Samsung HW-S60T Installation instructions

FULL MANUAL

SAFETY
INFORMATION
SAFETY WARNINGS
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT
REMOVE THE COVER (OR BACK).
NO USER-SERVICEABLE PARTS ARE INSIDE.
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
Refer to the table below for an explanation of
symbols which may be on your Samsung product.
CAUTION
RISK OF ELECTRIC SHOCK.
DO NOT OPEN.
This symbol indicates that high voltage is
present inside. It is dangerous to make
any kind of contact with any internal part
of this product.
This symbol indicates that this product
has included important literature
concerning operation and maintenance.
Class II product : This symbol indicates
that it does not require a safety
connection to electrical earth (ground). If
this symbol is not present on a product
with a power cord, the product MUST
have a reliable connection to protective
earth (ground).
AC voltage : This symbol indicates that
the rated voltage marked with the
symbol is AC voltage.
DC voltage : This symbol indicates that
the rated voltage marked with the
symbol is DC voltage.
Caution, Consult instructions for use :
This symbol instructs the user to consult
the user manual for further safety
related information.
WARNING
• To reduce the risk of fire or electric shock, do
not expose this appliance to rain or moisture.
CAUTION
•TO PREVENT ELECTRIC SHOCK, MATCH WIDE
BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.
•This apparatus shall always be connected to a
AC outlet with a protective grounding
connection.
•To disconnect the apparatus from the mains,
the plug must be pulled out from the mains
socket, therefore the mains plug shall be
readily operable.
•Do not expose this apparatus to dripping or
splashing. Do not put objects filled with
liquids, such as vases on the apparatus.
•To turn this apparatus off completely, you
must pull the power plug out of the wall
socket. Consequently, the power plug must be
easily and readily accessible at all times.
PRECAUTIONS
1. Ensure that the AC power supply in your
house complies with the power requirements
listed on the identification sticker located on
the bottom of your product. Install your
product horizontally, on a suitable base
(furniture), with enough space around it for
ventilation (7~10 cm). Make sure the
ventilation slots are not covered. Do not place
the unit on amplifiers or other equipment
which may become hot. This unit is designed

ENG - 3
for continuous use. To fully turn off the unit,
disconnect the AC plug from the wall outlet.
Unplug the unit if you intend to leave it
unused for a long period of time.
2. During thunderstorms, disconnect the AC
plug from the wall outlet. Voltage peaks due
to lightning could damage the unit.
3. Do not expose the unit to direct sunlight or
other heat sources. This could lead to
overheating and cause the unit to
malfunction.
4. Protect the product from moisture (i.e.
vases), and excess heat (e.g. a fireplace) or
equipment creating strong magnetic or
electric fields. Unplug the power cable from
the AC wall socket if the unit malfunctions.
Your product is not intended for industrial
use. It is for personal use only. Condensation
may occur if your product has been stored in
cold temperatures. If transporting the unit
during the winter, wait approximately 2
hours until the unit has reached room
temperature before using.
5. The battery used with this product contains
chemicals that are harmful to the
environment. Do not dispose of the battery in
the general household trash. Do not expose
the battery to excess heat, direct sunlight, or
fire. Do not short circuit, disassemble, or
overheat the battery. Danger of explosion if
the battery is replaced incorrectly. Replace
only with the same or equivalent type.

ENG - 4
Fabric cleaning
Remove any dirt or stain on the product surface
immediately.
Removing and cleaning can be less effective for
some substances or if left for a prolonged time.
CAUTION
•Use a vacuum cleaner or an adhesive lint roller
to remove dust, handprints, and the likes.
–Some cleaning brushes may damage the
product, depending on the materials they
contain.
–Towels and cleaning clothes may leave lint
or dirt on the product.
•Do not use a nail or other tools to scratch the
dirt off. It may damage the fabric.
•To remove oil or liquid stains, use a clean
white cloth moist with water. If the stain
persists, wipe it with a mixture of water and
neutral detergent (such as dishwashing soaps)
and a cloth.
–A non-neutral detergent or cleaner may
cause discolouration or fabric damage.
–After cleaning, use a dry cloth or hairdryer
to dry the area.
–Do not use excessive force to avoid
discolouration or fabric damage.
CONTENTS
01 Checking the Components-------------------------------------------------6
Inserting Batteries before using the Remote Control (AA batteries X 2) ----------------------------- 6
02 Product Overview------------------------------------------------------------7
Top Panel of the Soundbar-------------------------------------------------------------------------------------- 7
Bottom Panel of the Soundbar--------------------------------------------------------------------------------- 9
03 Using the Remote Control -----------------------------------------------10
How to Use the Remote Control----------------------------------------------------------------------------- 10
Output specifications for the different sound effect modes ------------------------------------------ 12
Adjusting the Soundbar volume with a TV remote control-------------------------------------------- 14
04 Connecting the Soundbar------------------------------------------------14
Connecting Electrical Power ---------------------------------------------------------------------------------- 14
Connecting an SWA-8500S (Sold Separately) to your Soundbar ------------------------------------- 15
Connecting an SWA-W500 (Sold Separately) to your Soundbar-------------------------------------- 16
05 Using a wired connection to the TV-----------------------------------19

ENG - 5
Method 1. Connecting with HDMI--------------------------------------------------------------------------- 19
Method 2. Connecting using an Optical Cable------------------------------------------------------------ 21
06 Using a wireless connection to the TV -------------------------------22
Method 1. Connecting via Bluetooth ---------------------------------------------------------------------- 22
Method 2. Connecting via Wi-Fi ----------------------------------------------------------------------------- 23
07 Connecting an External Device -----------------------------------------24
Connecting using an Optical Cable -------------------------------------------------------------------------- 24
08 Connecting a Mobile Device --------------------------------------------24
Method 1. Connecting via Bluetooth ----------------------------------------------------------------------- 24
Method 2. Connecting via Wi-Fi (Wireless Network) --------------------------------------------------- 27
Configuring Amazon Alexa ------------------------------------------------------------------------------------ 28
Using the Tap Sound-------------------------------------------------------------------------------------------- 31
09 Installing the Wall Mount------------------------------------------------32
Installation Precautions---------------------------------------------------------------------------------------- 32
Wallmount Components--------------------------------------------------------------------------------------- 32
10 Installing the Soundbar in front of TV---------------------------------34
11 Software Update -----------------------------------------------------------34
Auto Update------------------------------------------------------------------------------------------------------ 34
USB Update------------------------------------------------------------------------------------------------------- 34
Initialisation ------------------------------------------------------------------------------------------------------ 35
12 Troubleshooting ------------------------------------------------------------ 35
13 Licence ------------------------------------------------------------------------ 37
14 Open Source Licence Notice---------------------------------------------38
15 Important Notes About Service-----------------------------------------38

ENG - 6
16 Specifications and Guide --------------------------------------------------38
Specifications----------------------------------------------------------------------------------------------------- 38
01 CHECKING THE COMPONENTS
•For more information about the power supply and power consumption, refer to the label attached
to the product. (Label: Bottom of the Soundbar Main Unit)
•To purchase additional components or optional cables, contact a Samsung Service Centre or
Samsung Customer Care.
•For more information about the wallmount see page 36.
•Design, specifications, and App screen are subject to change without prior notice.
•The appearance of the accessories may differ slightly from the illustrations above.
Inserting Batteries before using the Remote Control (AA batteries X
2)
Slide the back cover in the direction of the arrow until
it is completely removed. Insert 2 AA batteries (1.5V)
oriented so that their polarity is correct. Slide the back
cover back into position.

ENG - 7
02 PRODUCT OVERVIEW
Top Panel of the Soundbar
LED
indicator
The LED Indicator flashes, glows, or changes colour depending on the Soundbar's current
mode or status. The colour of the LED indicator and the number of lights indicate the active
mode as described below.
W
White LED
W
White LED
M
Multicolour LED
W
White LED
W
White LED
• The Multicolour LED changes to White, Cyan, Green, Red, and Blue depending on the
mode or status.
Multi
Function
Button
•In standby mode, press the (Multi Function) button to turn on the Soundbar.
•Press the (Multi Function) button to change the mode. Each time you change
the mode, the LED lights in white and then turns off.
LED
Indicator
“Digital Audio In” or
“TV ARC”
“Wi-Fi”
“Bluetooth”
•Press the (Multi Function) button for 3 seconds to call Alexa. Say with the
button pressed to enable voice recognition.
Volume
Button
Press the (Volume) button to adjust the volume.

ENG - 8
•When you plug in the AC cord, the power button will begin working in 4 to 6 seconds.
•When you turn on this unit, there will be a 4 to 5 second delay before it produces sound.
•If you hear sounds from both the TV and Soundbar, go to the Settings menu for the TV audio and
change the TV speaker to External Speaker.
•You can turn on and off audio feedback by using SmartThings app. To learn about using the
SmartThings app, refer to “Method 2. Connecting via Wi-Fi (Wireless Network)”.

ENG - 9
Bottom Panel of the Soundbar
ID SET
Press to connect the Soundbar to Surround speakers and a subwoofer wirelessly.
(The surround speaker, subwoofer are sold separately.)
NETWORK
Press to connect to a wireless network (Wi-Fi) via the SmartThings app.
SERVICE
Connect a USB storage device to upgrade the product's software.
DC 19V (Power Supply In)
Connect the AC/DC power adapter. (See page 16)
DIGITAL AUDIO IN (OPTICAL)
Connect to the digital (optical) output of an external device. (See page 27)
HDMI (ARC)
Connect to the HDMI jack on a TV. (See page 21)
•When disconnecting the power cable of the AC/DC power adaptor from a wall outlet, pull the plug.
Do not pull the cable.
•Do not connect this unit or other components to an AC outlet until all connections between
components are complete.

ENG - 10
03 USING THE REMOTE CONTROL
How to Use the Remote Control
Power
Turns the Soundbar on and off.
LED
Indicator
On
Off
• Auto Power Down Function
The unit turns off automatically in the following situations:
–In “Digital Audio In” or “TV ARC” / “Wi-Fi” /
“Bluetooth” mode if there is no audio signal for 18
minutes.
(Source)
Press to select a source connected to the Soundbar.
(Mute)
Press the (Mute) button to mute the sound.
Press it again to unmute the sound.
LED
Indicator

ENG - 11
SOUND MODE
By pressing the button, you can select the desired audio mode. Each time the mode changes, the
Multicolour LED blinks in white.
LED
Indicator
“Standard”“Music”“Adaptive Sound”
•Standard
Outputs the original sound.
•Music
Provides more natural and room filling sound for music content.
•Adaptive Sound
Analyzes the content in real time and automatically provides the optimal sound field based on the
characteristics of the content.
Bluetooth PAIR
Switch the Soundbar to Bluetooth pairing mode.
When you press the button, the LED display changes as shown below.
• Until pairing is complete, the Multicolour LED changes as Red → Green → Blue in turn.
LED
Indicator
Pairing
Connection is complete
“Ready to connect via Bluetooth.”
p(Play / Pause)
You can also play or pause music by pressing the button.
Up/Down/Left/Right
Press Up/Down/Left/Right on the button to select or set functions.
• Music Skip
Press the Right button to select the next music file. Press the Left button to select the previous music
file.

ENG - 12
(Sound Control)
By pressing the button, you can select the desired audio mode. The desired item can be adjusted using the
Up/Down buttons. Each time the mode changes, the Multicolour LED blinks in white.
LED
Indicator
“Treble”“Bass”“Sync”“Side Level”
–To control the volume of the treble or bass sound, select “Treble” or “Bass”in Sound Settings, and
then adjust the volume between -6~+6 by using the Up/Down buttons.
–Press and hold the (Sound Control) button for about 5 seconds to adjust the sound for
each frequency band. 150Hz, 300Hz, 600Hz, 1.2kHz, 2.5kHz, 5kHz, and 10kHz are selectable using the
Left/Right buttons and each can be adjusted to a setting between -6 to +6 using the Up/Down
buttons. (Make sure the Sound mode is set to “Standard”.)
–To control the volume of the each speaker select “Side Level”in Sound Settings, and then adjust the
volume between -6~+6 by using the Up/Down buttons.
–If the video on the TV and audio from the Soundbar are not synchronised, select “Sync” in Sound
Control, and then set the audio delay between 0~300 milliseconds by using the Up/Down buttons. –
“Sync” is only supported for some functions.
WOOFER (BASS) LEVEL
Push the button up or down to adjust the level of the woofer (bass) to -12 or between -6 to +6. To set the
woofer (bass) volume level to 0 (Default), press the button.
VOLUME
Push the button up or down to adjust the volume.
LED
Indicator
Output specificationsfor the different sound effect
modes
Effect
Input
Output
With Subwoofer Only
With Subwoofer & Wireless
Rear Speaker Kit
Standard
2.0 ch
2.1 ch
2.1 ch

ENG - 13
5.1 ch
2.1 ch
4.1 ch
Music
2.0 ch
4.1 ch
6.1 ch
5.1 ch
4.1 ch
6.1 ch
Adaptive Sound
2.0 ch
4.1 ch
6.1 ch
5.1 ch
4.1 ch
6.1 ch
• The Samsung Wireless Rear Speaker Kit, and Subwoofer can be purchased separately.
To purchase a Kit or the Subwoofer, contact the vendor you purchased the Soundbar from.

ENG - 14
Adjusting the Soundbar volume with a TV remote control
Adjust the Soundbar volume using the TV’s remote control.
•This function can be used with IR remote controls only. Bluetooth remote controls (remote
controls that require pairing) are not supported.
•Set the TV speaker to External Speaker to use this function.
•Manufacturers supporting this function:
VIZIO, LG, Sony, Sharp, PHILIPS, PANASONIC, TOSHIBA, Hisense, RCA
1. Turn Off the Soundbar.
2. Push up and hold the WOOFER button for 5 seconds.
Each time you push the WOOFER button up and hold it for 5 seconds, the mode switches in the
following order: “Samsung-TV Remote” (Default mode), “Off-TV Remote”, “All-TV Remote”.
The LED indicator status changes each time the mode is changed, as shown below.
Remote Control Button
LED Indicator
Status
"Samsung-TV Remote"
(Default mode)
Enable a Samsung TV’s IR remote
control.
"Off-TV Remote"
Disable the TV remote control.
"All-TV Remote"
Enable a third-party TV’s IR remote
control.
04 CONNECTING THE SOUNDBAR
Connecting Electrical Power
Use the power components to connect the Soundbar to an electrical outlet in the following order:
• For more information about the required electrical power and power consumption, refer to the label
attached to the product. (Label: Bottom of the Soundbar Main Unit)
1. First connect the power cable to the AC/DC adapter.

ENG - 15
Connect the AC/DC adapter (with the power cable) to the Soundbar.
2. Connect the power cord to a wall socket.
NOTES
•If you unplug and reconnect the power cord when the product is turned on, the Soundbar turns on
automatically.
•Make sure to rest the AC/DC Adapter flat on a table or the floor. If you place the AC/DC Adapter so
that it is hanging with the AC cord input facing upwards, water or other foreign substances could
enter the Adapter and cause the Adapter to malfunction.
Connecting an SWA-8500S (Sold Separately) to your Soundbar
Expand to true wireless surround sound by connecting the Samsung Wireless Rear Speaker Kit (SWA-
8500S, sold separately) to your Soundbar.
1. Connect the Wireless Receiver Module to 2 Surround Speakers. –The speaker cables are colour
coded.
2. Check the standby status of the Wireless Receiver Module after plugging it into an electrical outlet.
•The LINK LED indicator (blue) on the Wireless Receiver Module should be blinking. If the
indicator does not blink, use a narrow pin to press and hold the ID SET button for 5 seconds or
longer. See the SWA-8500S user guide for more details.
SERVICE
DC 19V
DIGITAL AUDIO IN
(
OPTICAL
)
SERVICE
DC 19V

ENG - 16
3. Press the Up button on the remote control for 5 seconds.
•Until pairing is complete, the Multicolour LED changes as Red → Green → Blue in turn.
Rear Speaker, Woofer Pairing button
LED Indicator
CAUTION
•If your Soundbar was playing music when it connects to the SWA-8500S, you may hear some
stuttering from the woofer as the connection finalises.
4. Check if the LINK LED is solid blue (connection complete).
The LINK LED indicator stops blinking and glows
a solid blue when a connection is established
between the Soundbar and the Wireless
Receiver Module.
5. If the SWA-8500S is not connected, repeat the procedure from Step 2.
Connecting an SWA-W500 (Sold Separately) to your Soundbar
1. Turn off the Soundbar by pressing the (Power) button on the remote control.
Pairing
STANDBY
LINK
NDBY
LINK

ENG - 17
2. Plug in the Wireless Subwoofer, and then check its standby status.
•Plug the Wireless Subwoofer power cord into an electrical outlet and into the Wireless
Subwoofer to turn on the Wireless Subwoofer. The LINK LED indicator (blue LED) on the Wireless
Subwoofer blinks. If the LED does not blink, press the ID SET button on the rear of the Wireless
Subwoofer with a pen tip for 5~6 seconds until the LINK LED indicator blinks (in Blue). For more
about the LED, please refer to the SWA-W500 user manual.
•The main unit is heavy. Be careful not to pinch your fingers when pressing the ID SET button or
connecting the power cord to the rear of the unit.
•The upper part of the subwoofer is prone to scratches. Handle it carefully.
•Do not press on or strike the
Speaker Unit on the bottom of the
body. You can deform or damage the
speaker.
3. Press the Up button on the
remote control for 5 seconds.
• Until pairing is complete, the
Multicolour LED changes as Red →
Green → Blue in turn.
Rear Speaker, Woofer Pairing button
LED Indicator

ENG - 18
4. Check if the LINK LED is solid blue (connection complete).
The LINK LED indicator stops blinking and
glows a solid blue when a connection is
established between the Soundbar and
the Wireless Subwoofer.
NOTES
–Do not connect the power cord of this product or your TV to a wall outlet until all connections
between components are complete.
–Before moving or installing this product, be sure to turn off the power and disconnect the power
cord.
–The maximum transmission distance of the wireless signal of the main unit is about 10 m, but may
vary depending on your operating environment. If a steel-concrete or metallic wall is between the
main unit and the wireless subwoofer, the system may not operate at all, because the wireless signal
cannot penetrate metal.
PRECAUTIONS
–Wireless receiving antennas are built into the wireless subwoofer. Keep the units away from water
and moisture.
–For optimal listening performance, make sure that the area around the wireless subwoofer and
Wireless Receiver Module (Sold separately) is clear of any obstructions.
Pairing

ENG - 19
05 USING A WIRED CONNECTION TO THE TV
Method 1. Connecting with HDMI
CAUTION
•When both the HDMI cable and optical cable are connected, the HDMI signal is received first.
•To connect the HDMI cable between the TV and Soundbar, be sure to connect the terminals
marked ARC. Otherwise, the TV sound may not be output.
•Be sure to use the cable with the premium HDMI certification logo. In addition, make sure that
the cable is a certified Type A, high-speed HDMI Ethernet cable. (HIGH SPEED HDMI CABLE
WITH ETHERNET)
Connecting the TV that supports HDMI ARC (Audio Return Channel)
LED
Indicator
“Digital Audio
In”
1. With the Soundbar and TV turned off, connect the HDMI cable as shown in the figure.
2. Turn on the Soundbar and TV.
3. TV sound is output from the Soundbar.
•When the TV sound is not output, press the (Multi Function) button at the top of the Soundbar or
the (Source) button on the remote control to select the “Digital Audio In” mode.
•When the sound is not output, check the HDMI Cable connection again.
•Use the volume buttons on the TV’s remote control to change the volume on the Soundbar.
NOTES

ENG - 20
•When you connect the TV that supports the HDMI ARC (Audio Return Channel) to the Soundbar with
an HDMI cable, you can transmit the digital video and audio data without connecting a separate
optical cable.
•We recommend you use a coreless HDMI cable if possible. If you use a cored HDMI cable, use one
whose diameter is less than 14 mm.
•This function is not available if the HDMI cable does not support ARC.
•When the audio in a broadcast is encoded in Dolby Digital and the “Digital Output Audio Format” on
your TV is set to PCM, we recommend that you change the setting to Dolby Digital. When the
setting on the TV is changed, you will experience better sound quality. (The TV menu may use
different words for Dolby Digital and PCM depending on the TV manufacturer.)