Samsung SNO-7080R User manual

NETWORK CAMERA
User Manual SNO-7080R

Copyright
©2012 Samsung Techwin Co., Ltd. All rights reserved.
Trademark
is the registered logo of Samsung Techwin Co., Ltd.
The name of this product is the registered trademark of Samsung Techwin Co., Ltd.
Other trademarks mentioned in this manual are the registered trademark of their respective company.
Restriction
Samsung Techwin Co., Ltd shall reserve the copyright of this document. Under no circumstances, this document shall
be reproduced, distributed or changed, partially or wholly, without formal authorization of Samsung Techwin.
Disclaimer
Samsung Techwin makes the best to verify the integrity and correctness of the contents in this document, but no
formal guarantee shall be provided. Use of this document and the subsequent results shall be entirely on the user’s own
responsibility. Samsung Techwin reserves the right to change the contents of this document without prior notice.
Design and specifications are subject to change without prior notice.
The default password can be exposed to a hacking thread so it is recommended to change the password
after installing the product.
Note that the security and other related issues caused by the unchanged password shall be responsible
for the user.
Network Camera
User Manual

English _3
●OVERVIEW
IMPORTANT SAFETY INSTRUCTIONS
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings, Install in accordance with the manufacturer’s
instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized
plug has two blades with one wider than the other. A grounding type plug has two
blades and a third grounding prong. The wide blade or the third prong are provided for
your safety. If the provided plug does not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs,
convenience receptacles, and the point where they exit from the apparatus.
11. Only use attachments/ accessories specified by the manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table specified by
the manufacturer, or sold with the apparatus. When a cart is used,
use caution when moving the cart/apparatus combination to avoid
injury from tip-over.
13. Unplug this apparatus during lighting storms or when unused for
long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required when the
apparatus has been damaged in any way, such as power-supply cord or plug is
damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus
has been exposed to rain or moisture, does not operate normally, or has been dropped.
overview

overview
4_ overview
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE
THIS PRODUCT TO RAIN OR MOISTURE. DO NOT INSERT ANY METALLIC
OBJECT THROUGH THE VENTILATION GRILLS OR OTHER OPENNINGS
ON THE EQUIPMENT.
Apparatus shall not be exposed to dripping or splashing and that no objects
filled with liquids, such as vases, shall be placed on the apparatus.
To prevent injury, this apparatus must be securely attached to the Wall/ceiling
in accordance with the installation instructions.
CAUTION
CAUTION
RISK OF ELECTRIC SHOCK.
DO NOT OPEN
CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK.
DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
EXPLANATION OF GRAPHICAL SYMBOLS
The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert the user to the
presence of “dangerous voltage” within the product’s
enclosure that may be of sufficient magnitude to constitute a
risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended
to alert the user to the presence of important operating
and maintenance (servicing) instructions in the literature
accompanying the product.

English _5
●OVERVIEW
Battery
Batteries(battery pack or batteries installed) shall not be exposed to excessive
heat such as sunshine, fire or the like.
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
Disconnection Device
Disconnect the main plug from the apparatus, if it’s defected. And please call
a repair man in your location.
When used outside of the U.S., it may be used HAR code with fittings of
an approved agency is employed.
CAUTION
These servicing instructions are for use by qualified service personnel only.
To reduce the risk of electric shock do not perform any servicing other than
that contained in the operating instructions unless you are qualified to do so.
The BNC Out terminal of the product is provided for easier installation, and is
not recommended for monitoring purposes.
If you keep the BNC cable connected, a risk of lightening may cause damage
or malfunction to the product.
Please use the input power with just one camera and other devices must not
be connected.

overview
6_ overview
Please read the following recommend safety precautions carefully.
Do not place this apparatus on an uneven surface.
Do not install on a surface where it is exposed to direct sunlight, near
heating equipment or heavy cold area.
Do not place this apparatus near conductive material.
Do not attempt to service this apparatus yourself.
Do not place a glass of water on the product.
Do not install near any magnetic sources.
Do not block any ventilation openings.
Do not place heavy items on the product.
Do not expose the camera to radioactivity.
User’s Manual is a guidance book for how to use the products.
The meaning of the symbols are shown below.
Reference : In case of providing information for helping of product’s usages
Notice : If there’s any possibility to occur any damages for the goods and
human caused by not following the instruction
Please read this manual for the safety before using of goods and keep it in
the safe place.

English _7
●OVERVIEW
CONTENTS
OVERVIEW
3
3Important Safety Instructions
9Product Features
10 Recomended PC Specifications
10 Recomended SD/SDHC Memory
Card Specifications
11 What’s Included
12 At a Glance
INSTALLATION &
CONNECTION
15
15 Memory Card Information
15 Connecting with other Device
NETWORK CONNECTION
AND SETUP
19
19 Connecting the Camera Directly
to Local Area Networking
20 Connecting the Camera Directly
to a DHCP Based DSL/Cable
Modem
21 Connecting the Camera Directly
to a PPPoE Modem
22 Connecting the Camera to a
Broadband Router with the
PPPoE/Cable Modem
23 Buttons used in IP Installer
24 Static IP Setup
28 Dynamic IP Setup
29 Port Range Forward (Port Mapping)
Setup
31 Connecting to the Camera from a
Shared Local PC
31 Connecting to the Camera from a
Remote PC via the Internet

overview
8_ overview
SETUP SCREEN
42
42 Setup
42 Audio & Video Setup
53 Network Setup
60 Event Setup
72 System Setup
APPENDIX
77
77 Specification
81 Product Overview
82 Troubleshooting
84 Open Source Announcement
85 License
88 GPL/LGPL Software License
WEB VIEWER
32
32 Connecting to the Camera
33 Login
34 Installing ActiveX
35 Installing Silverlight Runtime
37 Using the Live Screen
40 Playback

English _9
●OVERVIEW
PRODUCT FEATURES
• Dustproof/Waterproof (IP66)
The dustproof and waterproof design makes you feel at ease when installing the product
outdoors or exposing it to rain.
• SSNR3 (Samsung Super Noise Reduction)
The powerful DSP chip reduces the gain noise effectively to remove the time lag so that it
can provide a sharp and clear image in a low contrast scene.
• Day & Night (ICR)
It automatically detects the time change of the day to switch to a mode that is appropriate
to the current scene. In a daylight scene, it switches to the color mode for maintaining
the optimal color tones while it, at night, switches to B/W mode for identifying the low
contrast scene.
• IR mode
If the IR indicator turns on, the product switches to the IR mode for preventing an object
from being too bright, which helps you identify the object in near distance.
• Visibility: 30m
In B/W mode, the IR indicator turns on with the effective visibility of 30m at 0 Lux.
• SSDR (Samsung Super Dynamic Range)
For a scene showing a great contrast difference such as backlight scene, the product
maintains the bright areas while selectively making the dark areas brighter to balance the
overall contrast.
• Others
Other features include: HLC (High Light Compensation), SENS-UP, V-REV, H-REV,
D-ZOOM, SHARPNESS, Motion Detection, PRIVACY.
• Full HD Video Quality
• Multi-Streaming
This network camera can display videos in different resolutions and qualities
simultaneously using different CODECs.
• Web Browser-based Monitoring
Using the Internet web browser to display the image in a local network environment.
• Alarm
If an event occurs, the event-related video will be transferred to the email specified by the
user or the event signal will be sent to the Alarm Out port.
• Built-in SD Memory
This product is equipped with an internal 4GB memory card.

overview
10_ overview
• Video Motion Detection
Detects a motion from the video before triggering an event.
• Face Detection / Smart Codec
Recognizes a face from the camera input video, or transfers a clearer image of your specified area.
• Auto Detection of Disconnected Network
Detects network disconnection before triggering an event.
• ONVIF Compliance
This product supports ONVIF.
For more information, refer to www.onvif.org.
RECOMENDED PC SPECIFICATIONS
•CPU : Intel Core 2 Duo 2.4GHz or higher
•Operating System : Windows XP, VISTA, 7
Mac OS
•Resolution : 1280X1024 pixels or higher
•RAM : 2GB or higher
•Web Browser : Internet Explorer 7.0 or higher, Firefox, Chrome, Safari
Neither a beta test version unlike the version released in the company website nor the developer version will
be supported.
On Firefox v3.5 or higher, displaying warning message dialog may cause an error.
If connecting to IPv6 in Windows XP, it can cause some problem.
It is recommended to connect to IPv6 in Windows 7.
•Video Memory : 256MB or higher
J
If the driver of the video graphic adapter is not installed properly or is not the latest version, the
video may not be played properly.
RECOMENDED SD/SDHC MEMORY CARD
SPECIFICATIONS
•2GB ~ 32GB
•To ensure proper recording of video data, it is recommended you use a memory card that
supports at least read/write speed 10Mbps and Class 6.

English _11
●OVERVIEW
WHAT’S INCLUDED
Please check if your camera and accessories are all included in the product package.
Appearance Item Name Quantity Description
Camera 1
User Manual,
Installer S/W CD,
CMS S/W DVD
2
Quick Guide 1
Tapping Screw 3 Used for installation on the wall or ceiling
L Wrench 1Used to adjust the camera orientation
Sunshield 1 It protects the camera from the direct
sunlight.
Sunshield Hold 1 It fixes the sunshield with the camera.

overview
12_ overview
AT A GLANCE
Front Side
Item Description

Sunshield It protects the camera from the direct sunlight.
b
Sunshield Hold It fixes the sunshield with the camera.
c
IR LED These infrared LED's are controlled by the illumination sensor.

Illumination Sensor Detects incoming light to control the IR LED.
M
Wipe out a dirty surface of the lens softly with a lens tissue or cloth to which you have applied
ethanol.

English _13
●OVERVIEW
Rear Side
Item Description

Power Port Used to plug the power cable.
b
Network Port Used to connect a PoE or LAN cable.
c
Video Output Port Connected to the monitor so that you can check the video from the camera.
(for installation)

Audio In Jack Used to connect to a microphone.

Audio Out Jack Used to connect to speakers.
ARM-IN
GND
ARM-OUT
A-COM
RESET
RESET

overview
14_ overview
Item Description

I/O Port
ARM-IN Used to connect the alarm input sensor.
GND Earth-grounding port for external signal.
ARM-OUT Used to connect the alarm output signal.
A-COM Common port where the alarm output signal is
connected.
RESET
Resets the camera settings to the default.
Peel off two red lines and contact them for about
10 seconds to reset the product.

English _15
●INSTALLATION & CONNECTION
MEMORY CARD INFORMATION
What is a memory card?
The memory card is an external data storage device that has been developed to offer an
entirely new way to record and share video, audio, and text data using digital devices.
Memory Card Instructions
•This product is equipped with an internal 4GB memory card.
Do not dismantle this product by yourself for a reason such as waterproofing.
•If you encounter a problem with the installation, contact the manufacturer for
technical assistance.
CONNECTING WITH OTHER DEVICE
installation & connection
ARM-IN
GND
ARM-OUT
A-COM
RESET
RESET
Power
Ethernet
Monitor (for installation)

installation & connection
16_ installation & connection
Connecting to the monitor
Use the BNC cable to connect the video output port of the camera with the video input
port of the monitor.
M
In the initial installation of the camera, you can connect the camera to the monitor for checking
the connection status.
You can set the video output type to either NTSC or PAL. (page 44).
J
The BNC Out terminal of the product is provided for easier installation, and is not recommended
for monitoring purposes.
If you keep the BNC cable connected, a risk of lightening may cause damage or malfunction to
the product.
Ethernet Connection
Connect the Ethernet cable to the local network or to the Internet.
Power Supply
Use the screwdriver to connect each line (+, –) of the power cable to the corresponding
power port of the camera.
J
Be careful not to reverse the polarity when you connect the power cable.
You can also use a router featuring PoE (Power over Ethernet) to supply power to the camera.
If both PoE and DC 12V are supplied, the product will operate with the first-applied power source.
If using PoE and DC 12V, the heater will not operate at all.
The heater will operate properly only by the power source of AC 24V. The adaptor is sold
separately.
AC 24V can be applied in non-polarity.
Use AC 24V in a low-temperature place of less than -10°C.
Please make sure the monitor and camera are turned off when connecting them.

English _17
●INSTALLATION & CONNECTION
Connecting to Audio Input/Output
1. Connect the AUDIO IN port of the camera with the microphone directly or LINE OUT
port of the amplifier that the microphone is connected to.
2. Connect the AUDIO OUT port of the camera with the LINE IN port of the speaker.
3. Check the specifications for audio input.
• Audio Codec
G.711 PCM. μ-law 64kbps 8kHz sampling
• Full duplex Audio
• Audio in
Used for mono signal line input (Max.2.4 Vpp)
• Audio out
Used for mono signal line output (Max.2.4 Vpp)
• Line out impedance
600
ARM-IN
GND
ARM-OUT
A-COM
RESET
RESET
PC
Speaker
Microphone
Amp
Amp
Microphone
Microphone
Speaker
Network

installation & connection
18_ installation & connection
Connecting the alarm I/O signal
Connect the alarm input/output signal using the I/O ports of the cable.
Port Description Port Description
ARM-IN Alarm Input Sensor Port GND Earth-grounding Port
ARM-OUT Alarm out A-COM Alarm Out (common)
To connect the alarm input signal
Connect one strand of each signal line (2-strand) of the sensors to the [ARM-IN] port, and
connect the other strand to the [GND] port.
To connect the alarm output signal
Connect one strand of each signal line (2-strand) of an external device to the [ARM-OUT]
port, and connect the other stand to the [A-COM] port.
ARM-IN
GND
ARM-OUT
A-COM
RESET
RESET
ARM-IN
GND
ARM-OUT
A-COM
RESET
RESET
ALARM SENSOR

English _19
●
NETWORK CONNECTION AND SETUP
You can set up the network settings according to your network configurations.
CONNECTING THE CAMERA DIRECTLY TO LOCAL AREA
NETWORKING
Connecting to the camera from a local PC in the LAN
1. Launch an Internet browser on the local PC.
2. Enter the IP address of the camera in the address bar of the browser.
M
A remote PC in an external Internet out of the LAN network may not be able to connect to the
camera installed in the intranet if the port-forwarding is not properly set or a firewall is set.
In this case, to resolve the problem, contact your network administrator.
By factory default, the IP address will be assigned from the DHCP server automatically. If there is
no DHCP server available, the IP address will be set to 192.168.1.100.
To change the IP address, use the IP Installer.
For further details on IP Installer use, refer to “Static IP Setup”. (Page 24)
network connection and setup
Switch
Camera
Camera
Local PC
Firewall External Remote PC
DDNS Server
(Data Center, KOREA)
INTERNET
<Local Network>

20_ network connection and setup
network connection and setup
CONNECTING THE CAMERA DIRECTLY TO A DHCP
BASED DSL/CABLE MODEM
1. Use the cross LAN cable to connect the network cable directly to your PC.
2. Run the IP Installer and change the IP address of the camera so that you can use
the web browser on your desktop to connect to the Internet.
3. Use the Internet browser to connect to the camera.
4. Move to [Setup] page.
5. Move to [Network] – [DDNS] and configure the DDNS settings.
6. Move to [Network] – [Interface], and set the IP type to [DHCP].
7. Connect the camera, which was removed from your PC, directly to the modem.
8. Restart the camera.
M
For registering the DDNS settings, refer to “Registering with DDNS”. (page 55)
For configuring the DDNS settings, refer to “DDNS”. (page 54)
For setting the IP type, refer to “Interface”. (page 53)
Camera
External Remote PC
DDNS Server
(Data Center, KOREA)
DSL/Cable
Modem
INTERNET