Samsung Plasma TV User manual

imagine the possibilities
Thank you for purchasing this Samsung product.
To receive more complete service, please register
your product at
www.samsung.com/register
Model Serial No.
Plasma TV
user manual
BN68-01939A-Eng.indd 1 2009-04-15 오후 2:54:30

English - 2
User Instructions
Screen Image retention
Do not display a still image (such as on a video game or when hooking up a PC to this PDP) on the plasma monitor panel for more
than 2 hours as it can cause screen image retention. This image retention is also known as “screen burn”. To avoid such image
retention, reduce the degree of brightness and contrast of the screen when displaying a still image.
Height
The PDP can normally operate only under 2000m in height. It might abnormally function at a place over 2000m in height so do not
install and operate there.
Heat on the top of the PDP TV
The top side of the product may be hot after long period of use as heat dissipates from the panel through the vent hole in the upper
part of the product. This is normal and does not indicate any defect or operation failure of the product. However, children should be
prevented from touching the upper part of the product.
The product is making a ‘cracking’ noise.
A ‘cracking’ noise may occur when the product contracts or expands due to a change of surrounding environment such as
temperature or humidity. This is normal and not a defect of the unit.
Cell Defects
The PDP uses a panel consisting of 2,360,000(HD-level) to 6,221,000(FHD-level)pixels which require sophisticated technology to
produce. However, there may be few bright or dark pixels on the screen. These pixels will have no impact on the performance of
the product.
Avoid operating the TV at temperatures below 5°C(41°F)
A still image displayed too long may cause permanent damage to the PDP Panel.
Watching the PDP TV in 4:3 format for a long period of time may leave traces of borders displayed on the left,
right and centre of the screen caused by the difference of light emission on the screen. Playing a DVD or a
game console may cause similar effect to the screen. Damages caused by the above effect are not covered by
the Warranty.
Afterimage on the Screen.
Displaying still images from Video games and PC for longer than a certain period of time may produce partial afterimages.
To prevent this effect, reduce the ‘brightness’ and ‘contrast’ when displaying still images.
Warranty
Warranty does not cover any damage caused by image retention.
Burn-in is not covered by the warranty.
Installation
Be sure to contact an authorized service centre, when installing your set in a location with heavy dust, high or low temperatures,
high humidity, chemical substance and where it operates continually such as the airport, the train station etc. Failure to do so may
cause a serious damage to your set.
Without producing harmful VOC (Volatile Organic Compounds),
Samsung’s Eco-friendly “Crystal Design” expresses colour gradation thanks to our dual injection technology.
Contact SAMSUNG WORLDWIDE
If you have any questions or comments relating to Samsung products, please contact the SAMSUNG
customer care centre. (See back cover for more informations.)
© 2009 Samsung Electronics Co., Ltd. All rights reserved.









-
-

BN68-01939A-Eng.indd 2 2009-04-15 오후 2:54:31

N O T
Symbol Press Note One-Touch Button TOOLS
English - 3
Contents
Connecting and Preparing Your TV
Checking Parts .......................................................................... 4
Using the Stand-Base ..............................................................4
Assembling the Cables.............................................................. 4
Viewing the Control Panel ......................................................... 5
Viewing the Connection Panel...................................................7
Remote Control ......................................................................... 9
Installing Batteries in the Remote Control ............................... 10
Using the Remote Control Backlight Buttons .......................... 10
Switching On and Off...............................................................10
Placing Your Television in Standby Mode................................ 10
Viewing the Display ................................................................. 11
Viewing the Menus .................................................................. 11
Using the TOOLS Button......................................................... 11
Plug & Play Feature ................................................................12
Channel Control
Storing Channels ................................................................... 13
Managing Channels ................................................................ 14
Picture Control
Changing the Picture Settings................................................. 16
Viewing the Picture in Picture (PIP).........................................19
Setting up the TV with your PC ............................................... 19
PC Display............................................................................... 20
Sound Control
Changing the Sound Setting ................................................... 21
Selecting the Sound Mode ...................................................... 22
Function Description
Conguring the Setup Menu.................................................... 23
Setting the Time ...................................................................... 24
Source List / Edit Name........................................................... 24
Supported Program ................................................................. 25
Media Play
Connecting a USB Device....................................................... 26
Using the Media Play Function................................................ 27
Using and Sorting Photo List................................................... 28
Viewing a Photo or Slide Show .............................................. 29
Using and Sorting the Music List............................................. 31
Playing a Music ...................................................................... 32
Using and Sorting the Movie List............................................. 33
Playing a Movie File ............................................................... 34
Picture / Music Settings Using Media Play.............................. 36
Using the Setup Menu............................................................. 36
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
Media Play-DLNA
Setting the DLNA Network....................................................... 37
Installing the DLNA Application ............................................... 37
Using the DLNA Application ....................................................39
Using the DLNA Function ........................................................ 42
Content Library
Activating the Content Library ................................................. 43
Using the Content Library........................................................ 44
Network........................................................................... 45
Network Connection ................................................................ 45
Network Setup......................................................................... 48
Internet@TV
Getting Started with Internet@TV ...........................................51
Setting up Internet@TV........................................................... 51
Using the Internet@TV service ...............................................52
Troubleshooting for internet@TV ............................................ 53
Help Website ........................................................................... 53
Home Network Centre
Home Network Centre............................................................. 54
Setting Up the Home Network Centre ..................................... 55
Using the Message Function................................................... 56
Using the Media Function........................................................ 57
About Anynet+
Connecting Anynet+Devices .................................................. 58
Setting Up Anynet+................................................................. 59
Scanning and Switching between Anynet+Devices................ 59
Recording ................................................................................ 60
Listening through a Receiver (Home theater) .........................61
Troubleshooting for Anynet+.................................................. 61
Recommendations for Use
Teletext Feature....................................................................... 62
Wall Mount Kit Specications (VESA) ..................................... 63
Preparing before installing Wall- Mount on the wall ................64
How to attach the Stand-Base................................................. 64
Securing the TV to the Wall.....................................................65
Securing the Installation Space............................................... 65
Troubleshooting....................................................................... 66
Specications .......................................................................... 67
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
BN68-01939A-Eng.indd 3 2009-04-15 오후 2:54:31

English - 4
Assembling the Cables
Enclose the cables in the Holder-Wire Cable so that the cables are not visible through the transparent
stand.
Using the Stand-Base
Two or more people should carry the PDP. Never lay the PDP on the oor
because of possible damage to the screen. Always keep the PDP upright.
The PDP can rotate 20 degrees in right and left directions.
N
N
Checking Parts
Owner’s
Instructions
Remote Control/
AAA Batteries (2ea)
Power Cord Warranty Card/
Safety Guide Manual
(Not available in all locations)
Cloth-Clean Program CD
Holder-Ring (4ea)
(Refer to page 64)
Cover-Bottom / Screws (2ea)
PS58B680/PS63B680 only
Cover-Bottom
PS50B650 only
Screw (4ea)
(PS50B650 only)
Holder-Wire
Cable
Ferrite Core for
Power Cord
Ferrite Core for
Headphone
(Not available in all locations)
Ferrite Core (Power Cord, Headphone)
The ferrite cores are used to shield the cables from interference.
When connecting a cable, open the ferrite core and clip it around the cable near the plug.
N
Connecting and Preparing Your TV
-20° ~ 20°
BN68-01939A-Eng.indd 4 2009-04-15 오후 2:54:32

English - 5
Viewing the Control Panel
The product colour and shape may vary depending on the model. N
Front Panel buttons
Touch each button to
operate.
1
SOURCE
Toggles between all the available input sources
(TV, AV1, AV2, Component1, Component2, PC, HDMI1,
HDMI2/DVI, HDMI3, HDMI4).
In the on-screen menu, use this button as you would use
the ENTER
E
button on the remote control.
2
MENU
Press to see an on-screen menu of your TV’s features.
3 + VOL -
Press to increase or decrease the volume. In the on-screen
menu, use the + VOL - buttons as you would use the
◄ and ► buttons on the remote control.
N
4
<CH >
Press to change channels. In the on-screen menu, use the
<CH >buttons as you would use the ▲ and ▼ buttons on
the remote control.
5
POWER INDICATOR
Lights up when the power is on.
6 (
POWER)
Press to turn the TV on and off.
7
REMOTE CONTROL SENSOR
Aim the remote control towards this spot on the TV.remote control towards this spot on the TV.control towards this spot on the TV.
8
SPEAKERS
PS50B650
Continued...
BN68-01939A-Eng.indd 5 2009-04-15 오후 2:54:32

English - 6
The product colour and shape may vary depending on the model. N
PS58B680/PS63B680
1
SOURCE
Toggles between all the available input sources
(TV, AV1, AV2, Component1, Component2, PC, HDMI1,
HDMI2/DVI, HDMI3, HDMI4, USB, DLNA).
In the on-screen menu, use this button as you would use
the ENTER
E
button on the remote control.
2
MENU
Press to see an on-screen menu of your TV’s features.
3 + VOL -
Press to increase or decrease the volume. In the on-screen
menu, use the + VOL - buttons as you would use the
◄ and ► buttons on the remote control.
N
4
<CH >
Press to change channels. In the on-screen menu, use the
<CH >buttons as you would use the ▲ and ▼ buttons on
the remote control.
5
POWER INDICATOR
Blinks and turns off when the power is on and lights up in
stand-by mode.
6 REMOTE CONTROL SENSOR
Aim the remote control towards this spot on the TV.
7 SPEAKERS
8 ( POWER)
Touch the silver sensor below the (P) mark to turn the TV on
and off.
Front Panel buttons
Touch each button to operate.
BN68-01939A-Eng.indd 6 2009-04-15 오후 2:54:33

English - 7
Whenever you connect an audio or video system to your set, ensure that all elements are switched off.
When connecting an external device, match the colour of the connection terminal to the cable.
N
N
1 LAN
Connect a LAN cable to this port to connect to the Network
(SAMSUNG's Internet@TV Service).
2 POWER IN
Connect the supplied power cord.
3AV IN 1(VIDEO / AUDIO R/L)
Video and audio inputs for external devices, such as a
camcorder or VCR.
4PC IN(PC) / AUDIO
Connect to the video and audio output jack on your PC.
5COMPONENT IN 1, 2
Audio (AUDIO R/L) and video (Y/PB/PR) inputs for
Component.
6HEADPHONES JACK
You can connect a set of headphones if you wish to watch a
television programme without disturbing the other people in
the room.
Prolonged use of headphones at a high volume may
damage your hearing
7SERVICE
Connector for service.
8AUDIO OUT(AUDIO R/L)
Connect RCA audio signals from the TV to an external source,
such as Audio equipment.
N
9HDMI IN 1, 2, 3
No additional Audio connection is needed for an HDMI to
HDMI connection.
Whenusing an HDMI/DVI cable connection, you must use
the HDMI IN 2 jack.
What is HDMI?
“High Denition Multimedia interface” allows the
transmission of high denition digital video data and
multiple channels of digital audio.
The HDMI/DVI terminal supports DVI connection to
an extended device with the appropriate cable (not
supplied). The difference between HDMI and DVI is
that the HDMI device is smaller in size, has the HDCP
(High Bandwidth Digital Copy Protection) coding feature
installed, and supports multi - channel digital audio.
DVI AUDIO IN
DVI audio outputs for external devices.
0 ANT IN
75Ω Coaxial connector for Aerial/Cable Network.
Supported modes for HDMI/DVI and Component
480i 480p 576i 576p 720p 1080i 1080p
HDMI/DVI 50Hz X X X O O O O
HDMI/DVI 60Hz X O X X O O O
Component O O O O O O O
-
-
N
-
-
Viewing the Connection Panel
Continued...
TV Rear Panel
5 863
1
4
Cable Television
Network
or
0
9
or
2
7
BN68-01939A-Eng.indd 7 2009-04-15 오후 2:54:34

English - 8
1 USB 1(HDD), USB 2
Connect a USB mass storage device to view photo les
(JPEG), play audio les (MP3) and movie les.
You can connect to SAMSUNG’s network wirelessly.
2 HDMI IN 4
Connect to the HDMI jack of a device with HDMI output.
3 AV IN 2
Video and audio inputs for external devices, such as a
camcorder or VCR.
The product colour and shape may vary depending on the model. N
TV Side Panel
2
3
1
BN68-01939A-Eng.indd 8 2009-04-15 오후 2:54:35

English - 9
Remote Control
You can use the remote control up to a distance of about 23 feet from the TV.
The performance of the remote control may be affected by bright light. N
1
POWER button
(turns the TV on and off)
2
Selects the TV mode directly.
3
Number buttons for direct channel
access
4
Use to select on-screen menu items
5
Temporary sound switch-off
6 Volume increase
Volume decrease
7
Available source selection
8
Channel control button
9
Use to quickly select frequently used
functions.
0
Control the cursor in the menu
!
This function enables you to view
Internet@TV.
@
Use these buttons in the Media Play,
etc.
$
Use to see information on the current
broadcast
%
Use these buttons in the Anynet+ and
Media Play.
^
Press to backlight the buttons on the
remote. This function is convenient
for using at night or when the room is
dark. (Using the remote control with
the ON/OFF( ) light button set to On
will reduce the battery usage time.)
&
Previous channel
*
Next channel
Previous channel
(
Displays the main on-screen menu
)
Press to switch to your favorite
channels.
a
Returns to the previous menu
b
Exit the on-screen menu
c
This function enables you to view and
play photo, music and movie les from
an external device.
(Refer to pages 28 (Photo), 31(Music),
and 33(Movie))
d
This function enables you to view
Content Library.
e
Sound mode selection
f
Picture size selection
Teletext Functions
2
Exit from the teletext display
(depending on the model)
7
Teletext mode selection (LIST/FLOF)
8
Teletext store
9
Teletext size
@
Fastext topic selection
#
Teletext display/mix both
teletext information and the normal
broadcast
$ Teletext reveal
&
Teletext sub page
*
P :Teletext next page
P :Teletext previous page
(
Teletext index
a
Teletext hold
b
Teletext cancel
BN68-01939A-Eng.indd 9 2009-04-15 오후 2:54:35

English - 10
Installing Batteries in the Remote Control
1. Lift the cover at the back of the remote control upward as shown in the gure.
2. Install two AAA size batteries.
Make sure to match the ‘+’ and ‘–’ ends of the batteries with the diagram inside
the compartment.
Using the remote control with the ON/OFF( ) light button set to On will reduce
the battery usage time.
3. Close the cover.
Remove the batteries and store them in a cool, dry place if you won’t be using the
remote control for a long time.
If the remote control doesn’t work, check the following
1. Is the TV power on?
2. Are the plus and minus ends of the batteries reversed?
3. Are the batteries drained?
4. Is there a power outage or is the power cord unplugged?
5. Is there a special uorescent light or neon sign nearby?
N
Using the Remote Control Backlight Buttons
Use this feature in dark surroundings and when you are unable to see the remote control buttons clearly.
1. Press the ON/OFF( ) light button
When ON, the button backlight is turned on for a moment.
Pressing a remote control button when the remote control is on turns the button backlight on for a moment.
Switching On and Off
The mains lead is attached to the rear of your set.
1. Plug the mains lead into an appropriate socket.
The standby indicator lights up on your set.
2. Press the POWERPbutton on your set.
You also can press the POWERPbutton or the TV button on the remote control to turn the TV on.
The programme that you were watching last is reselected automatically.
3. Press the numeric button (0~9) or channel up / down (</ >) button on the remote control or < CH > button on your set.
When you switch the set on for the very rst time, you will be asked to choose language in which the menus are to be displayed.
4. To switch your set off, press the POWERPbutton again.
Placing Your Television in Standby Mode
Your set can be placed in standby mode in order to reduce the power consumption. The standby mode can be useful when you wish to
interrupt viewing temporarily (during a meal, for example).
1. Press the POWER
P
button on the remote control.
The screen is turned off and a red standby indicator appears on your set.
2. To switch your set back on, simply press the POWER
P
, numeric buttons (0~9), TV button or channel up / down (</ >) button
again.
Do not leave your set in standby mode for long periods of time (when you are away on holiday, for example). It is best to unplug
the set from the mains and aerial.
N
N
N
N
N
N
N
N
N
N
BN68-01939A-Eng.indd 10 2009-04-15 오후 2:54:36

English - 11
Viewing the Display
The display identifies the current channel and the status of certain audio-video settings.
1. Press the INFO button on the remote control. The TV will display the channel, the type of
sound, and the status of certain picture and sound settings.
Press the INFO button once more or wait approximately 10 seconds and it disappears
automatically.
Viewing the Menus
1. With the power on, press the MENU button. The main menu appears on the screen.
The menu’s left side has icons: Picture, Sound, Channel, Setup, Input, Application,
Support.
2. Press the ▲ or ▼ button to select one of the icons. Then press the ENTER
E
button
to access the icon’s sub-menu.
3. Press the EXIT button to exit.
The on-screen menus disappear from the screen after about one minute.
Using the TOOLS Button
You can use the TOOLS button to select your frequently used functions quickly and easily. The Tools menu changes depending on
which external input mode you are viewing.
1. Press the TOOLS button. The Tools menu will appear.
2. Press the ▲ or ▼ button to select a menu, then press the ENTER
E
button.
3. Press the ▲ / ▼ / ◄ / ► / ENTER
E
buttons to display, change, or use the selected
items. For a more detailed description of each function, refer to the corresponding page.
Anynet+(HDMI-CEC), see page 59
Picture Size, see page 17
Picture Mode, see page 16
Sound Mode, see page 21
Sleep Timer, see page 24
SRS TS HD, see page 21
Energy Saving, see page 23
Dual I II, see page 22
Add to Favourite (or Delete from Favourite), see page 14
PIP, see page 19
Auto Adjustment, see page 19
•
•
•
•
•
•
•
•
•
•
•
N
N
1 : 49 Thu 1 Jan
ATV
13-1
Mode : Standard
Cell Light : 4
Contrast : 95
Brightness : 45
Sharpness : 50
Colour : 50
Tint (G/R) : G50/R50
Advanced Settings
Picture
Tools
Anynet+ (HDMI-CEC)
Picture Size : 16:9
Picture Mode : Standard
Sound Mode : Custom
Sleep Timer : Off
SRS TS HD : Off
Energy Saving : Off
Dual I II : Mono
Add to Favourite
U Move E Enter e Exit
BN68-01939A-Eng.indd 11 2009-04-15 오후 2:54:36

English - 12
Plug & Play Feature
When the TV is initially powered on, basic settings proceed automatically and subsequently.
The Screen Saver is activated if there is no remote control key input for longer than 1 minute while Plug & Play is running.
The Screen Saver is activated if there is no operating signal for longer than 15 minutes.
1. Press the POWER button on the remote control. Language menu is displayed.
2. Press the ENTER
E
button. Select the appropriate language by pressing the ▲
or ▼ button. Press the ENTER
E
button. The message Select ‘Home Use’ when
installing this TV in your home. is displayed.
3. Press the ◄ or ► button to select Store Demo or Home Use, then the ENTER
E
button.
We recommend setting the TV to Home Use mode for the best picture in your home environment.
Store Demo mode is only intended for use in retail environments.
If the unit is accidentally set to Store Demo mode and you want to return to Home Use (Standard): Press the Volume button on
the TV. When the volume OSD is displayed, press and hold the MENU button on the TV for 5 seconds.
4. Make sure that the antenna is connected to the TV. Press the ENTER
E
button. Area menu is displayed.
5. Press the ENTER
E
button.Select your country or area by pressing the ▲ or ▼ button, then press the ENTER
E
button. Auto
Store menu is displayed.
To stop the search before it has nished, press the ENTER
E
button with Stop selected.
6. The channel search will start end automatically. After all the available channels are stored, the message Set current date and time
is displayed. Press the ENTER
E
button.
7. Press the ◄ or ► button to select Day, Month, Year, Hour, or Minute. Set these by pressing the ▲ or ▼ button.
You can set the Day,Month,Year,Hour, and Minute directly by pressing the numeric buttons on the remote control.
8. The brief instruction on How to get the best performance from your new HDTV is displayed. Press the ENTER
E
button.
You can change previous or next page by pressing the ◄ or ► button.
This menu is available HD Connection Guide in the Support menu.
9. The message Enjoy your TV. is displayed.
If you want to view the TV immediately, select the Watch TV.
If you want to view the See Product Guide, press the ENTER
E
button.
If you want to reset this feature...
1. Press the MENU button to display the menu. Press the ▲ or ▼ button to select Setup,
then press the ENTER
E
button.
2. Press the ENTER
E
button again to select Plug & Play.
3. Enter your 4 digit PIN number. The default PIN number of a new TV set is ‘0-0-0-0’.
If you want to change PIN number, refer to page 23.
The Plug & Play feature is only available in the TV mode.
N
N
N
N
N
N
N
N
N
N
N
N
N
Setup
Plug & Play 
Language : English
Time
Game Mode : Off
BD Wise : Off
Network Type : Cable
Network Setup
Child Lock : On
Plug & Play
Select the OSD Language.
Language : English ►
E Enter
BN68-01939A-Eng.indd 12 2009-04-15 오후 2:54:36

English - 13
Storing Channels
Area
You can change the desired area.
Auto Store
Scans for all channels with active broadcast stations (and availability depends on your
country) and stores them in the TV's memory.
If you want to stop Auto Store, press the ENTEREbutton.
The Stop Auto Store? message will be displayed.
Select Yes by pressing the ◄ or ► button, then press the ENTEREbutton.
Manual Store
Scans for a channel manually and stores it in the TV’s memory.
Programme (Programme number to be assigned to a channel): Sets the programme number using the ▲, ▼ or number (0~9)
buttons.
: Sets the colour system value using the ▲ or ▼ button.
Sound System → BG / DK / I / M: Sets the sound system value using the ▲ or ▼ button.
Channel (When you know the number of the channel to be stored): Press the ▲ or ▼ button to select C(Air channel) or
S (Cable channel). Press the ► button, then press the ▲, ▼ or number (0~9) buttons to select the required number.
You can also select the channel number directly by pressing the number (0~9) buttons.
If there is abnormal sound or no sound, reselect the sound standard required.
Search (When you do not know the channel numbers): Press the ▲ or ▼ button to start the search. The tuner scans the
frequency range until the rst channel or the channel that you selected is received on the screen.
Store (When you store the channel and associated programme number): Set to OK by pressing the ENTERE button.
Channel mode
C (Air channel mode): You can select a channel by entering the assigned number to each air broadcasting station in this
mode.
S (Cable channel mode): You can select a channel by entering the assigned number for each cable channel in this mode.
Channel Mode
When the press the P / button, channels will be switched within the selected channel list.
Added Ch.: Channels will be switched within the memorized channel list.
Favourite Ch.: Channels will be switched within the favourite channel list.
Fine Tune
If the reception is clear, you do not have to ne tune the channel, as this is done automatically during the search and store
operation. If the signal is weak or distorted, you may have to ne tune the channel manually.
Fine tuned channels that have been saved are marked with an asterisk *.
If you do not store the ne-tuned channel in memory, adjustments are not saved.
To reset the ne-tuning, select Reset by pressing the ▼ button and then press the ENTERE button.
❑
❑
N
❑
•
•
•
•
N
N
•
•
N
-
-
❑
•
•
❑
N
N
N
Channel Control
Channel
Area : Asia/Europe 
Auto Store
Manual Store
Channel List
Channel Mode : Added Ch.
Fine Tune
BN68-01939A-Eng.indd 13 2009-04-15 오후 2:54:37

English - 14
Managing Channels
Channel List
Using this menu, you can Add / Delete or set Favourite channels and use the programme
guide for digital broadcasts.
Select a channel in the All Channels, Added Channels, Favourites, or Programmed
screen by pressing the ▲ / ▼ buttons, and pressing the ENTEREbutton. Then you
can watch the selected channel.
All Channels: Shows all currently available channels.Shows all currently available channels.
Added Channels: Shows all added channels.Shows all added channels.
Favourites: Shows all favourite channels.Shows all favourite channels.
Programmed: Shows all current reserved programmes.Shows all current reserved programmes.
Using the Colour buttons with the Channel List
Green (Zoom): Enlarges or shrinks a channel number.
Yellow (Select): Selects multiple channel lists.
TTOOLS(Tools): Displays the Delete (or Add), Add to Favourite (or Delete from
Favourite), Lock (or Unlock), Timer Viewing, Edit Channel Name, Sort, Select All,
Deselect All,, or Auto Store menu.
(The Options menus may differ depending on the situation.)
Channel Status Display Icons
♥
A channel set as a Favourite. cA channel selected by pressing the yellow button.
\A locked channel. )A reserved programme
Press the CH LIST button on the remote control to bring up the channel lists.
Channel List Tools Menu (in All Channels / Added Channels /
Favourites)
Press the TOOLS button to use the tools menu.
Option menu items may differ depending on the channel status.
Add / Delete
You can delete or add a channel to display the channels you want.
All deleted channels will be shown on All Channels menu.
A gray-coloured channel indicates the channel has been deleted.
The Add menu only appears for deleted channels.
You can also delete a channel to the Added Channels or Favourite menu in the
same manner.
Add to Favourite / Delete from Favourite
You can set channels you watch frequently as favourites.
Press the TOOLS button to display Tools menu.
You can also add the favourite channel by selecting Tools →
Add to Favourite (or Delete from Favourite).
T
The ♥ symbol will be displayed and the channel will be set as a favourite.
All favourite channels will be shown on Favourites menu.
To select the Favourite channels you have set up, press the FAV.CH button on the
remote control.
Lock / Unlock
You can lock a channel so that the channel cannot be selected and viewed. This
function is available only when the Child Lock is set to On. (see page 23)
The PIN number input screen appears. Enter your 4 digit PIN number.
The default PIN number of a new TV set is '0-0-0-0'. You can change the PIN, by selecting Change PIN from the menu.
The \symbol will be displayed and the channel will be locked.
❑
N
•
•
•
•
N
•
•
•
N
O
❑
N
N

N
N
N
N

N
N
O

N
N
N
Continued...
Channel
Auto Store
Manual Store
Channel List
Channel Mode : Added Ch.
Fine Tune
All Channels
8 C--
6 C--
7 C--
9 C--
10 C--
11 C--
12 C--
13 C--
19 C--
T
Tools
SelectZoom
All Channels
8 C--
6 C--
7 C--
9 C--
10 C--
11 C--
12 C--
13 C--
19 C--
T
Tools
SelectZoom
Delete
Add to Favourite
Lock
Timer Viewing
Edit Channel Name
Sort
▼
BN68-01939A-Eng.indd 14 2009-04-15 오후 2:54:37

English - 15
Timer Viewing
If you reserve a programme you want to watch, the channel is automatically switched to the reserved channel in the Channel List;
even when you are watching another channel. To reserve a programme set the current time rst. (See page 15)
Only memorized channels can be reserved.
You can set the Channel, Date, or Start Time directly by pressing the number buttons on the remote control.
Reserving a programme will be shown on Programmed menu.
Edit Channel Name
Channels can labeled so that their call letters appear whenever the channel is selected.
The names of digital broadcasting channels are automatically assigned and cannot be labeled.
Sort
This operation allows you to change the programme numbers of the stored channels. This operation may be necessary after using
the auto store.
Select All / Deselect All
Select All: You can select all the channels in the channel list.
Deselect All: You can deselect all the selected channels in the channel list.
You can perform the Add/Delete, Add to Favourite/Delete from Favourite, or Lock/Unlock function for multiple channels at
the same time. Select the required channels and press the yellow button to set all the selected channels at the same time.
The cmark appears to the left of the selected channels.
You can only select Deselect All when there is a selected channel.
Auto Store
For further details on setting up options, refer to page 13.
If a channel is locked using the Child Lock function, the PIN input window appears.
Channel List Tools Menu (in Programmed)
You can view, modify or delete a reservation.
Press the TOOLS button to use the tools menu.
Change Info: Select to change a viewing reservation.
Cancel Schedules: Select to cancel a viewing reservation.
Information: Select to view a viewing reservation. (You can also change the
reservation information.)
Select All / Deselect All: Select or deselect all reserved programmes.

N
N
N

N


•
•
N
N
N

N
N
❑
N
•
•
•
•
Programmed
T
Tools
SelectZoom
E
Information
1 / 1 / 2009
13:59 5 Quincy, M.E
18:59 2 The Equalizer
20:59 2 McMillan & Wife
21:59 2 M.Spillane’s mike Hammer
Change Info
Cancel Schedules
Information
Select All
BN68-01939A-Eng.indd 15 2009-04-15 오후 2:54:37

English - 16
Changing the Picture Settings
Mode
You can select the type of picture which best corresponds to your viewing requirements.
Dynamic: Selects the picture for high-denition in a bright room.
Standard: Selects the picture for the optimum display in a normal environment.
Eco : Selects the picture for optimum and eye-comfortable display.
Movie: Selects the picture for viewing movies in a dark room.
Press the TOOLS button to display Tools menu.
You can also set the picture mode by selecting Tools → Picture Mode.
T
Cell Light / Contrast / Brightness / Sharpness / Colour / Tint (G/R)
Your television has several setting options that allow you to control the picture quality.
Cell Light: Adjusts the pixel brightness.
Contrast: Adjusts the contrast level of the picture.
Brightness: Adjusts the brightness level of the picture.
Sharpness: Adjusts the edge denition of the picture.
Colour: Adjusts Colour saturation of the picture.
Tint (G/R): Adjusts the Colour tint of the picture.
Select a picture mode to be adjusted rst. The adjusted values are saved for each picture mode.
When you make changes to Cell Light, Contrast, Brightness, Sharpness, Colour or Tint (G/R), the OSD will be adjusted
accordingly.
In Analogue TV, AV modes of the PAL system, you cannot use the Tint Function.
In PC mode, you can only make changes to Cell Light, Contrast, and Brightness.
Settings can be adjusted and stored for each external device you have connected to an input of the TV.
The energy consumed during use can be signicantly reduced if the level of
brightness of the picture is reduced, and then this will reduce the overall running
cost.
Advanced Settings
You can adjust the detailed settings for your screen including the colour and contrast.
Advanced Settings is available in Standard or Movie mode.
In PC mode, you can only make changes to Dynamic Contrast, Gamma and
White Balance from among the Advanced Settings items.
              Off / Dark / Darker / Darkest
You can enhance the picture depth by adjusting the black colour density.
              Off / Low / Medium / High
You can adjust the screen contrast so that the optimal contrast is provided.
Gamma
You can adjust the primary colour (Red, Green, Blue) Intensity.
Colour Space
Colour Space is a colour matrix composed of red, green and blue colours. Select your favourite colour space to experience the
most natural colour.
Auto:Automatically sets the colour range depending on the input video source.
Native:Sets the colour range wider than the that of the input video source.
Custom: Adjusts the colour range to suit your preference.
Customizing the Color Space
Adjusts the Color range to suit your preference. Color is available when Color Space is set to Custom.
Color: Red / Green / Blue / Yellow / Cyan / Magenta
Red / Green / Blue: You can adjust the RGB values for the selected color.
Reset: Resets the color space to the default values
❑
•
•
•
•
❑
•
•
•
•
•
•
N
N
N
N
N
N
❑
N
N




•
•
•
N
-
-
-
-
Picture Control
Continued...
Colour : 50
Tint (G/R) : G50/R50
Advanced Settings 
Picture Options
Picture Reset
Picture
Mode : Standard 
Cell Light : 4
Contrast : 95
Brightness : 45
Sharpness : 50
Colour : 50
Tint (G/R) : G50/R50
Advanced Settings
Picture
BN68-01939A-Eng.indd 16 2009-04-15 오후 2:54:37

English - 17
White Balance
You can adjust the colour temperature for more natural picture colours.
R-Offset / G-Offset / B-Offset / R-Gain / G-Gain / B-Gain: Changing the adjustment value will refresh the adjusted screen.
Reset: The previously adjusted white balance will be reset to the factory defaults.
Flesh Tone
You can adjust the esh tone to be more or less red.
Changing the adjustment value will refresh the adjusted screen.
      Off / On
You can emphasize object boundaries in the picture.

Setting the xvYCC mode to on increases detail and colour space when watching movies from an external device (i.e. DVD player).
xvYCC is available when the picture mode is set to Movie, and the external input is set to HDMI or Component mode.
Picture Options
You can customize the additional picture settings to suit your preference.
In PC mode, you can only make changes to the Colour Tone, Size, and Screen
Burn Protection from among the items in Picture Options.
Colour Tone Cool / Normal / Warm1 / Warm2 / Warm3
You can select the most comfortable colour tone to your eyes.
The adjusted values are stored according to the selected Picture mode.
Warm1, Warm2 or Warm3 is only activated when the picture mode is Movie.
Size
You can select the picture size which best corresponds to your viewing requirements.
16:9: Adjusts the picture size to 16:9 appropriate for DVDs or wide broadcasting.
Wide Zoom: Magnify the size of the picture more than 4:3.
Zoom: Magnies the 16:9 wide picture (in the vertical direction) to t the screen size.
4:3: This is the default setting for a video movie or normal broadcasting.
Screen Fit: Use the function to see the full image without any cutoff when HDMI (720p / 1080i / 1080p)
or Component (1080i / 1080p) signals are input.
The picture size options may vary depending on the input source.
The items available may differ depending on the selected mode.
In PC Mode, only 16:9 and 4:3 mode can be adjusted.
Settings can be adjusted and stored for each external device you have connected to an input of the TV.
Temporary image retention may occur when viewing a static image on the set for more than two hours.
After selecting Wide Zoom mode: Press the ► button to select Position, then press the ENTERE button.
Press the ▲ or ▼ button to move the screen up / down. Then press the ENTERE button.
After selecting Zoom mode: Press the ► button to select Position, then press the ENTERE button. Press the ▲ or ▼
button to move the picture up and down. Then press the ENTERE button. Press the ► button to select Size, then press the
ENTERE button. Press the ▲ or ▼ button to magnify or reduce the picture size in the vertical direction.
Then press the ENTERE button.
After selecting Screen Fit in HDMI (720p / 1080i / 1080p) or Component (1080i / 1080p) mode:
Select Position by pressing the ◄ or ►button. Use the ▲, ▼, ◄ or ► button to move the picture.
Reset: Press the ◄ or ► button to select Reset, then press the ENTERE button. You can initialize the setting.
If you use the Screen Fit function with HDMI 720p input, 1 line will be cut at the top, bottom, left and right as in the overscan
function.
Press the TOOLS button to display Tools menu.
You can also set the picture size by selecting Tools → Picture Size.
T
You can select these options simply by pressing the P.SIZE button on the remote
control.
Digital NR Off / Low / Medium / High / Auto
If the broadcast signal received by your TV is weak, you can activate the Digital Noise Reduction feature to help reduce any static
and ghosting that may appear on the screen.
When the signal is weak, select one of the other options until the best picture is displayed.
This function is not available in PC mode.

•
•

N


N
❑
N

N
N

•
•
•
•
•
N
N
N
N
N
N
N
N
N
N
O

N
N
Continued...
Tint (G/R) : G50/R50
Advanced Settings
Picture Options 
Picture Reset
Picture
BN68-01939A-Eng.indd 17 2009-04-15 오후 2:54:38

English - 18
HDMI Black Level Normal / Low
You can directly select the black level on the screen to adjust the screen depth.
This function is active only when the external input connects to HDMI (RGB signals).

Samsung' new generation PDP panels deliver stunning Full HD motion clarity when viewing fast action sports, movies, and games.
Film Mode
You can optimize the picture mode for watching movies.
Off : Turn the Film Mode function off.
Auto1: Automatically adjusts the picture for the best quality when watching a lm.
Auto2: Automatically optimizes the video text when watching a lm.
Film mode is supported in TV, Video, Component(480i / 1080i) and HDMI(1080i).
Cinema Smooth: Offers the ultimate cinema experience.
This function is available when the external input connects to HDMI (1920x1080p@24Hz).

You can get a clear distinction between Real 100Hz and 50Hz, especially when watching fast moving scenes. Therefore, when
seeing slow moving scenes, you will not be able to distinguish between Real 100Hz and 50Hz. Demo 100Hz works only with 50Hz
signal. Real 100Hz demo mode is provided for shop demonstration with special pictures.

This function is for AV device measurement experts. This function displays the blue signal only by removing the red and green
signals from the video signal so as to provide a blue lter effect that is used to adjust the colour and tint of video equipment such as
DVD players, Home Theaters, etc.
Blue Only Mode is available when the picture mode is set to Movie or Standard.
Screen Burn Protection
Congures the Screen Burn Protection Options to prevent and reduce pixel burn.
When an image remains in one position too long, it may cause a permanent burn on the screen.
Pixel Shift: To reduce the possibility of screen burn, this unit is equipped with screen burn prevention technology.
This technology enables you to set picture movement up/down (Vertical) and side to side (Horizontal).
The Time setting allows you to program the time between movement of the picture in minutes.
Set Pixel Shift to On by pressing the ▲ or ▼ button, then press the ENTERE button.
Select the required option by pressing the ▲ or ▼ button, then press the ENTEREbutton.
Available options: Horizontal, Vertical, Time.
Optimum condition for pixel shift
Item TV/AV/Component/HDMI/PC
Horizontal 0~2 2
Vertical 0~4 4
Time (minute) 1~4 min 2 min
The Pixel Shift value may differ depending on the monitor size (inches) and mode.
This function is not available in the Screen Fit mode.
Scrolling: This function helps remove after images on the screen by moving all the pixels on the PDP according to a pattern
Use this function when there are remaining after images or symbols on the screen especially when you displayed a still image
on the screen for a long time.
Side Grey: When you watch TV with the screen ratio of 4:3, the screen is prevented from any damage by adjusting the white
balance on both extreme left and right sides.
Light: When you set the screen ratio to 4:3, it brightens the left and right sides.
Dark: When you set the screen ratio to 4:3, it darkens the left and right sides.

Resets all picture settings to the default values.
Select a picture mode to be reset. The reset is performed for each picture mode.

N


•
•
•
N
•
N


N

•
N
N
N
N
N
N
•
•
-
-
❑
N
Advanced Settings
Picture Options
Picture Reset 
Picture
BN68-01939A-Eng.indd 18 2009-04-15 오후 2:54:38

English - 19
Setting up the TV with your PC
Preset: Press the SOURCE button to select PC mode.
Auto Adjustment
Auto Adjustment allows the PC screen of set to self-adjust to the incoming PC video
signal. The values of ne, coarse and position are adjusted automatically.
This function does not work in DVI-HDMI mode.
Press the TOOLS button to display Tools menu.
You can also set the adjustment by selecting .
T
Screen
The purpose of picture quality adjustment is to remove or reduce picture noise. If the noise is not removed by Fine-tuning alone,
then adjust the frequency as best as possible (Coarse) and Fine-tune again. After the noise has been reduced, readjust the picture
so that it is aligned on the center of screen.
Coarse
Adjusts the frequency when vertical noise appears on the screen.
Fine
Adjusts the screen to be clearer.
PC Position
Adjust the PC’s screen positioning if it does not t the TV screen. Press the ▲ or ▼ button to adjusting the Vertical-Position.Press the ▲ or ▼ button to adjusting the Vertical-Position.
Press the ◄ or ► button to adjust the Horizontal-Position.
Image Reset
You can replace all image settings with the factory default values.
N
❑
N
❑




Viewing the Picture in Picture (PIP)
You can display a sub picture within the main picture of set programme or video input. In
this way, you can watch the picture of set programme or video input from any connected
equipment while watching the main picture.
You may notice that the picture in the PIP window becomes slightly unnatural when you
use the main screen to view a game or karaoke.
Press the TOOLS button to display Tools menu. You can also congure PIP
related settings by selecting Tools → PIP.
T

You can activate or deactivate the PIP function.
Main picture Sub picture
Component1, Component2
HDMI 1, HDMI2/DVI, HDMI 3, HDMI 4
PC
TV, AV1, AV2
 / / /
You can select a size of the sub-picture.
Source TV/AV1/AV2
You can select a source of the sub-picture.
You can select these options simply by pressing the SOURCE button on the remote control.
 / / /
You can select a position of the sub-picture.
In Double ( , ) mode, Position cannot be selected.
Channel
You can select a channel of the sub-picture only when the Source is set to TV.
N
❑


N

N

Setup
Melody : Medium
Energy Saving : Off
PIP 
Brightness : 45
Sharpness : 50
Auto Adjustment 
Screen
Advanced Settings
Picture Options
Picture Reset
Picture
PIP
PIP ◄ On 
Source : TV
Size :
Position :
Channel : ATV 1
Sound Select : Main
U Move E Enter R Return
BN68-01939A-Eng.indd 19 2009-04-15 오후 2:54:38

English - 20
PC Display
Setting Up Your PC Software (Based on Windows XP)
The Windows display-settings for a typical computer are shown below.
The actual screens on your PC will probably be different, depending upon your
particular version of Windows and your particular video card. However, even if your
actual screens look different, the same basic set-up information will apply in almost
all cases. (If not, contact your computer manufacturer or Samsung Dealer.)
1. First, click on ‘Control Panel’ on the Windows start menu.
2. When the control panel window appears, click on ‘Appearance and Themes’ and a
display dialog-box will appear.
3. When the control panel window appears, click on ‘Display’ and a display dialog-box
will appear.
4. Navigate to the ‘Settings’ tab on the display dialog-box.
The correct size setting (resolution)
Optimum: 1920 X 1080 pixels.
If a vertical-frequency option exists on your display settings dialog box, the correct
value is ‘60’ or ‘60 Hz’. Otherwise, just click ‘OK’ and exit the dialog box.
Display Modes
Both screen position and size will vary depending on the type of PC monitor and its resolution.
The resolutions in the table are recommended.
D-Sub and HDMI/DVI Input
Mode Resolution Horizontal Frequency (kHz) Vertical Frequency (Hz) Pixel Clock Frequency (MHz) Sync Polarity (H/V)
IBM
640 x 350
720 x 400
31.469
31.469
70.086
70.087
25.175
28.322
+ / -
- / +
MAC
640 x 480
832 x 624
1152 x 870
35.000
49.726
68.681
66.667
74.551
75.062
30.240
57.284
100.000
- / -
- / -
- / +
VESA CVT
720 x 576
1152 x 864
1280 x 720
1280 x 720
1280 x 960
35.910
53.783
44.772
56.456
75.231
59.950
59.959
59.855
74.777
74.857
32.750
81.750
74.500
95.750
130.000
- / +
- / +
- / +
- / +
- / +
VESA DMT
640 x 480
640 x 480
640 x 480
800 x 600
800 x 600
800 x 600
1024 x 768
1024 x 768
1024 x 768
1152 x 864
1280 x 800
1280 x 800
1280 x 960
1280 x 1024
1280 x 1024
1360 x 768
1440 x 900
1440 x 900
1680 x 1050
31.469
37.861
37.500
37.879
48.077
46.875
48.363
56.476
60.023
67.500
49.702
62.795
60.000
63.981
79.976
47.712
55.935
70.635
65.290
59.940
72.809
75.000
60.317
72.188
75.000
60.004
70.069
75.029
75.000
59.810
74.934
60.000
60.020
75.025
60.015
59.887
74.984
59.954
25.175
31.500
31.500
40.000
50.000
49.500
65.000
75.000
78.750
108.000
83.500
106.500
108.000
108.000
135.000
85.500
106.500
136.750
146.250
- / -
- / -
- / -
+ / +
+ / +
+ / +
- / -
- / -
+ / +
+ / +
- / +
- / +
+ / +
+ / +
+ / +
+ / +
- / +
- / +
- / +
VESA GTF 1280 x 720
1280 x 1024
52.500
74.620
70.000
70.000
89.040
128.943
- / +
- / -
VESA DMT
/ DTV CEA 1920 x 1080p 67.500 60.000 148.500 + / +
When using an HDMI / DVI cable connection, you must use the HDMI IN 2(DVI) jack.
The interlace mode is not supported.
The set might operate abnormally if a non-standard video format is selected.
❑
❑

N
N
N
BN68-01939A-Eng.indd 20 2009-04-15 오후 2:54:38