temperature and high humidity. Avoid to install the product on the wall which can-
not bear the weight.
4. Since there is a danger of electric shock, do not insert your fi ngers into the TV stand installation hole while installing the TV.
5. Make sure to cover the TV stand installation hole with the hole cover supplied with the TV before completing the wall installation.
Contact a qualified technician at your dealer for
moving or replacing the product after the installation.
Do not hang on or give sudden impacts to the product.
Angle Adjustment Bracket
1
Accessories
LFD
Screwⓑ: 4
RH, M8,
L23, WHT
Screwⓐ: 7 Anchor : 7
Wire Fixing Tool : 1Assembling Tool
WMN4070SD-eng-wall mount.indd 1 2011-06-22 �� 6:04:17

Wall Bracket Assembly
1Install the angle adjustment bracket on the wall as
shown in the figure.
Tighten the angle adjustment bracket by using anchors
and screwsⓐorderly from ①to ⑦. (Turn the rotating part
of the bracket to the right or left to install the bracket more
easily.)
If it cannot be installed on the assigned area, install at the
nearest place.
Check the solidity of the wall before the installation. Strengthen the wall and install the bracket if the wall is
not firm enough.
The supplied screws and anchors are for installing on concrete walls.
For the wall of plaster, marble, or steel, use the appropriate screws.
2Remove the screws on the product. Tighten the 4 screwsⓑon the back panel by using the assembling tool.
Be sure that 5 mm of each screw is left to be unscrewed.
(About 5 mm space is required to hang on the angle adjustment bracket.)
※When installing the LFD, assemble the LFD using the holder-ring injection mold supplied with the LFD.
Supplied
Holder-Ring
Mount the product on the wall bracket. Be sure to check on the left and right side to see if it is properly fixed.
Be careful when installing the product or adjusting the angle as fingers can be caught in the holes.
Be sure the wall bracket is securely fixed to the wall. Falling down the product may cause physical damage.
LFD
How to Tighten Anchors or Screwsⓐ
※Use the drill with the required size when making a
hole in the wall.
Be sure to follow the directions for the installation
to avoid safety problems.
Make a hole in the wall with the drill
of 6X50. (WMN-2370 : 5X40)
Clean up the hole.
Insert the supplied anchor to the hole.
Match the angle adjustment bracket
to the holes on the wall and tighten
the screwsⓐ.
23 65
4 7
1
WMN4070SD-eng-wall mount.indd 2 2011-06-22 �� 6:04:18

3Pull the wall bracket fixing part forward. Two people are required to install the product on the assigned area of the
wall bracket.
4For managing the power cord and other cables for peripheral equipments, bundle the wires by using the supplied
wire fixing tool. Be sure the wires are not unbundled or came off when rotating or operating.
※Insert the cables and pull the angle adjustment bracket forward. Arrange the wires by using the hole to avoid the
interference with wires when rotating the set.
Check the operation 2 ~ 3 times and fix the wall molding if it works properly.
WMN4070S
Fix the TV set to the wall bracket and tighten again with 4 screwsⓑby using the
assembling tool.
(Torque : 10 ~15 Kg)
WMN4070SD-eng-wall mount.indd 3 2011-06-22 �� 6:04:18

Wall Bracket Angle Adjustment
※The smooth moving mechanism is applied to this product to move the product smoothly for
convenience.
Do not adjust the angle with force. The product can be
damaged if it is too close to touch the wall.
Hold the left and right side of the product when you want
to adjust the left and right angle.
Hold the top center to adjust the up and down angle.
Product Specifications
[ Set Fixing Part ] [ Screw Fixing Part ]
Product Standards
Information in this document is subject to change without notice.
WMN4070SD
Width (mm) 248
Height (mm) 255
Dept (mm) 30
Weight (Kg) 2.4
Bracket VESA Standard 200 X 200
248
200
150
210
248
197.4 30
200
134
160 255
-10°~10°
-10°~10°
-20°~20°
-20°~20°
※You can adjust the angle vertically within a range of
-10° ~ 10° and horizontally within a range of -20° ~ 20°.
The adjustable angle range may be vary depending on
the model.
WMN4070SD-eng-wall mount.indd 4 2011-06-22 �� 6:04:18