Samsung SCC-B539X User manual

User’s Guide
SCC-B539X
Vari-focal Anti-Vandal Dome Camera
ENG RUS POL
AB68-00649E(01)Eng.indd 1 2007-05-14 ｿﾀﾈﾄ 7:55:42

2
3
This symbol indicates high voltage
is present inside. It is dangerous to
make any kind of contact with any
inside part of this product.
This symbol alerts you that important
literature concerning operation and
maintenance has been included with
this product.
To prevent damage which may result in fire
or electric shock hazard, do not expose this
appliance to rain or moisture.
WARNING
1. Be sure to use only the standard adapter
that is specified in the specification
sheet. Using any other adapter could
cause fire, electrical shock, or damage
to the product
2. Incorrectly connecting the power
supply or replacing battery may cause
explosion, fire, electric shock, or damage
to the product.
3. Do not connect multiple cameras to a
single adapter. Exceeding the capacity
may cause abnormal heat generation or
fire.
4. Securely plug the power cord into the
power receptacle. Insecure connection
may cause fire.
5. When installing the camera, fasten it
securely and firmly. A falling camera may
cause personal injury.
6. Do not place conductive objects (e.g.
screwdrivers, coins, metal things, etc.) or
containers filled with water on top of the
camera. Doing so may cause personal
injury due to fire, electric shock, or falling
objects.
7. Do not install the unit in humid, dusty, or
sooty locations. Doing so may cause fire
or electric shock.
8. If any unusual smells or smoke come
from the unit, stop using the product. In
such case, immediately disconnect the
power source and contact the service
center. Continued use in such a condition
may cause fire or electric shock.
Safety Precautions
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE REAR
COVER. NO USER SERVICEABLE PARTS
INSIDE. REFER TO QUALIFIED SERVICE
PERSONNEL.
CAUTION
RISK OF ELECTRIC
SHOCK DO NOT OPEN
AB68-00649E(01)Eng.indd 2 2007-05-14 ｿﾀﾈﾄ 7:55:42

2
ENG
3
9. If this product fails to operate normally,
contact the nearest service center. Never
disassemble or modify this product
in any way. (SAMSUNG is not liable
for problems caused by unauthorized
modifications or attempted repair.)
10. When cleaning, do not spray water
directly onto parts of the product. Doing
so may cause fire or electric shock.
CAUTION
1. Do not drop objects on the product or
apply strong shock to it. Keep away from
a location subject to excessive vibration
or magnetic interference.
2. Do not install in a location subject to
high temperature (over 122°F), low
temperature (below 14°F), or high
humidity. Doing so may cause fire or
electric shock.
3. If you want to relocate the already
installed product, be sure to turn off the
power and then move or reinstall it.
4. Remove the power plug from the
outlet when then there is a lightning.
Neglecting to do so may cause fire or
damage to the product.5.
Keep out of direct sunlight and heat
radiation sources. It may cause fire.
6. Install it in a place with good ventilation.
7. Avoid aiming the camera directly towards
extremely bright objects such as sun,
as this may damage the CCD image
sensor.
8. Apparatus shall not be exposed to
dripping or splashing and no objects
filled with liquids, such as vases, shall be
placed on the apparatus.
9. The Mains plug is used as a disconnect
device and shall stay readily operable at
any time.
FCC Statement
This device complies with part 15 of the FCC
Rules. Operation is subject to the following
two conditions:
1) This device may not cause harmful
interference, and
2) This device must accept any interference
received including interference that may
cause undesired operation.
Note
This equipment has been tested and found to
comply with the limits for a Class A digital device,
pursuant to part 15 of FCC Rules. These limits
are designed to provide reasonable protection
against harmful interference when the equipment
is operated in a commercial environment. This
equipment generates, uses, and can radiate
radio frequency energy and, if not installed
and used in accordance with the instruction
manual, may cause harmful interference to radio
communications. Operation of this equipment
in a residential area is likely to cause harmful
interference in which case the user will be
required to correct the interference at his own
expense.
AB68-00649E(01)Eng.indd 3 2007-05-14 ｿﾀﾈﾄ 7:55:42

4
5
Important Safety Instructions
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings.
Install in accordance with the
manufacturer’s instructions.
8. Do not install near any heat sources
such as radiators, heat registers, or
other apparatus (including amplifiers)
that produce heat.
9. Do not defeat the safety purpose of
the polarized or grounding-type plug.
A polarized plug has two blades with
one wider than the other. A grounding
type plug has two blades and a third
grounding prong. The wide blade or the
third prong is provided for your safety.
If the provided plug does not fit into
your outlet, consult an electrician for
replacement of the obsolete outlet.
10. Protect the power cord from being
walked on or pinched particularly at
plugs, convenience receptacles, and the
point where they exit from the apparatus.
11. Only use attachments/accessories
specified by the manufacturer.
12. Use only with cart, stand, tripod, bracket,
or table specified by the manufacturer, or
sold with the apparatus.
13. Unplug this apparatus. When a cart is
used, use caution when moving the
cart/apparatus combination to avoid
injury from tip-over.
14. Refer all servicing to qualified service
personnel. Servicing is required when
the apparatus has been damaged in any
way, such as power-supply cord or plug
is damaged, liquid has been spilled or
objects have fallen into the apparatus,
the apparatus has been exposed to rain
or moisture, does not operate normally,
or been dropped.
AB68-00649E(01)Eng.indd 4 2007-05-14 ｿﾀﾈﾄ 7:55:43

4
ENG
5
Overview
..............................................................................................
6
About this guide ............................................................................6
Product overview ...........................................................................6
Main features .................................................................................6
Components ...................................................................................7
Checking components in the package .......................................7
Components of your camera ......................................................8
Installation
..........................................................................................
9
Setting switches ............................................................................9
Setting function switches ............................................................9
Connecting cables and changing the settings ......................... 11
Installing camera .........................................................................12
Before installation .....................................................................12
About the installation holes ......................................................12
Installing on a pipe ...................................................................13
Installing the camera on the ceiling ..........................................15
Disassembling/assembling the Main body from the Case .......16
Adjusting the camera direction ..................................................17
Appendix A: Specifications for NTSC Standard
.................
18
Appendix B: Specifications for PAL Standard ...................... 19
Contents
AB68-00649E(01)Eng.indd 5 2007-05-14 ｿﾀﾈﾄ 7:55:43

6
7
Overview
❚ About this guide
This user guide includes basic instructions for
the product. It is recommended that all users
read this guide before use.
This guide is divided as follows:

Chapter 1, “Overview,” introduces the user guide
and product related information. (This chapter)

Chapter 2, “Installation,” explains how to set and
install the product.
 Appendix, “Specifications,” provides the
specifications of the product.
❚ Product overview
This anti-vandal dome camera provides
the superb monitoring features in bank and
business areas and it is a water-proof and
vibration-proof camera, which can strongly
endure an external impact. This vari-focal
camera provides the digital noise reduction
(DNR) and real-time CCD defect correction
features for implementing a clear image.
❚ Main features

Power: DC 12V/AC 24V

Special functions

Line lock (LL) control

Auto white balancing

Horizontal/vertical image reversing

Flickerless control

Low shutter speed control

Backlight compensation control

Automatic switching between color and black
& white modes

Equipped with vari-focal lens

Auto Iris function

Digital noise reduction (DNR)

Dynamic CCD defect compensation
AB68-00649E(01)Eng.indd 6 2007-05-14 ｿﾀﾈﾄ 7:55:43

6
ENG
7
❚ Components
Checking components in the package
Please check your camera and accessories are included in the package. Those components
are as shown below:
Camera Test Monitor Cable User’s Guide
Image Part name Standard Quantity Usage
Plastic anchor HUD 5 4 (EA)
Attach each piece to screw connection
holes for strengthening connection
ASSY screw
machine
BH M5 X L6.
(White+o-ring)
8Used for filling in the holes when
installing pipe and wall mount
ASSY screw
tapping
TH M4xL30 (Black+
o-ring)
4Used when installing your camera
on the ceiling or wall
L-Wrench TROX T-20 1 Used for assembling/
disassembling the Dome cover
Template 1 Used for guiding the installation
Gasket-pipe hole T2.5 W56 1 Used to make a wiring hole when installing the camera on the
ceiling or wall
Note
The test monitor cable is used to test the camera by connecting to a portable display. If you really want to
connect the camera to a monitoring display, use the BNC cable.
AB68-00649E(01)Eng.indd 7 2007-05-14 ｿﾀﾈﾄ 7:55:44

8
9
Components of your camera
Your camera has the following components:
1. Dome cover: Covers the inner cover, lens, and main
body to protect them.
2. Cover screw: Use it to assemble or disassemble both
dome cover and case.
3. Inner cover: Covers the main body to protect it.
4. Wing locker: Push a long thin screwdriver into its
narrow spot and press it outward when you want to
remove the inner cover.
5. Main body: Includes a lens, a switch board, a PCB
board, screws, and such.
6. Screws for assembly and disassembly: Using
these 2 screws, the Main body is closely connected to
the Case.
7. Hooker: By pulling the left/right levers in the arrow
direction, the Main body can be detached from the
Case.
8. Case: Used as a ceiling or wall fixture. It is fixed using
four screws provided in the package.
9. Zoom lever: Using this lever, the lens zoom can be
adjusted and fixed.
10. Focus lever: Using this lever, the lens focus can be
adjusted and fixed.
11. Tilt fixing screw: Using this screw, the slope of the
lens can be adjusted and fixed.
12. Switch board: Includes two kinds of control switches
such as function switches and phase-control switches.
The board has eight function switches in the middle
and two phase-control buttons on each side of the
function switch area.
13. Cable: Connect the Video connector to BNC cable
and Power connector to power adapter.
1
24
Lens
9 0
!
@
3
8
#Video connector
Power connector
5
66
7
7
AB68-00649E(01)Eng.indd 8 2007-05-14 ｿﾀﾈﾄ 7:55:46

8
ENG
9
❚ Setting switches
Setting function switches
To set the available functions on your camera, adjust eight switches as shown below:
Installation
1. Switch 1 (LL): When this switch is set to
OFF, the camera operates in the internal
synchronization mode, while when it is
set to ON, the camera operates in the
line lock mode.
In the internal synchronization mode, the
camera always uses an inside crystal
oscillator for synchronization. However
if multiple cameras are connected to a
sequential switcher, picture rolling or
flickering may occur when switching from
one camera to another. In this case, you
can set this switch to ON to solve this
problem.
The line lock mode allows the camera
to use the phase of the AC power as
the synchronization reference. In this
mode, you can use the phase control
buttons(INC/DEC).
Note
When you are using the DC 12V power, set
this switch to OFF. The line lock feature will
not normally operate even when the switch is
set to ON.
No Name Brief description
1 LL Line lock ON/OFF
2 LSS Sens-up or Low speed shutter ON/OFF
3 H-REV Horizontal reverse ON/OFF
4 V-REV Vertical reverse ON/OFF
5 BLC Backlight compensation ON/OFF
6 FL Flickerless ON/OFF
7 D/N Automatic switching between color and
black & white ON/OFF
8 AWB Automatic white balance ON/OFF
8
7
6
5
4
3
2
1
INC
DEC
AB68-00649E(01)Eng.indd 9 2007-05-14 ｿﾀﾈﾄ 7:55:51

10
11
Set the LL switch to ON while the AC
power is connected. If any picture roll
happens, you have to adjust the phase
using the phase-control buttons. Press
the INC or DEC button to increase or
decrease the phase by one degree.
2. Switch 2 (LSS): This sens-up mode
accumulates the image fields in
memory to reduce noise but increase
the brightness and contrast rate. When
this switch is set to ON, the camera
automatically switches to a maximum
of 128 times of image acquisition speed
to implement a clear picture for darker
image.
3. Switch 3 (H-REV): When this switch is
set to ON, the camera image is reversed
horizontally. If you want to monitor your
site using a mirror, you can use this
feature to see the right image.
4. Switch 4 (V-REV): When this switch is
set to ON, the camera image is reversed
vertically. If your camera reluctantly
displays the vertically reversed image,
you can use this feature to see the right
image.
5. Switch 5 (BLC): When this switch is set
to ON, you can view a clear image even
though the camera faces any excessive
light such as sunlight and fluorescent
light. When it is set to OFF, the subject
with excessive light is not clearly shown.
6. Switch 6 (FL): When this switch is set
to ON, the shutter speed is fixed to
1/100 sec (for NTSC) or 1/120 sec (for
PAL) to prevent screen from flickering
by the disaccordance between vertical
synchronous frequency (50Hz for NTSC,
60Hz for PAL) and on-and-off frequency
of a light.
7. Switch 7 (D/N): When this switch is set
to ON, the camera automatically switches
between color and B&W according to the
brightness of the vicinity.
8. Switch 8 (AWB): This switch adjusts
white balancing. When this switch is set to
ON, this camera operates in ATW mode,
and in case of OFF, this camera operates
in AWC mode.
 ATW (Auto Tracking White Balance):
The color temperature is automatically
adjusted according to the environmental
change. (Approx. 2000°K to 11,000°K)
 AWC (Auto White Balance Control): It
stores the color temperature just when
the switch is changed to OFF. Accordingly
color temperatures are adjusted by the
stored value.
Caution
-. The IRIS setting range for the camera is
approximately 80 to 120 IRE. It means
the camera does not provide the IRIS
full open/close feature but the restricted
variation range.
-. Use the camera after setting to the proper
level (80 IRE or above) because the IRIS
hunting may occur when the level is 75
IRE or below.
AB68-00649E(01)Eng.indd 10 2007-05-14 ｿﾀﾈﾄ 7:55:52

10
ENG
11
❚ Connecting cables and changing the settings
Before installing your camera, you have to adjust the lens focus, zoom, and switch settings.
To connect cables
1. Connect the BNC cable
to the Video connector
attached on your camera.
2. Connect the BNC cable
to the Video Input on a
monitor.
3. Connect the power adapter
to the Power connector
attached on your camera.
When the monitor is turned
on, the camera image
appears.
To adjust the lens focus, zoom, and function settings
1. Remove the Cover dome and Inner cover. For more details about the removing procedures,
see “Installation procedure,” in the Installing camera section on the next page.
2. Adjust the focus, zoom, and function settings of your camera using the Focus lever, Zoom
lever, and Switch board while you are viewing the image on the screen.
3. If you want to fix the adjusted focus and zoom, screw up the levers.
BNC Cable
Monitor
AB68-00649E(01)Eng.indd 11 2007-05-14 ｿﾀﾈﾄ 7:55:53

12
13
❚ Installing camera
Before installation
Before installing your camera, you have to read the following cautions:

You have to check whether the location (ceiling or wall) can bear five times the weight of your camera.

Don’t let the cable to be caught in improper place or the electric line cover to be damaged. Otherwise
it may cause a breakdown or fire. You can use wall mount adaptor (SADT-102WM), and pole mount
adaptor (SADT-100PM) for installing the camera on the wall or pipeline.

When installing your camera, don’t allow any person to approach the installation site. If you have any
valuable things under the place, move them away.
About the installation holes
A: Use these holes when directly installing your camera
on the ceiling or wall.
 While those are not used, fill in the holes using the
screw machine (M5 X L6.) for waterproofing.
B: Use four holes when directly installing your camera
on the junction box
 You can use the 4 1/8 diameter round type junction
box for assembly. (The junction box, gasket, and
cover are separately purchased items.)
C: Use these holes when installing the wall mount
adapter (SADT-102WM)
 While those are not used, fill in the holes using the
screw machine (M5 X L6.) for waterproofing.
The holes that are not used should be tightly
sealed up using the screws provided for
waterproofing. When the screws don’t have
rubber rings inside or are not closely attached,
note that it can cause waterproofing problem.
For attaching screws, see page 16
“Disassembling/assembling the Main body from
the Case.”
C
B
A
Bottom of camera
AB68-00649E(01)Eng.indd 12 2007-05-14 ｿﾀﾈﾄ 7:55:53

12
ENG
13
Installing on a pipe
Before installation, you have to be familiar with the above cautions and fill in the holes that are
not used for installation.
To install your camera bottom on a pipe
1. After connecting the power and video
cables, throw them inside the pipeline
and screw the male thread pipe into
the female pipe thread in your camera
tightly to fix the Main body. (In this case,
be sure to tape with Teflon tape before
assembly for waterproofing. Be careful
for the wiring cable not to be stuck in the
connection area.)
2. Adjust the angle of the camera in search
of a better view.
1) Separate the Dome cover using the
L-Wrench provided. (To make loose the
screws, rotate counterclockwise.)
2) Adjust the lens direction. For more
information, see page 17 “Adjusting the
camera direction.”
3. Attach the Dome cover. (Screw the
connection bolts tightly using the
L-Wrench for waterproofing.)
 To change the SAMSUNG logo position,
move the location of the connection
rubber band as show below and rotate
for assembly. (The rotation limit is 180
degree.)
AB68-00649E(01)Eng.indd 13 2007-05-14 ｿﾀﾈﾄ 7:55:54

14
15
To install the camera side on a pipe
1. Pull the power and video cables through
the pipe connection hole on the camera
side
1) Remove the side cover from the Case
using a coin or minus (-) driver. (Rotate
counterclockwise.)
2) Push the power and video cables
stretched outside of the bottom hole
into the Case. And pull them out from
the side cover of the Case.
2. Attach the removed side cover to the
bottom hole and rotate it clockwise using
a coin or minus (-) driver. (Be sure to
insert the O-ring (P22 T2.4) into the hole
before assembly. The ring is necessary
for waterproofing.)
3. After pulling the power and video cables
through the connection pipe, screw the
male thread pipe into the female pipe
thread in your camera tightly to fix the
Main body. (In this case, be sure to tape
with Teflon tape before assembly for
waterproofing. Be careful for the wiring
cable not to be stuck in the connection
area.)
4. Adjust the lens direction. For more
information, see page 17, “Adjusting the
camera direction.”
5. Attach the Dome cover. For more
information, see step 3 in “To install your
camera bottom on a pipe” on page 13.
AB68-00649E(01)Eng.indd 14 2007-05-14 ｿﾀﾈﾄ 7:55:54

14
ENG
15
Installing the camera on the ceiling
Before installation, you have to be familiar with the above cautions and fill in the holes that are
not used for installation.
To install your camera bottom on a pipe
1. Attach the provided template to the place
to be installed and penetrate a hole (5mm
diameter, minimum depth 35mm) for fixing
your camera to insert the provided plastic
anchor (HUD 5) to the full.
2. After connecting both power and video
cables, put them in order not to have
damage during installation.
3. Remove the Dome cover. For more
information, see step 2 in “To install your
camera bottom on a pipe” on page 13.
4. Install your camera. After aligning the hole
where the plastic anchor is inserted with
the camera installation hole, make tight
four ASSY screw-tappings where O-rings
are inserted. (If no O-rings are inserted,
water leak may happen.)
5. Adjust the camera lens direction. For
more information, see page 17, “Adjusting
the camera direction.”
6. Attach the Dome cover. For more
information, see step 3 in “To install your
camera bottom on a pipe” on page 13.
In case of wiring after penetrating
a hole on the installation site
1 Penetrate a wiring hole toward the
pipe. (Recommended hole size: within
30mm diameter)
2 Attach the gasket on the bottom of the
product as shown below. You have to
correctly align the hole with the pipe
hole.
 If the hole deviates from the gasket,
water leak may happen.
Gasket
AB68-00649E(01)Eng.indd 15 2007-05-14 ｿﾀﾈﾄ 7:55:54

16
17
Disassembling/assembling the Main body from the Case
The holes that are not used should be tightly sealed up using the screws provided for
waterproofing. To detach the Main body from the Case, follow the instructions below:
1. 1. Remove the Dome cover first.
2. Detach the Main body of the camera
from the Case.
1) Make loose two screws by rotating
counterclockwise.
2) Detach the Main body of the camera
after unlocking by pulling the left and
right levers in the arrow direction.
3. Assemble the Main body of the camera
with the Case. (Align three alignment
grooves of the Main body with the bumps
of the Case and assemble them.)
4. Attach the Dome cover using the
L-Wrench. For more information, see step
3 in “To install your camera bottom on a
pipe” on page 13.
1)
2)
AB68-00649E(01)Eng.indd 16 2007-05-14 ｿﾀﾈﾄ 7:55:55

16
ENG
17
❚ Adjusting the camera direction
When the camera is fixed on the ceiling, you can
adjust the camera viewing angle. You can rotate
your camera leftward or rightward (Panning), and
can change the slope of your camera upward or
downward (Tilting).
In case of panning, the rotation limit of your camera
is set to 355 degree (100 degree clockwise and 255
degree counterclockwise). The rotation is stopped
by the Stopper inside of the camera. For panning
control, first unfasten two screws located on the
bottom and rotate in the direction you want, and then
fasten them to fix the camera.
In case of tilting, you can change the slope of your
camera from zero to 90 degree. However if the slope
angle is under 17 degree, you can encounter a partial image hide problem. To fix the location
after adjusting the tilting angle, use the Tilt fixing screws.
To adjust the focus and zoom of your camera, use the Zoom lever and Focus lever. When you
install the camera on the inclined ceiling or wall, you can rotate the camera lens to see a correct
direction image.
Panning
Tilting
Lens rotation
AB68-00649E(01)Eng.indd 17 2007-05-14 ｿﾀﾈﾄ 7:55:57

18
19
SCC-B539X
AB68-00649E(01)Eng.indd 18 2007-05-14 ｿﾀﾈﾄ 8:48:30

18
ENG
19
Appendix A: Specifications for NTSC Standard
Item Details
Product type CCTV color dome camera
Power input AC 24V ± 10% (60Hz ± 0.3 Hz), DC 12V +10%/-5%
Broadcast type NTSC Standard System (525 Lines, 60 Fields)
Power consumption Approx. 1.7W
Image device 1/3 inch IT Type Super-HAD CCD
Pixels Total: 811(H) x 508(V), 410,000 pixels
Effective: 768(H) x 494(V), 380,000 pixels
Scanning mode 525 Lines, 2:1 Interlace
Scanning line frequency Horizontal: 15.734Hz(INT)/15.750Hz(LL)
Vertical: 59.94Hz(INT)/60Hz(LL)
Synchronization mode INT/Line Lock (Adjusting the phase using INC/DEC button)
Horizontal resolution 540 TV Lines
Min. object illumination
SCC-B53X3 (Color/BW) SCC-B53X2 (Color/BW)
F1.2
Sens-up Off
50IRE 0.4/0.04Lux 0.4/0.4Lux
30IRE 0.24/0.024Lux 0.24/0.24Lux
15IRE 0.12/0.012Lux 0.12/0.12Lux
Sens-up x128
50IRE 0.0031/0.00031Lux 0.0031/0.0031Lux
30IRE 0.0019/0.00019Lux 0.0019/0.0019Lux
15IRE 0.0009/0.00009Lux 0.0009/0.0009Lux
Signal output COMPOSITE Video(1 . 0 Vp-p, 75ohm, BNC), Test Monitor OUT(1 . 0 Vp-p, 75ohm, Harness cable)
Lens Auto Iris (DC)
Focal length: 2.5 to 6.0mm
Aperture ratio: 1.2
PAN function Range: 0 to 355° (100 degree clockwise and 255 degree counterclockwise)
TILT function Range: 0 to 90°
Controls
Line Lock (LL)
Sens-Up; Low Speed Shutter(LSS)
Horizontal Reverse (H-REV)
Vertical Reverse (V-REV)
Backlight compensation (BLC)
Flickerless (FL)
Switching between color and B&W modes (D/N)
Auto white balancing (AWB)
Digital noise reduction (DNR)
Dynamic CCD defect compensation
Operation temperature -10°C to +50°C
Operation humidity Up to 90%
Size 150(Ø) x 121(H)mm
Weight SCC-B539X: 1.1kg
AB68-00649E(01)Eng.indd 19 2007-05-14 ｿﾀﾈﾄ 7:55:59

20
Appendix B: Specifications for PAL Standard
Item Details
Product type CCTV color dome camera
Power input AC 24V ± 10% (50Hz ± 0,3 Hz), DC 12V +10%/-5%
Broadcast type PAL Standard System (625 Lines, 50 Fields)
Power consumption Approx. 1,7W
Image device 1/3 inch IT Type Super-HAD CCD
Pixels Total: 795(H) x 596(V), 470,000 pixels
Effective: 752(H) x 582(V), 440,000 pixels
Scanning mode 625 Lines, 2:1 Interlace
Scanning line frequency Horizontal: 15,625Hz(INT)/15,625Hz(LL)
Vertical: 50Hz(INT)/50Hz(LL)
Synchronization mode INT/Line Lock (Adjusting the phase using INC/DEC button)
Horizontal resolution 540 TV Lines
Min. object illumination
SCC-B53X3 (Color/BW) SCC-B53X2 (Color/BW)
F1,2
Sens-up Off
50IRE 0,4/0,04Lux 0,4/0,4Lux
30IRE 0,24/0,024Lux 0,24/0,24Lux
15IRE 0,12/0,012Lux 0,12/0,12Lux
Sens-up x128
50IRE 0,0031/0,00031Lux 0,0031/0,0031Lux
30IRE 0,0019/0,00019Lux 0,0019/0,0019Lux
15IRE 0,0009/0,00009Lux 0,0009/0,0009Lux
Signal output COMPOSITE Video(1,0 Vp-p, 75ohm, BNC), Test Monitor OUT(1,0 Vp-p, 75ohm, Harness cable)
Lens Auto Iris (DC) Focal length: 2,5 to 6,0mm
Aperture ratio: 1,2
PAN function Range: 0 to 355° (100 degree clockwise and 255 degree counterclockwise)
TILT function Range: 0 to 90°
Controls
Line Lock (LL)
Sens-Up; Low Speed Shutter(LSS)
Horizontal Reverse (H-REV)
Vertical Reverse (V-REV)
Backlight compensation (BLC)
Flickerless (FL)
Switching between color and B&W modes (D/N)
Auto white balancing (AWB)
Digital noise reduction (DNR)
Dynamic CCD defect compensation
Operation temperature -10°C to +50°C
Operation humidity Up to 90%
Size 150(Ø) x 121(H)mm
Weight SCC-B539X: 1,1kg
AB68-00649E(01)Eng.indd 20 2007-05-14 ｿﾀﾈﾄ 7:55:59