Samsung LT-P1795W User manual

English-1
YOUR NEW TV
1 2 4 5
6
7
8
9
10
11
3
Rear Panel Jacks
Use the rear panel jacks to connect an A/V component that will be connected
continuously, such as a VCR or a DVD player.
POWER INPUT
PC VIDEO INPUT
Connect to the video output port on your PC.
COMPONENT 2
Connect a component video/audio.
COMPONENT 1
Connect a component video/audio.
TV ANTENNA
Connects to an antenna or to a cable
TV system.
AUDIO INPUT
Connect audio signal(L/R) from a
camcorder or VCR.
VIDEO INPUT
Connect a video signal from a
camcorder or VCR.
SUPER VIDEO INPUT
Connect an S-Video signal from a
camcorder or VCR.
PC SOUND INPUT
HEADPHONE JACK
Connect a set of external headphones to
this jack for private listening.
KENSINGTON LOCK
Colors may vary depending on the model you purchase .
victoryia 01-14 3/3/04 10:30 PM Page 3

English-2
INSTALLATION
3
Connect a coaxial
cable between the
ANTENNA OUT
terminal on the VCR
and the antenna
terminal on the TV.
4
Connect a set of
audio cables
between the AUDIO
OUT jacks on the
VCR and the AUDIO
jacks on the TV.
5
Connect a video
cable between the
VIDEO OUT jack on
the VCR and the
VIDEO jack on the
TV.
Follow the instructions in “Viewing a VCR or Camcorder Tape” to view your VCR tape.
# Each external input source device has a different back panel configuration.
A coaxial cable is usually included with a VCR. (If not, check your local electronics store).
If you have a “mono” (non-stereo) VCR, use the Y-connector (not supplied) to hook up
to the left and right audio input jacks of the TV. If your VCR is stereo, you must con-
nect two cables.
Connecting a VCR
These instructions assume that you have already connected your TV to an antenna or a
cable TV system .
Skip step 1 if you have not yet connected to an antenna or a cable system.
1
Unplug the cable or
antenna from the
back of the TV.
2
Connect the cable or
antenna to the
ANTENNA IN terminal
on the back of the
VCR.
victoryia 01-14 6/27/03 2:04 AM Page 11

English-3
INSTALLATION
3
Connect an S-video
cable between the
S-VIDEO OUT jack on
the VCR and the
S-VIDEO INPUT jack
on the TV.
An S-video cable is usually included with an S-VHS VCR.
(If not, check your local electronics store.)
# Each external input source device has a different back panel configuration.
1
To begin, follow
steps 1–3 in the
previous section to
connect the antenna
or cable to your
VCR and your TV.
Connecting an S-VHS VCR
Your Samsung TV can be connected to an S-Video signal from an S-VHS VCR.
(This connection delivers a better picture as compared to a standard VHS VCR.)
2
Connect a set of audio
cables between the
AUDIO OUT jacks on
the VCR and the
AUDIO INPUT jacks
on the TV.
victoryia 01-14 6/27/03 2:04 AM Page 12

English-4
INSTALLATION
Note: For an explanation of Component video, see your DVD player owner's manual.
# Each external input source device has a different back panel configuration.
Connecting a DVD Player
The rear panel jacks on your TV make it easy to connect a DVD player to your TV.
1
Connect a set of audio
cables between the
L, R AUDIO INPUT
jacks on the TV and
the AUDIO OUT jacks
on the DVD player.
2
Connect a video cable
between the
COMPONENT1
(Y, Pb, Pr) jacks on
the TV and the Y, Pb,
Pr jacks on the DVD
player.
victoryia 01-14 6/27/03 2:04 AM Page 13

English-5
INSTALLATION
Connecting a PC
Note: This figure shows the Standard Connector-jack panel. The actual configuration
on your TV may be different, depending on the model.
• PC AUDIO INPUT
Connect these to the audio-output jacks on your PC.
• PC VIDEO INPUT
Connect to the video output port on your PC.
# Each external input source device has a different back panel configuration.
TV rear panel
PC VIDEO INPUT (15-pin D-SUB) PC SOUND INPUT (Optional)
PC rear
victoryia 01-14 6/27/03 2:04 AM Page 14

English-6
How to assemble the TV set and stand base
NOTE : The curved side of the stand base should be placed
at the back of the TV set as shown in the above figure.
Colors may vary depending on the model you purchase .
victoryia 54-59 3/3/04 10:34 PM Page 54

English-7
Installing the Wall Mount Kit (sold separately)
Connect the hinge to the wall mount bracket.
1Secure the bracket to the wall. 2
Remove the base from the TV set.
3Mount the TV on the wall mount bracket.
#The wall mount bracket is sold separately.
4
Use (a) holes to attach the VESA mount.
Use (b) holes to attach the wall mount.
Holder-Wall : 1EA Rubber : 4EA Holder-LCD L/R : 2EA Holder-Ass'y : 1EA
Screw FH 4 x 8 : 10EA
Anchor : 4EA
Screw BH 4 x 25 : 4EA
This installation is to be used when attaching the wall mount to a concrete wall.
When attaching to other building materials, please contact your nearest dealer.
Colors may vary depending on the model you purchase .
victoryia 54-59 3/3/04 10:34 PM Page 55

English-8
Using the Anti-Theft Kensington Lock
Retractable Stand
Note: The maximum tilt angle is 10 degrees in the backward direction.
Please do not tilt the TV outside the specified range. Using excessive force
to tilt the TV may cause permanent damage to the mechanical part of the stand.
Figure 2
Figure 1
Cable
The Kensington lock is a device used to physically fix the system when using it in a public place. The locking
device has to be purchased separately. The appearance and locking method may differ from the illustration
depending on the manufacturer. Please refer to the manual provided with the Kensington lock for proper use.
1
Insert the locking device into the Kensington slot on the LCD TV(Figure 1),
and turn it in the locking direction(Figure 2).
2
Connect the Kensington lock cable.
3
Fix the Kensington lock to a desk or a heavy stationary object.
<Optional>
Colors may vary depending on the model you purchase .
victoryia 54-59 3/3/04 10:34 PM Page 56