Sangean ATS-405 User manual

Version 1
ATS-405
中文
GB

GB
1
IMPORTANT SAFETY INSTRUCTIONS
1.
2.
3.
4.
5.
6.
7.
8.
9.
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
Do not install near any heat sources such as
radiators, heat registers, stoves, or other apparatus
(including ampliers) that produce heat.
Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two blades
with one wider than the other. A grounding type plug
has two blades and a third grounding prong. The
wide blade or the third prong are provided for your
safety. If the provided plug does not fit into your
outlet. Consult an electrician for replacement of the
obsolete outlet.

2
10.
11.
12.
13.
14.
Protect the power cord from being walked on
or pinched particularly at plugs, convenience
receptacles, and the point where they exit from the
apparatus.
Only use attachments/accessories specied by the
manufacturer.
Use only with the cart, stand, tripod, bracket, or
table specied by the manufacturer, or sold with the
apparatus. When a cart is used, use caution when
moving the cart/apparatus combination to avoid
injury from tip-over.
Unplug this apparatus during lightning storms or
when unused for long periods of time.
Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or
plug is damaged. liquid has been spilled or objects
have fallen into the apparatus, the apparatus has
been exposed to rain or moisture, does not operate
normally, or has been dropped.

GB
3
15.
16.
17.
18.
19.
20.
To Reduce the Risk of Fire or Electric Shock, Do not
Expose This Appliance To Rain or Moisture.
The Shock Hazard Marking and Associated
Graphical Symbol is provided on the rear of unit.
Apparatus shall not be exposed to dripping or
splashing and no objects lled with liquids, shall be
placed on the apparatus.
Excessive sound pressure on ear-and headphones
could impair the hearing ability. Higher setting that
idle on the equalizer leads to higher signal voltages
on the output for ear and headphones.
The power plug should be close to the radio, and
easy to be approached that during the emergency,
to disconnect the power from the radio, just unplug
the power plug from the AC power slot.
Where the MAINS plug or an appliance coupler is
used as the disconnect device, the disconnected
device shall remain readily operable.

4
21. The batteries shall not be exposed to excessive
heat such as sunshine, re or the like.
IMPORTANT NOTE:
To comply with the FCC RF exposure compliance
requirements, no change to the antenna or the
device is permitted. Any change to the antenna or
the device could result in the device exceeding the
RF exposure requirements and void user’s authority
to operate the device.
CAUTION:
These servicing instructions are for use by qualied
service personnel only. To reduce the risk of the
electric shock, do not perform any servicing other
than that contained in the operating instructions
unless you are qualied to so.

GB
5
Introduction
The Sangean ATS-405 world band digital tuning
receiver provides the following range of features:
Professional digital multi-band world receiver
Full shortwave 14 meter bands
Five tuning methods-direct frequency access, auto
scan, manual tuning, memory recall and rotary tuning
ATS (Auto Tuning System)-auto scan and preset
stations
Shortwave meter band selection
148 station presets
2 alarm timers by buzzer and radio
Real time clock
Adjustable sleep timer
Tone control (Music/Normal/News)
1 kHz ne tuning
Squelch function adjusts the receiving threshold and
eliminate weak transmissions
Easy to read LCD display with backlight
Eco-friendly recharging function with LED indicator
Stereo/mono switch
Lock switch

6
Display backlight illumination
Loudspeaker
LCD display
Preset 1 and Squelch button
Preset 2 and Tuning mute button
Preset 5 and tuning step selection button
Preset 3 and software mute button
Charging indicator
Power and sleep timer button
Band width adjustment and buzzer alarm setting
button
Local/DX selection and radio alarm setting button
Display button
Menu and Fine tune button
Preset 6 and AGC control button
Tuning Up/Down control button
Preset 9 and display illumination time adjustment
Frequency input, time set and enter button
Preset delete button
Preset 8 and 12/24 hour format selection button
Memory button
Preset 7 and RDS CT function button
Memory page
Shortwave meter band selection and ATS (Auto Tune
System) execution button
Controls
15
13
12
14
2
5
11
7
9
10
3
4
1
8
6
16
17
18
19
20
21
22
23
24

GB
7
Preset 4 and MW tuning step selection
Radio button selection
FM stereo/mono selection
Headphone socket
AC IN socket of supplied power adapter
Tone control (News/Normal/Music)
Volume control
25
26
27
28
29
30
31

8
LCD display Icons
J
I
H
G
F
E
D
C
B
ABattery power indicator
RDS clock time
Fine tune status
Sleep timer and snooze
Auto Tuning System (ATS) execution
HWS Buzzer wake up
Radio wake up
Shortwave meter band
Squelch ON
Signal level
Key locked
Soft Mute status
Menu
Frequency unit
DX/Local status
Band width
Memory page selection
Frequency and Time display
Radio band
FM stereo indicator
T
S
R
Q
P
O
N
M
L
K
Charge On/Off selection
Lock switch
Foldable stand
Telescopic antenna
Battery compartment
RESET
Controls
32
33
34
35
36
37

GB
9

10
Power Supply
The ATS-405 operates on 4 x UM-3 (AA Size, LR6)
batteries also powered by external AC power adapter
of 7.5V/0.75A (supplied) or external DC power adapter
of 7.5V/0.75A with center pin positive for China and
Taiwan (supplied).
Press and remove battery cover in the direction
indicated by the arrow on the cover. Insert 4 x UM-3 (AA
size, LR6) batteries with polarity shown on the radio
cabinet. Slide battery cover back into place in direction
of arrow until case snaps into place.
Batteries is to be replaced when battery power level
indicator drops or display ashes empty battery level.
Replace the batteries as soon as possible though the
receiver equips with a super capacitor for memory and
time back up.

GB
11
Battery operation using rechargeable
batteries
1. Remove the battery cover on the back of the unit by
sliding the cover in the direction of the arrow.
2. Slide the CHARGE switch located in the bottom side
of radio to ON position.
3. Insert four Rechargeable UM-3 (AA size, LR6) batteries
into the battery compartment. Take care to ensure all
batteries are inserted with the correct polarity as shown
on the back of the radio. The radio is designed to be
used with Nickel Metal Hydride (NiMH) rechargeable
batteries.
4. Plug the mains adaptor into your radio and then plug
the adaptor into the mains.
5. The battery charging LED will flash red indicating
batteries are charging. Batteries will be fully charged
in around 7 hours depending on battery capacity. The
charge LED shows a steady red when the battery
charging is completed.
● Important:
when using rechargeable batteries the battery
switch must be placed in the ON position.

12
Batteries will only be charged when the radio is
switched off and connected to the AC adaptor.
IF the radio is not to be used for any extended
period of time it is recommended that the batteries
are removed from the radio.
The batteries should not be exposed to excessive
heat such as sunshine, re or the like. After use,
disposable batteries should if possible be taken
to a suitable recycling centre. On no account
should batteries be disposed of by incineration
Note:
Do not use a mix of old and new rechargeable batteries.
Do not use a mix of full and empty rechargeable
batteries.
Do not use batteries that have a different mAh capacity
Do not use damaged or leaking batteries
Note:
Duration for charging your battery fully can be varied
according to the battery capacity. Higher capacity
batteries requires longer charging time.

GB
13
Battery operation using non-rechargeable
batteries
If you use non-rechargeable batteries, before replacing
the batteries make sure the CHARGE switch located
in the bottom side of radio to OFF position and follow
above instructions to install and replace batteries.
Setting clock time
1. When the radio is switched off, press and release
Time set button 18, display will show -:--, Use numbered
button 0-9 to enter clock time then press Time set
button again to complete time setting. Second will
start on the display.
Setting the alarm timer
ATS-405 equips with two alarm timers-alarm by radio
and alarm by buzzer.
The alarm can be set when the radio is power on or off.
If the radio is on, press DISPLAY button to display time
mode for alarm setting.

14
a. alarm by buzzer
Press and release buzzer alarm button, display will ash
the last alarm time set and buzzer alarm icon. Press
the numeric buttons to set the alarm time then press
ENTER button to complete buzzer alarm time setting.
Display will show buzzer alarm icon and back to the real
time status after a few seconds.
To cancel the buzzer alarm setting, press and hold buzzer
alarm button until a beep sounds. Display buzzer alarm icon
will disappear and buzzer alarm setting is then cancelled.
When the alarm is on, press POWER button to turn off
the alarm for 24 hours. The buzzer alarm will last for
one hour if not turned off pressing the POWER button.
You can enable the buzzer alarm again by pressing and
holding buzzer alarm button until a beep sounds, display will
appear buzzer alarm icon indicating buzzer alarm is set.
b. alarm by radio
Tune the radio to the required radio station before setting
the radio alarm. Adjust the volume control to make sure
the volume level is big enough to wake you up.
Press and release radio alarm button then follow the
procedures of setting buzzer alarm to set and cancel
the radio alarm.

GB
15
Snooze
When the alarm is on, press any buttons except
POWER button to be in Snooze function for an interval
of 5 minutes before pressing POWER button to turn it
off. Display will ash Snooze and alarm icons.
Setting the sleep timer
Sleep timer allows the listener to set radio auto-shut off
time from 120 to 15 minutes. Press and hold Power/
sleep timer button, display will ash sleep timer icon and
cycle through 120 to 15 minutes. Release the button
when desired shut off time is reached. Radio will remain
on for selected length of time.
To cancel the sleep timer, simply press Power/sleep
timer button again.
Radio operation
There are three waveband selection by pressing BAND
button
Waveband Frequency
coverage
Aerial type
FM 87.50-108 MHz
76-108 MHz
64-108 MHz
Telescopic
Fully extend the aerial,
angle and
rotate for best reception

16
Note:
FM frequency coverage varies from different market.
MW (AM) 520-1710 kHz
522-1710 kHz
Internal bar antenna
Rotate for best reception
SW 2.3-26.10 MHz Telescopic
Fully extend the aerial for
best
reception
Tune the radio
There are ve tuning methods for this radio.
1. ATS-Auto Tuning System
This system automatically scan and preset the received
stations in the order of signal strength,.i.e. best reception
station will be preset at Preset 1 of PAGE A and so on.
ATS function is only available in the FM and MW bands,
shortwave band is not available for ATS function.
To start ATS, turn on the radio, selected required MW or
FM band by pressing BAND button. Press and hold ATS
button for more than 2 seconds until a beep sounds,
radio will automatically scan and preset the received
stations in the order of signal strength.

GB
17
There are 4 pages of preset memory each FM and MW
band and each page covers 9 preset stations. When the
ATS is completed, a beep will sound and radio will stop
at strongest station within your area, To recall the preset
station, press the PAGE button to allocate Page A to D,
then press the preset numeric button.
2. Direct Tuning using the numerical key pad (0-9)
If you know the radio station frequency, select required
MW, FM or SW band by pressing BAND button then press
FREQ button, display will show--.-and ash selected wave
band, using the numerical key pad 0-9 to enter the station
frequency. Press the ENTER button to select the frequency.
Example, for FM band 103.30 MHz, first select FM
band, then press FREQ then the numerical button 1, 0, 3,
3. Press ENTER button to select the frequency.
3. Manual tuning using Tuning Up and Down button
Turn on the radio, select a waveband by pressing BAND
button. A single press on either the Tuning UP or Down
button will change the frequency Up or down.
4. Scan tuning
Press and hold the Tuning UP or Down button will
automatically scan station frequency and stop when a
station is found.

18
Turn on the radio and select a waveband by pressing
BAND button. Press and hold either the Tuning UP or
Down buttons for more than half a second to commence
scan tuning. The radio will scan the station frequency and
stop automatically each time if finds an active station.
When the waveband end is reached, the radio will beep
and continue tuning from the opposite waveband end.
5. Memory recall stations
You can store up to 108 preset station, 36 preset each
on MW/FM/SW band. To store a station in preset
memory, proceed as below.
a. Turn on by radio by pressing Power button
b. Tune to desired station using one of the previously
described tuning methods.
c. Press the Memory button M, the memory symbol
together with suggested memory page and preset
number will ash for a few seconds.
d. Selected the required preset page A to D by pressing
PAGE button and preferred preset number (1-9).
Display will ash the page and memory you select.
Display will show----, if the selected preset is empty.
Display will show previous stored station if preset has
been used.
Press the ENTER button to complete preset setting.

GB
19
Note:
the original memory preset will be overwritten by the new
station if the selected preset already stored a station.
e. To recall a station in memory, turn on the radio and
select a waveband by pressing BAND button. Press
PAGE button to select stored page then the numeric
button 1-9 corresponding to the preset memory. The
radio will instantly tune to the station and display will
show its frequency and memory location.
f . To delete station in memory
Recall the station you like to delete, press the memory
button M, display will ash memory page and preset
number. Press M. DEL button 0, radio will beep and
display will appear dEL indicating the selected preset
station has been deleted.
g. To exchange station positions in memory
To move a preset station to another preset station.
Press Memo button M, preset position will flash.
Press the new desired station by selecting page and
preset number. A beep will sound indicating memory
position has been swapped.