Samsung SADT-100EC User manual

SADT - 100EC
imagine the possibilities
Thank you for purchasing this Samsung product.
To receive more complete service, please
register your product at
www.samsung.com/global/register
Ceiling Mount Adaptor
SADT-100EC_ENG.indd 1 2008-01-23 오후 4:14:36

ENG
SADT-100EC_1
Overview
The ceiling mount adaptor (SADT-100EC) is used for the smart dome
camera to be installed in a double ceiling of the concealed type.
Notice
• Select an installation spot which can endure more than 4 times of the product weight.
• Install the device in the spot where more than 200mm in space is provided above the
ceiling board.
• It can be installed only when the ceiling board is less than 40mm thick.
• Make sure to use a safety wire that can prevent falling.
• When you install the camera on the adaptor, be sure to use the fixing screw which is
provided with the adaptor.
Installation
1. Use template A to drill a hole in the ceiling.
Remove the circular shape (“C”) from the center of template A.
Place template A on the ceiling board where to install the ceiling mount adaptor and
drill a Ø219mm hole on it.
The shape of the hole is as follows.
Over 200mm
CEILING BOARD Within 40mm
TEMPLATE A
CEILING B/D
Ø219 mm
Ø219
“C”
SADT-100EC_ENG.indd 1 2008-01-23 오후 4:14:37

2_SADT-100EC
2. Install two anchor bolts (B1,B2) on the concrete ceiling.
Insert the anchor bolt (B1) into the Ø219 hole.
- Determine the length of the anchor bolt (B1) using the template B (accessory).
- Apply a nut (N1) to the anchor bolt(B1) using template B (accessory) and determine
the location.
Tighten another anchor bolt (B2) as shown on the following drawing.
3. Install the safety wire to the anchor bolt (B2) in the following sequence.
Apply a nut (N2) to the anchor bolt (B2).
Insert the safety bracket 1(supported) into the anchor bolt(B2).
Apply two nuts (N3,N4) to the anchor bolt (B2).
Hook and insert a safety wire into the safety bracket1.
Put up and fit the opposite end of the safety wire onto the safety bracket 2 for the
ceiling mount adaptor.
CONCRETE
ANCHOR BOLT
CEILING B/D
TEMPLATE B
“B2” “B1”
“N1”
SAFETY
BRACKET 1
SAFETY BRACKET 1
SAFETY WIRE
CEILING B/D
SAFETY BRACKET 2
CEILING MOUNT ADAPTOR
“N2”
“N3”
“N4”
“B2” “B1”
“N1”
SADT-100EC_ENG.indd 2 2008-01-23 오후 4:14:37

ENG
SADT-100EC_3
4. Insert necessary wiring including the external power cable, video out cable and alarm I/O
cable into the side hole of the adaptor.
See the installation guide for the applicable camera, and arrange necessary cables for the
installation in advance.
5. Screw the anchor bolt (B1) into the ceiling mount adaptor.
Insert the adaptor through the hole inside the ceiling.
Then push the anchor bolt fixing hole into the ceiling so that it fits the anchor bolt (B1).
Turn the three screws on the ceiling mount adaptor clockwise to secure the adaptor to
the ceiling board. (The bracket is moved from A to B.)
Turn to the clockwise
“B1”
“B2”
“N1”
HOLE for fixing a anchor bolt
CEILING B/D
CEILING MOUNT ADAPTOR
BRACKET
CEILING B/D SCREW for fixing a ADAPTOR
SADT-100EC_ENG.indd 3 2008-01-23 오후 4:14:38

4_SADT-100EC
6. Insert and firmly secure the anchor bolt (B1) into the two nuts (N5, N6).
CEILING B/D
BRAKET
BRAKET
< A > < B >
CEILING B/D
“B2” “B1”
“N1”
“N5”
“N6”
SADT-100EC_ENG.indd 4 2008-01-23 오후 4:14:39

ENG
SADT-100EC_5
7. Prepare the camera adapter of the CAMERA to install.
Connect the power cable, video out cable and alarm I/O cable to the camera adaptor.
When connect the video output cable, use the L type BNC adapter(suported).
For more information, see the installation guide for the SmartDome camera.
8. Arrange the cables, and then fix the camera adapter into the screw fixing hole of bracket
adapter attached to ceiling mount adapter by using 4 screws (M3×L6, included in camera
product).
Fasten the camera adaptor so that the lever of the camera faces the opposite side of the
internal projections of the adaptor.
POWER CABLE
VIDEO OUT
ALARM IN/OUT
CAMERA ADAPTOR
BNC ADAPTOR
L TYPE
CEILING MOUNT ADAPTOR
BRACKET ADAPTOR
CAMERA ADAPTOR
BRACKET ADAPTOR
Extrusion RIB
LEVER
BNC ADAPTOR-
L TYPE
CAMERA ADAPTOR
LEVER
BRACKET ADAPTOR
The hole for
joining a SCREW
Extrusion RIB
SADT-100EC_ENG.indd 5 2008-01-23 오후 4:14:42

6_SADT-100EC
9. Use the screws on the Wiring Support Tube plate to fix it.
10. Put up the safety wire, attached to the camera, on the safety hook.
CAUTION
Durin g installation or detachment, to avoid safety accident and camera damage
due to the fall, make sure the safety wire is secured to the hook.
PLATE for fixing Wiring Support Tube
CEILING
SAFETY HANGER SAFETY HANGER
SAFETY WIRE SAFETY WIRE
CAMERA CAMERA
SADT-100EC_ENG.indd 6 2008-01-23 오후 4:14:45

ENG
SADT-100EC_7
11. To avoid accidental fall and consequent physical injury or damage to the camera during
installation or detachment, make sure the safety wire is secured to the hook., then insert
the 3 guides of camera to the guide hole of camera adapter. After that turn the camera
about 15 degrees clockwise.
At this time, check the coupling sound and the coupling hole of LEVER LOCK is moved
alright.
LOCK
UNLOCK
CAMERA ADAPTOR
CAMERA ADAPTOR
GUIDE HOLE
GUIDE
CAMERA
HOLE for fixing a screw
LEVER ROCK
Turn to the clockwise
about 15 degrees
< “A” >
< “B” >
CAMERA
CAMERA
CAMERA ADAPTOR
GUIDE HOLE
GUIDE
SADT-100EC_ENG.indd 7 2008-01-23 오후 4:14:47

8_SADT-100EC
12. Insert the provided screw (M3×L6, included in camera product) into the fixing hole of the
lever lock and fix it.
Once you removed the camera from the camera adaptor, loosen the screw (BH M3xL6).
With the lever lock turned clockwise, turn the camera counter clockwise and then pull it
down.
13. Insert the cover body into the dome of the camera.
Make sure that the 9 snap pits fit into the corresponding holes of the ceiling mount.
CEILING MOUNT ADAPTOR
CONNECTING HOLE
SNAP-FIT
COVER BODY
SADT-100EC_ENG.indd 8 2008-01-23 오후 4:14:48

ENG
SADT-100EC_9
Product Specification
Size: Ø235 X H210
Weight: 765g
Operation Temperature: -10˚C ~ 50˚C
Accessories
Safety wire .......................................... 1
Safety bracket
..................................... 1
Template A .......................................... 1
Template B
.......................................... 1
MANUAL ............................................. 1
BNC ADAPTOR-L TYPE
......................
1



Ø235
SADT-100EC_ENG.indd 9 2008-01-23 오후 4:14:49