Samsung UN60ES8000 Guide

E-MANUAL
Thank you for purchasin9 this Samsuno oroquc_.
To recewe more complete service, please register
your product at
www.samsung.com/register
Vlodel Serial No.

Connecting to the Network
Network Connection
There are three ways to attach your TV
to your LAN using cable:
If you want to illustration_
user°s manual°
connection illustrated in your user °
manual°
- You can attach your TV to your
LAN by connecting the LAN port on
the back of your TV to an external

modem using a LAN cable.
- You can attach your TV to your LAN
by connecting the LAN port on the
back of your TV to an IP Sharer
which is connected to an external
modem. Use LAN cable for the
connection.
Depending on how your network
is configured, you may be able to
attach your TV to your LAN by
connecting the LAN port on the back

of your TV directly to a network
wall outlet using a LAN cable. Note
that the wall outlet is attached to a
modem or router elsewhere in your
house.
If your requires Dynamic
IP address, should use an ADSL
modem or that supports
Dynamic Host Configuration Protocol
/DHCP Modems and
DHCP automatically

IP address, subnet mask,
g ewax and values
needs access the Inte_net
do ente_ them manually°
ho_e networks Dynamic
IR address°
netwo_ks require Static IR
address° If requires
Static IR address,
IR address,
and DNS values manually when

up the connection°
get the address,
gatewax and values, contact
Internet Service Provider (ISP/o
have Windows co purer, you
also get these values through
co_putero
You ADSL modems that
DHCP
requires a IP address° ADSL
modems that DHCP also

Static IP addresses°
Network Connection
If you want to illustration,
use_°s manual°
connection illustrated in your user °
manual°
You can connect your TV to your LAN
through a standard wireless router or
modem.
This TV supports the IEEE 802.11a/b/g
and n communication protocols.

Samsung recommends using IEEE
802.11n. When you play video over a
network connection, the video may not
play smoothly.
a wi ess
connected to _P
sharer youtey oy
If the wi ess IP sharer suppor
youy us@ DHCP or'
static IP address to connect
wireless networ_ko

channel the wi ess IP
sha_e_ that
used° If the
is currently being
channel set fo_ _the
wireless IP sha_e_ being
by anothe_ device nea_bx
this will result in and
co munication failure°
only the following
wireless security ©_otocols:::::
Authentication Mode :WEP,
WPAPSK, WPA2PSK

- Encryption Type :WEP, TKIP, AES
If you High-
throughput (G_eenfield/802oSSn
mode Enc_y ion
set to
wireless
TIIII_IPon your
route_, Sa_sung TVs will
suppo_t a
new
connection in co pliance
Wi-Fi ce_tific ion
s cific iOnSo
If your wireless route_

connect to the netwo_k
/Push Configuration) PIN
Identification Numbe_}o
WPS will automatically configure
SSID and in mode°
If your route_; modem, device
connect
the TVo
Connection Methods:::::
the wi ess netwo_k connection in

- Auto Setup {Using the Auto
Network Search function)
- Manual Setup
- wps(psc}
- Pug Access

Setting up the Wired Network
Net o_k Settings
Menu -_ Net o_k -_ Settings
Set the wired or wireless network
connection to use various Internet
services such as Smart Hub, A Sha_e
Ray and perform software upgrades.
Wired
You can configure your TV's wired
network connection automatically when
connecting your TV to a network that

supports DHCP.
connecting
pop_up appears dir_ectly
set wir_ed networ_ko
up TV_s wired
connection auto aticallX follow these
1. Go to the
(
Settings screen.
Settings)
2. Select Start. The network test screen
appears and verifies the network

connection.
3. When the connection has been
verified, the u connected to the
/nte;-net_ /f you have any p_"obbms
using onine pease contact
Inter-net
message appears.
If the connection
port connection°
If the cannot find
networ_k connection values or_

if you to set the connection
manuallx
°'Manual
go to section_
Setup° °'
Manual Wired
You can configure your TV's wired
network connection manually when
connecting your TV to a network
requires a Static IP address.
that
get the address,
gatewax and
Intern
values, contact
Provider (ISR

up TV°s wired
connection anuallX follow these
1. Go to the
(
Settings screen.
Settings)
2. Select Sta_¢. The network connection
screen appears and the verification
process starts.
3. Select The verification process
stops. Select Settings on network
connection screen. The/P Settings

screen appears.
4. Select the/P Setting, and then set
the/P Setting to Ente;- msnus y.
5. Go to the/P Add_ess entry field,
and then select the/P Add_ess using
remote.
6. Enter the first portion of the/P
(for example, 105) into the
first entry field using your remote.
When done, go to the next field.
7. Enter the next portion of the/P

field.
When done, go to the next
8. Repeat the entry process for each
field in the/P Addt_ess.
If you make istake when
entering number, re-enter the
number to
9. When done, go to the Subnet
fields.
10. Repeat the same entry process for
Subnet and

11.When done, select OK. The network
test screen appears and the
verification process starts. When the
connection has been verified, the
s_e to the/nte_ t /f
have any ©_"ob/ems using online
se_vices_ pease contact /nte_net
Sewice R_ovide;s_message appears.
Net o_k Status
Menu -_ Net o_k -_