Sanipex KOY User manual

KOY & ZEPHYR
THERMOSTATIC SHOWER MIXER
www.sanipexgroup.com

IMPORTANT PLEASE READ
All products manufactured and supplied by B AGNODESIGN are fit for purpose as long
as they are Installed, used correctly, cleaned and receive regular maintenance in
accordance with these instructions ...
Remove all packaging and check the product for damage or missing parts before commencing
with the installation.
Any alterations made to this product and its components may infringe product certification,
infrin ge water regulations and invalidate the guarantee. The Installation must comply with all
local/national water supply authority regulations/bylaws and building and plumbing
regulations, therefore we strongly recommend that your product be installed by a reputable
qualified trade's person.
PRODUCT LIFECYCLE
"The product L ive C ycle/e is the collective stages that a product goes through from its conception
and design through to its ultimate disposal."
DISPOSAL GUIDANCE
The best way to ensure your Product has a long life is to follow the Care and Maintenance guides
set by the Manufacture after purchase. This document can be found at
www.bagnodesignlondon.com. The life cycle of the product is not in correlation to the
product Guarantee; the standards the products are manufactured or certified to (e.g. CE &
WRAS) can exceed past the Guarantee duration. After the life cycle of the product is deemed
complete by the end-user please follow the below to dispose of the items correctly ...
Mixers (Shower Valves):
If the mixers are no longer accepted due to mechanical use or aesthetic style, these can be
dis posed of at a registered Local Authority waste recycling center where the individual
components can be sorted.
CLEANING CARE GUIDE

Rinse with water to remove the mild soap solution.
We recommend the product is dried using a soft cloth after
every use.
Never use any abrasive or strong cleaning products containing,
bleaches, acids (hydrochloric, formic, phosphorus, chlorine or
acetic), strong detergents, limescale remover, alcohol or dyes
etc. Never use abrasive cleaning pads, wire wool or microfibre
cloths. Never use cleaning equipment that may have been pre-
used and contaminated with the above substances.
Never apply the cleaning product directly onto the finished
surface.




(

INSTALLATION TYPES
Solid Wall Installation - Place the valve on the wall, level and mark the positions of the 2 fixing points,
drill the wall with the correct sized drill bit, install the wall plugs and screw to fasten the valve to the
wall.
Dry Wall Installation - For framed installations ensure that the timber/noggin is capable of securing and
holding the valve in position, make sure the valve is level and use screw to fasten the valve to the wall.

ONE OUTLET / 2 HANDLE — CONCEALED PART
Install the concealed part at a depth so that the
finished surface is between the Min/Max marking
above.
Apply the surrounding finishes, fit the faceplate onto the valve body, if necessary run a small bead of
silicone around the outer rim of the face plate.
Install the cold water supply from the right and
hot water supply from the left as shown per the
above (if possible pressure test.
Remove the protective cover caps before face plate installation
To fit handles please go to page 8 & 9

TWO OUTLET / 2 HANDLE — CONCEALED PART
Install the concealed part at a depth so that the
finished surface is between the Min/Max marking
above.
Install the cold water supply from the right and
hot water supply from the left as shown per the
above (if possible pressure test.
Apply the surrounding finishes, fit the faceplate onto the valve body, if necessary run a small bead of
silicone around the outer rim of the face plate.
Remove the protective cover caps before face plate installation
To fit handles please go to page 8 & 9

THREE OUTLET / 3 HANDLE — CONCEALED PART
Install the concealed part at a depth so that the
finished surface is between the Min/Max marking
above.
Apply the surrounding finishes, fit the faceplate onto the valve body, if necessary run a small bead of
silicone around the outer rim of the face plate.
Install the cold water supply from the right and
hot water supply from the left as shown per the
above (if possible pressure test.
Remove the protective cover caps before face plate installation
To fit handles please go to page 8 & 9
Top outlet to head shower*
Side outlet to hand shower*
Bottom outlet to bath spout or other*

DIVERTER HANDLE INSTALLATION & OPERATION
The diverter has 3 positions. Turn the spindle of the valve as far anti-clockwise until its stops, now
turn it back once, this will now be in the off position (1). Place the diverter handle on at the 12 o’clock
position. Tighten the grub screw from underneath until secure. Insert the screw cover.
The three-outlet mixer utilizes the one and two outlet methods, please follow the above:
Top valve two outlet
Bottom valve — one outlet
To operate turn the handy to the desired outlet. If three outlet mixer 2 functions/outlets can work
simultaneously.
ONE OUTLET
Turn the spindle of the valve as far anti-clockwise until its stops. Place the diverter handle on at the 12
o’clock position. Tighten the grub screw from underneath until secure. Insert the screw cover.
TWO OUTLET
THREE OUTLET

TEMPERATURE CONTROL HANDLE INSTALLATION & OPERATION — ALL MODELS
The Calibration ring is pre-installed and set at the 12 o’clock position at 38°C DO NOT REMOVE
Place the diverter handle in position. Tighten the grub screw from underneath until secure. Insert the
screw cover.
To test function, turn the handle clockwise, then
anti-clockwise, it should stop at the 12 o’clock
position, press the button to turn.
When turning the handle back clockwise, at the
point the button comes to the 12 o’clock position
a ‘click’ will sound and the button pop back up.

ADJUSTMENT OF HANDLES
Caution:
Do not rotate the spindle during any installation
process. Re-align the original marking lines once
the spindle was moved.
1. Spindle gear
2. O-ring
3. Set screw
4. O-ring
5. Handle
6. Set screw
7. Plug
8. Stop ring
9. Handle
Diverter Handle
Align the original
marking lines.
Thermostat Handle
Adjustment of diverter handle
12 o'clock direction. OK!
If not point to 12 O'clock,
reset the handle.
Diverter handle reset steps:
1. Take off the handle.
2. Loosen the screw #3 & 0-ring #2.
3. Take off the gear #1, and slightly rotate the
gear (in a small angle).
4. Fix on the gear then test to fix on the
handle.
5. If the handle still couldn't fixed on correct
position, repeat above Step-3.
6. Until the handle could be fixed on correctly.
Adjustment of diverter handle
Thermostat handle commissioning steps:
1. Take off the handle.
2. Take off stop ring part# 8 and rotate ii till
cutting line points to 12 o'clock, then fix it
onto the cartridge.
3. Fix on the handle.
12 o'clock direction. OK!
If not point to 12 O'clock,
reset the handle.
Rotate the stop ring till
cutting line points to 12
o'clock.

Remove the handle and first make sure the calibration ring is in the correct 12 o'clock position. if
not, place the calibration ring in the 12 o'clock position and re-test. If the calibration ring is in the 12
o'clock position carefully remove.
Open an outlet place a thermometer under the flowing water and adjust the spindle on the
cartridge, right for colder, left for hotter until 38°C is achieved. Place the calibration ring back in
the 12 o’clock position and re-install the hand ie. Re-test to ensure the valve is working correctly.
COMMISSIONING
To Commission a thermostatic mixer firstly check the following: (requirements on page 2)
1. The supply water temperatures are within the valves operating range.
2. The supply working pressures are within the valves operating range.
3. The supply working pressures are balanced
4. Isolating valves (and strainers preferred are provided.
With the temperature control handle in the 12 o’clock position open a water outlet.
Using a thermometer, measure the mixed water temperature at the outlet. If 38°C is achieved the
temperature valve is working correctly. If the temperature is above 38°C re-calibration may be
required. (Please see CALIBRATION)
Carry out the cold-water supply isolation test by isolating the cold water supply to the valve, wait for
five seconds the valve may stop flowing or if water is still flowing check that the temperature is below
46°C.
CALIBRATION
If the mixed water temperature is above or below 38°C you may need to re-calibrate the cartridge.

MAINTENANCE
INLET FILTERS:
Periodically the filters will need to be cleaned. first remove all handles and than the faceplate. Using a
spanner carefully remove the filter housing (not the screwdriver slot) from the mixer body, flush
under water to remove the small debris or soak overnight. Re-install the filters back into the body and
re-tighten.
DIVERTER VALVE
Remove the handle to expose the valve, taking care to protect the surrounding finishes of the mixer
carefully using a spanner unwind the valve from the mixer body. Maintain, repair or replace and the
carefully re-install.
THERMOSTATIC CARTRIDGE
Remove the handle and then the faceplate. To access the thermostatic cartridge cover shroud also
needs to be removed, this can been done by hand anti-clockwise. With the shroud removed the
securing on the right side can be lossened allowing the cartridge to be released. Maintain, repair or
replace and then carefully re-install.

Note:

Note:

INM-KOY/ZEP-THERMO_MIXER-08-21
www.sanipexgroup.com