Sanden GUS-A45HPA User manual
Sanden Heat Pump – Installation Manual
Page 1 of 32
Heat Pump Unit GUS-A45HPA
Sanden Heat Pump – Installation Manual
Page 2 of 32
Contents
Cover page .......................................................................................................................... 1
Contents .............................................................................................................................. 2
Introduction .......................................................................................................................... 3
How it works ........................................................................................................................ 3
Installation details/layout ...................................................................................................... 4
Installation location .............................................................................................................. 5
Heat Pump Unit installation .................................................................................................. 6
Heat Pump/Water piping installation .................................................................................... 7
Water piping installation ....................................................................................................... 8
Heat Pump Unit Water piping .............................................................................................. 9
Typical System Piping........................................................................................................ 10
Mains Power/Electrical installation/ connections ................................................................ 11
How to connect Mains Power ............................................................................................ 11
How to connect tank unit thermistor cable ......................................................................... 1 3
System operation using continuous power ........................................................................ 1 4
Filling the system - Air Purge ............................................................................................ 1 6
Freeze Protection ............................................................................................................. 1 7
Unit Operation - Time Setting ............................................................................................ 1 8
Blackout time setting ......................................................................................................... 1 9
Maintenance Mode ........................................................................................................... 20
How to switch Maintenance Mode .................................................................................. 21
Error Codes ...................................................................................................................... 22
Error Codes ...................................................................................................................... 23
Water supply quality .......................................................................................................... 24
Dimensions and Technical Data ....................................................................................... 25
Dimensions and Technical Data ........................................................................................ 26
Wiring Diagram ................................................................................................................. 27
Warranty Policy .................................................................................................................. 2 8
Warranty Period ................................................................................................................. 2 9
Post installation inspection checklist .................................................................................. 30
Check sheet ....................................................................................................................... 31
PATENTS
This water heater may be protected by one or more patents or registered designs
in the name of Sanden International USA Ltd
TRADE MARKS
® Registered trademark of Sanden International USA Ltd
.
Note: Every care has been taken to ensure accuracy in preparation of this publication.
No liability can be accepted for any consequences that may arise as a result of its application. Sanden is in a
process of continuous improvement with, therefore specifications may be different to those referenced in this
manual – Please contact Sanden International or it’s distributors for the latest specifications at the time of install.
Sanden Heat Pump – Installation Manual
Page 3 of 32
Introduction
The Sanden Heat Pump Water Heater System has been designed using the latest refrigeration
technology to remove the heat from the air to heat water. The refrigerant we use is CO2 which
does not contribute to global warming, so it allows us to help keep a clean healthy earth for
future generations.
We have also considered energy efficiency. By using CO2 as the refrigerant we have produced
one of the most energy efficient units currently available. It’s even more efficient when
connected to off-peak power1 and the noise level is so low it will operate unobtrusively
throughout the night.
How it works
Figure 1: Heat Pump Water Heater System
Note 1 operating conditions may vary depending on the type of off peak tariff that is available in
your area. The unit must have a minimum of 5 hours continuous power available at all time to
allow the unit to operate without affecting reliability.
Tank unit (hot water storage)
Heat pump unit
Sanden Heat Pump – Installation Manual
Page 2 of 32
Contents
Cover page .......................................................................................................................... 1
Contents .............................................................................................................................. 2
Introduction .......................................................................................................................... 3
How it works ........................................................................................................................ 3
Installation details/layout ...................................................................................................... 4
Installation location .............................................................................................................. 5
Heat Pump Unit installation .................................................................................................. 6
Heat Pump/Water piping installation .................................................................................... 7
Water piping installation ....................................................................................................... 8
Heat Pump Unit Water piping .............................................................................................. 9
Typical System Piping........................................................................................................ 10
Mains Power/Electrical installation/ connections ................................................................ 11
How to connect Mains Power ............................................................................................ 11
How to connect tank unit thermistor cable ......................................................................... 1 3
System operation using continuous power ........................................................................ 1 4
Filling the system - Air Purge ............................................................................................ 1 6
Freeze Protection ............................................................................................................. 1 7
Unit Operation - Time Setting ............................................................................................ 1 8
Blackout time setting ......................................................................................................... 1 9
Maintenance Mode ........................................................................................................... 20
How to switch Maintenance Mode .................................................................................. 21
Error Codes ...................................................................................................................... 22
Error Codes ...................................................................................................................... 23
Water supply quality .......................................................................................................... 24
Dimensions and Technical Data ....................................................................................... 25
Dimensions and Technical Data ........................................................................................ 26
Wiring Diagram ................................................................................................................. 27
Warranty Policy .................................................................................................................. 2 8
Warranty Period ................................................................................................................. 2 9
Post installation inspection checklist .................................................................................. 30
Check sheet ....................................................................................................................... 31
PATENTS
This water heater may be protected by one or more patents or registered designs
in the name of Sanden International USA Ltd
TRADE MARKS
® Registered trademark of Sanden International USA Ltd
.
Note: Every care has been taken to ensure accuracy in preparation of this publication.
No liability can be accepted for any consequences that may arise as a result of its application. Sanden is in a
process of continuous improvement with, therefore specifications may be different to those referenced in this
manual – Please contact Sanden International or it’s distributors for the latest specifications at the time of install.
Sanden Heat Pump – Installation Manual
Page 3 of 32
Introduction
The Sanden Heat Pump Water Heater System has been designed using the latest refrigeration
technology to remove the heat from the air to heat water. The refrigerant we use is CO2 which
does not contribute to global warming, so it allows us to help keep a clean healthy earth for
future generations.
We have also considered energy efficiency. By using CO2 as the refrigerant we have produced
one of the most energy efficient units currently available. It’s even more efficient when
connected to off-peak power1 and the noise level is so low it will operate unobtrusively
throughout the night.
How it works
Figure 1: Heat Pump Water Heater System
Note 1 operating conditions may vary depending on the type of off peak tariff that is available in
your area. The unit must have a minimum of 5 hours continuous power available at all time to
allow the unit to operate without affecting reliability.
Tank unit (hot water storage)
Heat pump unit
Sanden Heat Pump – Installation Manual
Page 4 of 32
Installation details
This Heat Pump Water Heater System must be installed by licensed personnel in accordance
with local building codes:
Installing contractor should be licensed by applicable state/province and municipal
authorities to install an Electrical & Plumbing product.
The unit has been designed for heating potable domestic hot water and any other
usage, such as space heating requires a heat exchanger suitable for local codes to be
installed on the system to separate potable and non potable water.
The unit is designed to operate when connected to the water supply with a maximum
operating pressure of 95 PSI (650 kPa). To ensure the mains pressure does not exceed
this, first check incoming cold water mains pressure, and then a pressure regulating
device must be connected to the water supply line.
This system delivers hot water exceeding 120 oF (50 oC).
Installation of a temperature tempering device is MANDATORY to avoid potential
scalds and burns.
The unit must be stored and transported in an upright position. Failure to do so may
render the unit faulty. Such failure is not covered under any warranty agreements.
Failure to comply with the above conditions will void the warranty.
Figure 2: Typical installation layout
Water
Faucet
Pressure Reducer
95 Psi MAX
100 Psi
Sanden Heat Pump – Installation Manual
Page 5 of 32
Installation location
For the most efficient operation of the heat pump unit the optimum location is the
warmest side of the property and there should be sufficient space for the air to circulate
through the unit.
The tank unit should be located as close as possible to the most frequently used hot
water outlet such as a bathroom. It may be located either outside or inside. The heat
pump unit must be located outside and as close as practicable to the tank unit but not
further than 26ft (8m) away from the tank.
Ensure sufficient clearance around the heat pump unit to allow air to circulate and
provide adequate space for service maintenance of the unit (Figure 3).
Although the heat pump unit is very quiet, it is preferable to avoid installing it directly
below a bedroom window.
Install the heat pump unit in an area which allows sufficient ventilation. Poor ventilation
may cause the unit to short cycle and this could increase power consumption by more
than 10%.
Do not install the heat pump unit in a confined space.
If the heat pump unit is installed facing a wall, exhaust air may stain the wall.
Figure 3: Restrictions on where the heat pump unit can be installed (overhead view)
>4” or 100mm clearance
>4” or 100mm clearance
>4” or 100mm clearance
>8” or 200mm clearance
>12” or
300mm
clearance
>4” or 100mm
clearance
• Unit should have a minimum of 36” or 1000mm space above the unit to ensure correct operation
• Discharge Air blowing against a wall/obstacle in front of the unit may stain the wall/obstacle
• If the unit is not able to operate with adequate airflow due to obstacles and reduced clearances, then
heating output will be reduced by approx. 10% and power consumption increased by approx.10%
• For optimum operation install the unit per the above or in a location with no obstacles
Sanden Heat Pump – Installation Manual
Page 4 of 32
Installation details
This Heat Pump Water Heater System must be installed by licensed personnel in accordance
with local building codes:
Installing contractor should be licensed by applicable state/province and municipal
authorities to install an Electrical & Plumbing product.
The unit has been designed for heating potable domestic hot water and any other
usage, such as space heating requires a heat exchanger suitable for local codes to be
installed on the system to separate potable and non potable water.
The unit is designed to operate when connected to the water supply with a maximum
operating pressure of 95 PSI (650 kPa). To ensure the mains pressure does not exceed
this, first check incoming cold water mains pressure, and then a pressure regulating
device must be connected to the water supply line.
This system delivers hot water exceeding 120 oF (50 oC).
Installation of a temperature tempering device is MANDATORY to avoid potential
scalds and burns.
The unit must be stored and transported in an upright position. Failure to do so may
render the unit faulty. Such failure is not covered under any warranty agreements.
Failure to comply with the above conditions will void the warranty.
Figure 2: Typical installation layout
Water
Faucet
Pressure Reducer
95 Psi MAX
100 Psi
Sanden Heat Pump – Installation Manual
Page 5 of 32
Installation location
For the most efficient operation of the heat pump unit the optimum location is the
warmest side of the property and there should be sufficient space for the air to circulate
through the unit.
The tank unit should be located as close as possible to the most frequently used hot
water outlet such as a bathroom. It may be located either outside or inside. The heat
pump unit must be located outside and as close as practicable to the tank unit but not
further than 26ft (8m) away from the tank.
Ensure sufficient clearance around the heat pump unit to allow air to circulate and
provide adequate space for service maintenance of the unit (Figure 3).
Although the heat pump unit is very quiet, it is preferable to avoid installing it directly
below a bedroom window.
Install the heat pump unit in an area which allows sufficient ventilation. Poor ventilation
may cause the unit to short cycle and this could increase power consumption by more
than 10%.
Do not install the heat pump unit in a confined space.
If the heat pump unit is installed facing a wall, exhaust air may stain the wall.
Figure 3: Restrictions on where the heat pump unit can be installed (overhead view)
>4” or 100mm clearance
>4” or 100mm clearance
>4” or 100mm clearance
>8” or 200mm clearance
>12” or
300mm
clearance
>4” or 100mm
clearance
• Unit should have a minimum of 36” or 1000mm space above the unit to ensure correct operation
• Discharge Air blowing against a wall/obstacle in front of the unit may stain the wall/obstacle
• If the unit is not able to operate with adequate airflow due to obstacles and reduced clearances, then
heating output will be reduced by approx. 10% and power consumption increased by approx.10%
• For optimum operation install the unit per the above or in a location with no obstacles
Sanden Heat Pump – Installation Manual
Page 6 of 32
Figure 4: Restrictions on installation between the tank unit and the heat pump unit
Heat Pump Unit Installation
The surface to which the heat pump unit is installed must be firm, preferably a concrete
pad or block. If the surface is firm there is no need to fix the unit to a base surface,
unless there is a likelihood of high wind or local vibration.
If the heat pump unit and tank unit are to fixed, appropriate fixing devices for the
weight/expected duty should be used.
Note: For California installation this water heater must be braced, anchored,
or strapped to avoid falling or moving during an earthquake.
Note : For Florida installation the Heat Pump unit should be installed in accordance with
all local codes regarding Hurricane winds.
Use appropriately treated lumber or pre-fabricated “pump ups” to raise the Heat Pump
unit 4”-6” from the ground – this will allow defrost condensate to drain.
A pressure and temperature relief (PR) valve MUST be installed during the installation
of the tank unit. This is installed in a defined point near the top of the tank unit. The PR
Valve must have a clear drainage where escaping steam or water can flow freely. PR
Valve setting should be 100 Psig
The installation site must be well drained so that any water accumulating (such as rain
or pipe leakage) will drain away and not enter the heat pump unit and the tank unit.
Supply water pressure must be a minimum of 29 PSI (200 kPa) to ensure Heat Pump
unit operation – If pressure is below 29 PSI install a booster pump to water supply.
Note: The entire system is set up and fully functional when supplied. Once all the water and
electric connections have been made the system will operate automatically provided that
mains power is available.
>24” or 600mm
(Maintenance Space)
Maximum pipe length 26ft(8m)
per line between Tank & Heat Pump
Unit.
Maximum number of bends – 6, use
long radius bends not street “L’s”
Sanden Heat Pump – Installation Manual
Page 7 of 32
Cont
The only adjustment required is to the current time setting on the timer setting panel under the
top housing cover, especially if the blackout time setting is desired. See current time setting,
and blackout time section on page 19.
Figure 5: Heat pump installation example and dimensions
Attach the drain elbow to the drain opening located on the bottom of the heat pump unit.
The drain elbow is included in the installation kit for the heat pump unit.
Attach a drain hose with 5/8 inch (16mm) of inner diameter to the drain elbow to guide the
drained water to an appropriate drain.
Water Piping Installation – Heat Pump Unit & Tank
All piping that connects to the water supply must be installed by a licensed plumber.
The water supplied to the system must comply with the potable water quality standard. Use
of water that does not comply with this standard could result in a malfunction of the system.
Description
PH
TDS
(Total
Dissolved
Solids)
Total
Hardness
Aluminium
Chlorides
Copper
Iron
Manganese
Zinc
Maximum
Levels
6.0
to
9.0
Up to
500 ppm
Up to
200ppm
or 12
grains
hardness
Up to
0.2 ppm
Up to
200 ppm
Up to
1.0
ppm
Up to
0.3
ppm
Up to
0.05 ppm
Up to
5
ppm
The water supply must have a pressure of 29 PSI (200 kPa) or higher.
A drain trap must be installed on the drain pipe if water is to be drained to a drain pan
Unit
Weight
123lbs
Sanden Heat Pump – Installation Manual
Page 8 of 32
Cont
This product cannot be connected to a solar water heater.
The piping must be appropriately insulated, consider Heat tape to protect the water piping
in areas with freezing temperatures.
If the piping needs brazing make sure that all flux and flux splatter is wiped away with a wet
cloth. When brazing ensure connections are protected using a wet cloth
As the hot-water supply pipe will expand and contract, use sleeves when penetrating
through concrete walls or slabs.
With buried piping, an outer cover will need to be used that has had both ends sealed to
avoid any ingress of rain.
Use only heat-resistant and corrosive-resistant material to seal the pipe joints.
Cutting and wrenching the piping material may result in oil and dust adhering to it. After
processing, clean the material with a mild detergent before doing any piping work and
smooth the edges to remove any scratches and burrs. (After flowing water through it verify
whether any debris has accumulated on the filter of the faucet and heat pump unit pipe.)
When using PTFE sealing tape ensure that no tape is sticking out of the threads.
Any heat-resistant PVC piping use is NOT recommended due to high outlet water
temperature for between the heat pump and the tank as well as the tank and the mixing
valve.
Follow the manufacturer’s instruction manual for the type of bond, amount to be applied,
curing time, and other specifications.
If any bond or flux has entered the tank unit and the hot water has a chemical/acrid smell
take the following countermeasures.
a) After heating the water in the tank unit, drain it and clean inside the tank unit. Fill the
tank unit with 26 gallons (100 litres) of water and exchange twice.
b) Clean or change the filter.
c) Fill up the tank unit.
d) Drain water from the relief valve for one to two minutes.
e) Run water from all the hot water supply faucets in the house for about ten minutes to
clean inside the pipes.
Sanden Heat Pump – Installation Manual
Page 9 of 32
Heat Pump Unit Water piping
Connect the heat pump unit COLD supply to the tank unit fitting marked Cold Supply. – ½”
NPT Connection (Certain early units may use ½” BSP connections).
Connect the heat pump unit HOT return to the tank unit fitting marked Hot Return – ½”
NPT Connection (Certain early units may use ½” BSP connections).
Connect the mains water supply to the lower fitting on the tank unit marked Cold Water
Inlet.
Connect the hot water supply pipe to the top of the tank unit marked Hot Water Outlet.
Install the PR valve to the fitting on the tank unit marked PR valve, pipe from PR valve
directly to a Building drain, do not install any shut off valve between PR valve and Building
drain.
Run water through the pipe(s) to remove any debris inside before connecting the pipe(s).
After all the piping connections are completed, run water through the system.
Close the shut off valves (four places) and detach the filter on the cold supply connector of
the heat pump unit to confirm there is no debris blocking the filter. Clean the filter if any
debris is found.
Remove the air from the system according to the instructions below on Page 16.
Make sure all the necessary devices are mounted to the pipes as shown in diagram.
If the heat pump unit piping is kinked or clogged or the air inside was not removed during
the test operation, temperature of the supplied hot water may become inconsistent.
Sanden Heat Pump – Installation Manual
Page 8 of 32
Cont
This product cannot be connected to a solar water heater.
The piping must be appropriately insulated, consider Heat tape to protect the water piping
in areas with freezing temperatures.
If the piping needs brazing make sure that all flux and flux splatter is wiped away with a wet
cloth. When brazing ensure connections are protected using a wet cloth
As the hot-water supply pipe will expand and contract, use sleeves when penetrating
through concrete walls or slabs.
With buried piping, an outer cover will need to be used that has had both ends sealed to
avoid any ingress of rain.
Use only heat-resistant and corrosive-resistant material to seal the pipe joints.
Cutting and wrenching the piping material may result in oil and dust adhering to it. After
processing, clean the material with a mild detergent before doing any piping work and
smooth the edges to remove any scratches and burrs. (After flowing water through it verify
whether any debris has accumulated on the filter of the faucet and heat pump unit pipe.)
When using PTFE sealing tape ensure that no tape is sticking out of the threads.
Any heat-resistant PVC piping use is NOT recommended due to high outlet water
temperature for between the heat pump and the tank as well as the tank and the mixing
valve.
Follow the manufacturer’s instruction manual for the type of bond, amount to be applied,
curing time, and other specifications.
If any bond or flux has entered the tank unit and the hot water has a chemical/acrid smell
take the following countermeasures.
a) After heating the water in the tank unit, drain it and clean inside the tank unit. Fill the
tank unit with 26 gallons (100 litres) of water and exchange twice.
b) Clean or change the filter.
c) Fill up the tank unit.
d) Drain water from the relief valve for one to two minutes.
e) Run water from all the hot water supply faucets in the house for about ten minutes to
clean inside the pipes.
Sanden Heat Pump – Installation Manual
Page 9 of 32
Heat Pump Unit Water piping
Connect the heat pump unit COLD supply to the tank unit fitting marked Cold Supply. – ½”
NPT Connection (Certain early units may use ½” BSP connections).
Connect the heat pump unit HOT return to the tank unit fitting marked Hot Return – ½”
NPT Connection (Certain early units may use ½” BSP connections).
Connect the mains water supply to the lower fitting on the tank unit marked Cold Water
Inlet.
Connect the hot water supply pipe to the top of the tank unit marked Hot Water Outlet.
Install the PR valve to the fitting on the tank unit marked PR valve, pipe from PR valve
directly to a Building drain, do not install any shut off valve between PR valve and Building
drain.
Run water through the pipe(s) to remove any debris inside before connecting the pipe(s).
After all the piping connections are completed, run water through the system.
Close the shut off valves (four places) and detach the filter on the cold supply connector of
the heat pump unit to confirm there is no debris blocking the filter. Clean the filter if any
debris is found.
Remove the air from the system according to the instructions below on Page 16.
Make sure all the necessary devices are mounted to the pipes as shown in diagram.
If the heat pump unit piping is kinked or clogged or the air inside was not removed during
the test operation, temperature of the supplied hot water may become inconsistent.
Sanden Heat Pump – Installation Manual
Page 10 of 32
Typical System piping
Figure 6: Typical System piping
Shut off
valves
Check
valves
Water
Faucet
Pressure
Reducer 95 Psi
MAX
100 Psi
Sanden Heat Pump – Installation Manual
Page 11 of 32
Mains Power/Electrical Installation
All Electrical Wiring should be done in accordance with the latest edition of the National
Electrical Code (NEC) and all local State/Province and Municipality codes.
The power requirement for the system is a dedicated 15 amp circuit fitted with a circuit
breaker. This circuit may be connected to constant power or off-peak power.
A local disconnect should be installed adjacent to the Heat Pump unit in accordance to
NEC and local codes.
Installation of this system must be carried out only by a qualified installation technician
(electrical or plumbing).
Electrical connections
Breaker size and wiring must be sized per NEC rules for the rating plate amperage,
MCA and MOP.
Power Supply is 208/230V-1Ph-60Hz
Verify that the tank unit is full of water and the water shut off valves are open before
turning on the power.
How to connect Main Power
Remove the piping cover, terminal block cover and screw clamp fitting. (Philips head
screwdriver required)
Connect the power wiring to the terminal block per the wiring diagram/manual
Ensure ground wire is connected
Secure the power supply wiring below the terminal block with the screw clamp fitting.
Attach the terminal block cover and piping cover back on the heat pump unit.
Sanden Heat Pump – Installation Manual
Page 12 of 32
Figure 7: Power Wiring Connections
Sanden Heat Pump – Installation Manual
Page 13 of 32
How to connect Tank thermistor cable to Heat Pump unit
The thermistor cable and conduit length are designed to cover the maximum allowable
distance between the tank unit and heat pump unit (16.5 feet). If the units are located
closer, the thermistor cable and conduit may be cut to the desired length (Figure 11).
Attach the conduit connector to the conduit end. Push the conduit into the opening on the
connector until the conduit does not go any further. Pull the conduit several times to
ensure the connector is fixed properly to the conduit.
Unscrew and carefully remove the terminal block cover. Do not use unnecessary force to
remove the cover as this could pull and break the cable coming out of the tank unit.
Attach the connector on the end of the thermistor conduit coming from the heat pump unit
side to the opening on the bottom of the cover on the tank unit.
Confirm the gasket is adhered to the thread of the conduit connector before attaching the
connector to the cover. If the gasket is not present, there is a risk of water getting inside
the cover and this may result in a malfunction of the terminal block.
Connect the thermistor cables to the bottom of the terminal block.
Replace the terminal block cover back onto the tank unit and tighten the screws.
Figure 8: Connecting tank unit thermistor cable
Gasket
Conduit
connector
Conduit
Thermistor
cable
Terminal
block
Tank unit
Sanden Heat Pump – Installation Manual
Page 14 of 32
System operation using continuous power
The system runs its water heating cycle once a day to fill up the storage tank unit with
heated water.
If the blackout time function is selected (setting is covered on Page 19) the unit will not
operate during the blackout times – this function is typically used on installations that
have time of use electricity tariffs.
The water heating cycle operation starts automatically when the residual hot water in
the tank unit is less than 40 gallons (150 litres)
The system will not run if the electrical power supply is cut off (i.e. if it is connected to
off-peak power). However, the system will automatically start operation, once the
electric power is restored
System operation if connected to off-peak electricity
There are no special settings for the off-peak connection. The system will run once
power becomes available and the temperature in the tank drops below the set point of
the tank thermistor.
If connecting the unit to off peak power ensure that the off peak tariff provides a
minimum of 5 hours continuous power, as it can take at least four hours to fill the tank
unit with hot water.
If the ambient temperature is lower than 50oF (10oC) this can be longer.
If the unit is connected to off peak power and hot water consumption has been higher
than normal, hot water might not be available until the next power supply cycle.
Daily frequency and amount of hot water consumption may also affect the duration of
the heating cycle operation.
Select the electrical supply mode that best suits the customer’s hot water
consumption. The type of off-peak connection may need to be changed
if hot water supply is not maintained as required.
Sanden Heat Pump – Installation Manual
Page 15 of 32
The basic system installation is now complete, the unit is now ready for initial filling,
air purge and then start up
Check the Installation against the Installation Check list provided at the end of this
manual
Ensure that the work site is tidy; Sanden International recommends the use of Slim Duct or
Fortress product to cover water piping on the outside of the house
Figure 9: Outline of electrical system connections
208/230V Power
Ground Wire
Sanden Heat Pump – Installation Manual
Page 14 of 32
System operation using continuous power
The system runs its water heating cycle once a day to fill up the storage tank unit with
heated water.
If the blackout time function is selected (setting is covered on Page 19) the unit will not
operate during the blackout times – this function is typically used on installations that
have time of use electricity tariffs.
The water heating cycle operation starts automatically when the residual hot water in
the tank unit is less than 40 gallons (150 litres)
The system will not run if the electrical power supply is cut off (i.e. if it is connected to
off-peak power). However, the system will automatically start operation, once the
electric power is restored
System operation if connected to off-peak electricity
There are no special settings for the off-peak connection. The system will run once
power becomes available and the temperature in the tank drops below the set point of
the tank thermistor.
If connecting the unit to off peak power ensure that the off peak tariff provides a
minimum of 5 hours continuous power, as it can take at least four hours to fill the tank
unit with hot water.
If the ambient temperature is lower than 50oF (10oC) this can be longer.
If the unit is connected to off peak power and hot water consumption has been higher
than normal, hot water might not be available until the next power supply cycle.
Daily frequency and amount of hot water consumption may also affect the duration of
the heating cycle operation.
Select the electrical supply mode that best suits the customer’s hot water
consumption. The type of off-peak connection may need to be changed
if hot water supply is not maintained as required.
Sanden Heat Pump – Installation Manual
Page 15 of 32
The basic system installation is now complete, the unit is now ready for initial filling,
air purge and then start up
Check the Installation against the Installation Check list provided at the end of this
manual
Ensure that the work site is tidy; Sanden International recommends the use of Slim Duct or
Fortress product to cover water piping on the outside of the house
Figure 9: Outline of electrical system connections
208/230V Power
Ground Wire
Sanden Heat Pump – Installation Manual
Page 16 of 32
Filling the System & Purging Air
The following steps must be taken to ensure all air is removed from the system.
Incorrect purging of air may cause the water temperature to vary during operation.
Ensure that all piping to tank unit and heat pump unit are installed and connections are
tight, then open the Cold Water Supply Valve to the system
Push up the lever on the PR valve to open, and fill the tank unit with water.
Confirm that water comes out of the relief valve, and then close the lever.
Open the hot water faucets to remove air from the house piping system.
Close the faucets after no air is seen in the water.
Open the water drain plugs (two places) on the heat pump unit.
Close the plugs after no air is seen in the water.
Supply power to the heat pump unit and leave the hot water faucets open for 3 minutes.
Close the faucet after no air can be seen in the water.
Figure 10: Air removal process
Plumb pipes to Storage Tank Unit and Heat Pump Unit.
Push up the lever on the PR valve to open,
and fill in the tank with water.
Confirm the water come out of the relief valve,
and then close the lever.
Open the faucet to remove air. Close the faucet after no air
bubbles can be seen in the water.
Open the water drain plugs (2 places) on the Heat Pump Unit.
Close the plugs after no air is confirmed in the water supply.
Then connect power to the Heat Pump Unit. Open Faucets.
Water drain plugs
PR valve
Sanden Heat Pump – Installation Manual
Page 17 of 32
Freeze protection
Even if the water pipes have been insulated, the piping can freeze if the surrounding
temperature falls below freezing (32oF). This could cause damage to the equipment and
piping so make sure the appropriate freeze protection measures are taken.
Follow the instructions in the installation manual provided with the freeze protection heat
tape.
After completion of the piping, inspect the plumbing for any water leaks from the joints
before installing freeze protection.
Wrap the freeze protection heater around the pipes, up to the water connectors of the
Heat Pump unit.
Ensure the freeze protection heaters are connected to a 24 hours continuous power
supply.
It is important to fully explain the use and operation of the freeze protection heater to the
customer.
When turning off the power, because the unit will not be in use, ALL water must
be drained from the unit and piping.
Note: Heat tape that uses the outside temperature to energize, may not maintain the
temperature of the pipes correctly. It is important to use a heat tape that directly
senses the pipe’s temperature.
Figure 11: Details on wrapping thermal insulation around the piping connector
Sanden Heat Pump – Installation Manual
Page 18 of 32
Unit Operation
Time setting and Blackout time setting
Current time setting
This product contains a built-in clock. As a part of the water heating cycle logic refers to the
current time, it is necessary to set the clock before starting to use the product. The current time
can be set in the Clock Setting Mode as described below.
*Note
There is no need to adjust the time setting for the daylight saving period. Even if the
installation is conducted during the daylight saving period, the clock setting to the
ordinary time (not daylight saving time) is preferable.
1. Switching to Clock Setting Mode
Press the “Enter” key in the Display Mode to switch to the Clock Setting Mode. Time
Display starts flashing once the mode is switched.
2. Setting the Clock
The time setting can be adjusted by pressing “Up” and “Down” keys. Fast forward and
rewind are available by pressing and holding down a key.
3. Executing Setting the Clock
After the clock is adjusted to the current time, press the Enter key to execute the setting.
The time display stops flashing and comes on once the setting is finished.
*Caution
The display automatically goes back to the Clock Display Mode when no panel
operation occurs for more than 60 seconds in the Clock Setting Mode.
If this occurs, changes made will not be reflected to the setting.
If the clock setting is rewound to a time that is earlier than the time when a heating cycle
is triggered, the system will start the heating cycle.
*Note
When no panel operation is performed for more than 60 seconds the display switches to
the Sleep Mode and turns off.
Sleep Mode is cancelled when Up, Down or Enter key is pressed.
Sanden Heat Pump – Installation Manual
Page 19 of 32
Blackout time setting mode
This mode is used to set the blackout time that stops the heat pump unit operation within the
selected time.
Blackout times can be used if the customer has a time of use tariff.
Change the mode
Press and hold down Up and Down keys together in the clock display mode to go to the
blackout time setting mode.
Once the mode is changed, ‘bo’ and ‘00XX’ (00 = start time, XX = end time) are
displayed. (Initial setting = 00 o’clock for both start and end)
Adjust set blackout start time
Press Up or Down key and ‘00’ (start time) in ‘00XX’ starts flashing and ‘XX’ (end time)
illuminates.
Now the blackout start time can be adjusted.
Setting can be changed only in hour increments, not in minutes.
Set blackout start time
Press the Enter key to set the desired time setting.
After the start time is set, the start time display stops flashing.
The end time display will now start flashing.
Adjust blackout end time
Set to the desired end time by using Up and Down keys.
Setting can be performed only in hour increments, not in minutes.
Set blackout end time
Press enter key to adjust the desired time setting.
After the end time is set, the start time and end time are displayed for two seconds,
then it starts to alternately display ‘bo’ and ‘00XX’ (00 = start time, XX = end time).
Go back to clock display mode
Press Enter key to go back to the clock display mode. It will automatically go back to
the clock display mode when no panel operation is performed for more than 60
seconds.
Blackout time setting mode cannot be set unless the end time setting is executed.
Cancel blackout setting
To cancel the blackout setting, set both start and end times to ‘00’.
Setting to other than ‘00’ (01 ~ 23) will be interpreted as a setting error and the end
time will flash.
Make sure to set both times to ‘00’ when cancelling the blackout time setting.
Sanden Heat Pump – Installation Manual
Page 18 of 32
Unit Operation
Time setting and Blackout time setting
Current time setting
This product contains a built-in clock. As a part of the water heating cycle logic refers to the
current time, it is necessary to set the clock before starting to use the product. The current time
can be set in the Clock Setting Mode as described below.
*Note
There is no need to adjust the time setting for the daylight saving period. Even if the
installation is conducted during the daylight saving period, the clock setting to the
ordinary time (not daylight saving time) is preferable.
1. Switching to Clock Setting Mode
Press the “Enter” key in the Display Mode to switch to the Clock Setting Mode. Time
Display starts flashing once the mode is switched.
2. Setting the Clock
The time setting can be adjusted by pressing “Up” and “Down” keys. Fast forward and
rewind are available by pressing and holding down a key.
3. Executing Setting the Clock
After the clock is adjusted to the current time, press the Enter key to execute the setting.
The time display stops flashing and comes on once the setting is finished.
*Caution
The display automatically goes back to the Clock Display Mode when no panel
operation occurs for more than 60 seconds in the Clock Setting Mode.
If this occurs, changes made will not be reflected to the setting.
If the clock setting is rewound to a time that is earlier than the time when a heating cycle
is triggered, the system will start the heating cycle.
*Note
When no panel operation is performed for more than 60 seconds the display switches to
the Sleep Mode and turns off.
Sleep Mode is cancelled when Up, Down or Enter key is pressed.
Sanden Heat Pump – Installation Manual
Page 19 of 32
Blackout time setting mode
This mode is used to set the blackout time that stops the heat pump unit operation within the
selected time.
Blackout times can be used if the customer has a time of use tariff.
Change the mode
Press and hold down Up and Down keys together in the clock display mode to go to the
blackout time setting mode.
Once the mode is changed, ‘bo’ and ‘00XX’ (00 = start time, XX = end time) are
displayed. (Initial setting = 00 o’clock for both start and end)
Adjust set blackout start time
Press Up or Down key and ‘00’ (start time) in ‘00XX’ starts flashing and ‘XX’ (end time)
illuminates.
Now the blackout start time can be adjusted.
Setting can be changed only in hour increments, not in minutes.
Set blackout start time
Press the Enter key to set the desired time setting.
After the start time is set, the start time display stops flashing.
The end time display will now start flashing.
Adjust blackout end time
Set to the desired end time by using Up and Down keys.
Setting can be performed only in hour increments, not in minutes.
Set blackout end time
Press enter key to adjust the desired time setting.
After the end time is set, the start time and end time are displayed for two seconds,
then it starts to alternately display ‘bo’ and ‘00XX’ (00 = start time, XX = end time).
Go back to clock display mode
Press Enter key to go back to the clock display mode. It will automatically go back to
the clock display mode when no panel operation is performed for more than 60
seconds.
Blackout time setting mode cannot be set unless the end time setting is executed.
Cancel blackout setting
To cancel the blackout setting, set both start and end times to ‘00’.
Setting to other than ‘00’ (01 ~ 23) will be interpreted as a setting error and the end
time will flash.
Make sure to set both times to ‘00’ when cancelling the blackout time setting.
Sanden Heat Pump – Installation Manual
Page 20 of 32
Maintenance Mode
Figure 12 Maintenance mode
Maintenance mode is a function to check the heat pump unit status and to check and perform
other settings. It should generally be assumed that the owner does not operate this function.
The following modes can be found in the maintenance mode.
Blackout time setting mode
Set the blackout time.
Error history display mode
Check the history of any errors that may have occurred.
Parameter display mode
Check the values measured by the thermistor.
Drive setting mode:
Switch the heat pump unit on/off.
Compulsory operation mode:
Compulsorily operate the water heating cycle. (Force on)
Pump remote operation mode:
Run the water circulation pump.
Table of contents
Other Sanden Heat Pump manuals
Popular Heat Pump manuals by other brands
Ingersoll-Rand
Ingersoll-Rand ENL 5 Instructions for installation and operation
Steinbach
Steinbach Waterpower 8500 user manual
Finch
Finch HB 9000 Operation, maintenance and installation manual
Fairland
Fairland IPHC150T Installation & user manual
Zodiac
Zodiac PX 50 Instructions for installation and use
Jandy
Jandy AE-Ti Installation and operation manual
York
York SPLIT-SYSTEM YHJD18 THRU 60 Technical guide
HeatPRO
HeatPRO 120 H/C Installation & operation manual
Gree
Gree GWHD(18)ND3CO installation manual
Dimplex
Dimplex LIK 8ME Installation and operating instructions
Mitsubishi Electric
Mitsubishi Electric PKA-A HA7 Series installation manual
atecpool
atecpool WBR-9.5H-A manual
GE
GE AUH2436ZGDA installation instructions
Lamborghini Caloreclima
Lamborghini Caloreclima RUBINO PLUS Use and maintenance manual
Bard
Bard QH242D installation instructions
Daikin
Daikin Altherma EHBH04CBV User reference guide
Bryant
Bryant 548J*D Series installation instructions
Bard
Bard W18H2-A installation instructions