Santon Aquaheat AH30V Guide

1
Installation and User Instructions
Aquaheat Unvented Water Heaters
Models: AH30V
Please read and understand these instructions before starting work.
Please leave this leaet with the user following installation
PACK CONTENTS
Heater, tundish, service valve, discharge pipe, grommet, xing screws and plugs,
installation and user instructions.
WARNING
This water heater must only be
installed by qualied persons

2
SECTION PAGE
1.0 INTRODUCTION 2
2.0 TECHNICAL SPECIFICATION 4
3.0 INSTALLATION 5
4.0 COMMISSIONING 12
5.0 USER DEMONSTRATION 13
6.0 MAINTENANCE 14
7.0 FAULT FINDING 16
8.0 SPARE PARTS 17
9.0 ACCESSORIES 18
10.0 GUARANTEE 18
11.0 ENVIRONMENTAL INFORMATION 19
12.0 SPARES STOCKISTS 20
Thank you for purchasing a Santon Aquheat 30 litre unvented water heater. The
Aquaheat water heater is manufactured in the UK to the highest standards and has
been designed to meet all the latest relevant safety specications.
The Aquaheat water heater must be installed (Sections 3.0), commissioned (Section
4.0) and maintained (Sections 6.0) by a competent person only. Please read and
understand these instructions prior to installing your Aquaheat unvented water
heater. Particular attention should be paid to the section headed IMPORTANT
INSTALLATION POINTS. Following installation and commissioning, the
operation of the heater should be explained to the user (Section 5.0) and these
instructions left with them for future reference.
This appliance can be used by children aged from 8 years
and above and persons with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge if
they have been given supervision or instruction concerning
use of the appliance in a safe way and understand the
hazards involved.
Children shall not play with the appliance. Cleaning and
user maintenance shall not be made by children without
supervision.
CONTENTS
1.0 INTRODUCTION

3
1.1 IMPORTANT INSTALLATION POINTS
1.1.1 The Aquaheat unvented water heater is factory tted with a
Temperature/Pressure Relief Valve. The factory tted Temperature/
Pressure Relief Valve must not be removed, blocked or restricted in any
way. FAILURE TO PROVIDE ADEQUATE TEMPERATURE AND
PRESSURE RELIEF WILL INVALIDATE ANY GUARANTEE AND
LEAD TO A DANGEROUS INSTALLATION
1.1.2 Expansion must be accommodated within the system. Use of the Expansion
Vessel and Check Valve provided in the Installation Kit will full this
function.
1.1.3 The installation of this water heater is covered by Building Regulation G3.
In order to full the requirements of this Regulation, the heater should be
installed in accordance with these instructions by a competent installer
(i.e. an installer trained in the installation of unvented water heating
systems). All the control and safety valves provided in the Installation Kit
must be used and plumbed in accordance with Figure 01.
1.1.4 The installation must be carried out in accordance with the relevant
requirements of:
• The appropriate Building Regulations either The Building
Regulations, The Building Regulations (Scotland) or Building
Regulations (Northern Ireland).
• The Water Supply (Water Fittings) Regulations in England, Wales and
Northern Ireland and the Scottish Water Byelaws.
WARNING: IF WATER FLOWS FROM THE PRESSURE RELIEF VALVE OR
TEMPERATURE/PRESSURE RELIEF VALVE, THE ELECTRICITY SUPPLY
MUST BE SWITCHED OFF IMMEDIATELY. CONTACT THE SANTON
SERVICE TEAM (Tel: [phone]) OR AN APPROVED INSTALLER.
1.2 PACK CONTENTS
Before commencing installation check that all the following components have been
supplied in the Installation Kit :
• Expansion Vessel ¾” BSP male, precharge pressure 0.32 MPa
(3.5 bar) c/w wall mounting bracket
• Combined Pressure Reducing Valve/Strainer ½” BSP female,
factory set at 0.35 MPa (3.5 bar)
• Single Check Valve 15mm x 15mm compression
• Pressure (expansion) Relief Valve ½” BSP male inlet, ½” BSP
female discharge factory set at 0.6 MPa (6 bar).
• Tundish ½” BSP male inlet, ¾” BSP female outlet
• Wall mounting bracket set

4
Electrical Rating 1.0kW @240V~/ 0.9kW@230V~ or
3.0kW @ 240V~/ 2.75kW @ 230V~
Capacity 30 litres
Weight (30 Litre) 42.5kg (full)
Operating pressure 0.35 MPa (3.5 bar)
Rated pressure 0.6 MPa (6.0 bar)
Expansion vessel charge pressure 0.35 MPa (3.5 bar)
Expansion relief valve setting 0.6 MPa (6.0 bar)
Minimum supply pressure 0.08 MPa (0.8 bar)
Maximum supply pressure to PRV 1.6 MPa (16.0 bar)
Temperature/Pressure Relief Valve 90°C / 0.7 MPa (7.0 bar)
2.0 TECHNICAL SPECIFICATION
FIGURE 01: DIMENSIONS
506
788
665
616

5
3.1 LOCATION
3.1.1 The Aquaheat must be installed by a competent installer in accordance with
Building Regulation G3.
3.1.2 National Wiring rules may contain restrictions concerning the installation of
these units in bathrooms.
3.1.3 The unit should be vertically wall mounted using the wall bracket and levelling
feet supplied. The water connections must always be on the bottom of the unit.
3.1.4 Enough space should be left below the unit for pipe connections and above the
unit for access to the Temperature/Pressure Relief Valve. Refer to Figure 2 and
the Dimensions Table to determine a suitable position for the heater.
3.1.5 NOTE: Ensure that the wall can support the full weight of the unit
(see TECHNICAL SPECIFICATIONS) and that there are no hidden services
(electricity, gas, or water) below the surface of the wall.
3.1.6 DO NOT install where the unit may freeze.
3.1.7 Using Figure 01 and the Dimensions Table as a guide mark the position of the
wall mounting bracket and lower location point. Drill and plug the wall with
suitable xings, x the wall bracket to the wall.
3.1.8 Fit the heater wall bracket to the rear of the unit using the screws provided,
ensuring the central location bolt is pointing towards the bottom of the unit.
3.1.9 Remove the backing paper from the self adhesive pads of the Levelling Feet
and afx them to the lower back of the unit in the approximate positions shown
in Figure 02.
3.1.10 Hang the unit on the wall mounting bracket ensuring the location bolt locates
in the hole in the wall bracket. Position the moulded spacer block between the
tab on the bottom cover moulding and the wall. Insert a No. 10 x 2 ½” long
screw through the tab and spacer block and tighten into wall plug.
3.0 INSTALLATION

6
3.2 PLUMBING
3.2.1 Refer to the section IMPORTANT INSTALLATION POINTS. Plumb in the
valves in the sequence shown in Figure 03. Ensure the valves are installed in
the correct orientation by reference to the direction of ow arrows marked
on them. The Expansion Vessel should be supported by its own wall bracket
(supplied), do not rely on the pipework alone to support it.
3.2.2 The water connections to the unit are 15mm diameter copper tubes suitable
for compression ttings. Do not use solder joints as this will damage the
heater and may prevent servicing under warranty.
3.2.3 The INLET is marked BLUE, the OUTLET is marked RED. Several
hot outlets via conventional taps can be served, however, individual site
demands should be considered when choosing capacity and the number of
outlets to be served.
3.2.4 It is recommended that a WRAS Listed isolating valve is tted on the cold
water supply to the heater.
3.2.5 A drain cock must be tted below the heater in the inlet pipework. It must
be sited between the heater and the Check Valve (see Figure 03).
3.2.6 Plumbers Paste must not be used as it can impair the operation of the valves.
FIGURE 02: BRACKET & LEVELLING FEET POSITIONS

7
3.3.DISCHARGE
It is a requirement of Building Regulation G3 that any discharge from an unvented
system is conveyed to where it is visible, but will not cause danger to persons in or
about the building.
The Tundish supplied and the discharge pipes should be tted in accordance with
the Requirements and Guidance Notes of Building Regulation G3. These are
essentially as follows:
G3 REQUIREMENT
“...there shall be precautions...to ensure that the hot water discharged from safety
devices is safely conveyed to where it is visible but will not cause danger to
persons in or about the building.”
3.3.1 Discharge pipe MUST terminate in a SAFE, VISIBLE position
3.3.2 Water may drip from the discharge pipe of the pressure relief device and
that this pipe must be left open to the atmosphere.
3.3.3 The pressure relief device is to be operated regularly to remove lime
deposits and to verify that it is not blocked
3.3.4 The discharge pipe connected to the pressure relief device is to be
installed in a continuously downward direction and in a frost free
environment.
Aquaheat
30 litre
Heater
FIGURE 03 SCHEMATIC: INSTALLATION DIAGRAM

8
G3 GUIDANCE SECTION 3.9
The discharge pipe (D2) from the tundish should terminate in a safe place where
there is no risk to persons in the vicinity of the discharge, preferably be of metal
and:
1 Be at least one pipe size larger than the nominal outlet size of the safety device
unless its total equivalent hydraulic resistance exceeds that of a straight pipe
9m long i.e. discharge pipes between 9m and 18m equivalent resistance length
should be at least two sizes larger than the nominal outlet size of the safety
device, between 18 and 27m at least 3 sizes larger, and so on. Bends must be
taken into account in calculating the ow resistance. Refer to Table 01 on page
9 and the worked example.
2 An alternative approach for sizing discharge pipes would be to follow BS
6700:1987 Specication for design installation, testing and maintenance of
services supplying water for domestic use within buildings and their curtilages,
Appendix E, section E2 and table 21.
3 Have a vertical section of pipe at least 300mm long, below the tundish before
any elbows or bends in the pipework.
4 Be installed with a continuous fall.
5 Have discharges visible at both the tundish and the nal point of discharge
but where this is not possible or is practically difcult there should be clear
visibility at one or other of these locations. Examples of acceptable discharge
arrangements are:
i Ideally below a xed grating and above the water seal in a trapped gully.
ii Downward discharges at low level; i.e. up to 100mm above external surfaces
such as car parks, hard standings, grassed areas etc. are acceptable providing
that where children may play or otherwise come into contact with discharges a
wire cage or similar guard is positioned to prevent contact, whilst maintaining
visibility.
iii Discharges at high level; e.g. into a metal hopper and metal down pipe with the
end of the discharge pipe clearly visible (tundish visible or not) or onto a roof
capable of withstanding high temperature discharges of water and 3m from any
plastics guttering system that would collect such discharges (tundish visible).

9
iv Where a single pipe serves a number of discharges, such as in blocks of ats,
the number served should be limited to not more than 6 systems so that any
installation discharging can be traced reasonably easily. The single common
discharge pipe should be at least one pipe size larger than the largest individual
discharge pipe (D2) to be connected. If unvented hot water storage systems
are installed where discharges from safety devices may not be apparent i.e. in
dwellings occupied by blind, inrm or disabled people, consideration should
be given to the installation of an electronically operated device to warn when
discharge takes place.
NOTE:The discharge will consist of scalding water and steam. Asphalt,
roong felt and non-metallic rainwater goods may be damaged by such
discharges.
WORKED EXAMPLE OF DISCHARGE PIPE SIZING:
The example below is for a G½” temperature relief valve with a discharge pipe
(D2) having 4 No. elbows and length of 7m from the tundish to the point of
discharge.
From Table 1 (below):
• Maximum resistance allowed for a straight length of 22mm copper
discharge pipe (D2) from a G½” temperature relief valve is 9.0m.
• Subtract the resistance for 4 No. 22mm elbows at 0.8m each = 3.2m
• Therefore the permitted length equates to: 5.8m
• 5.8m is less than the actual length of 7m therefore calculate the next largest
size.
• Maximum resistance allowed for a straight length of 28mm pipe (D2) from a
G1/2 temperature relief valves equates to 18m.
• Subtract the resistance of 4 No. 28mm elbows at 1.0m each = 4.0m
Therefore the maximum permitted length equates to: 14m
• As the actual length is 7m, a 28mm (D2) copper pipe will be satisfactory.
TABLE 01: SIZING OF COPPER DISCHARGE PIPE (D2) FOR COMMON
T & P RELIEF VALVE SIZES.
VALVE OUTLET
SIZE
MINIMUM SIZE OF
DISCHARGE PIPE D1
MINIMUM SIZE OF
DISCHARGE PIPE D2
FROM TUNDISH
MAXIMUM RESISTANCE
ALLOWED, EXPRESSED
AS A LENTGH OF
STRAIGHT PIPE (I.E. NO
ELBOWS OR BENDS
RESISTANCE CREATED BY
EACH ELBOW OR BEND
G 1/2 15MM 22mm
28mm
35mm
UP TO 9M
UP TO 18M
UP TO 27M
0.8M
1.0M
1.4M
G 3/4 22MM 28mm
35mm
42mm
UP TO 9M
UP TO 18M
UP TO 27M
1.0M
1.4M
1.7M
G 1 28MM 35mm
42mm
54mm
UP TO 9M
UP TO 18M
UP TO 27M
1.4M
1.7M
2.3M

10
3.4: ELECTRICAL REQUIREMENTS
WARNING: This appliance must be earthed. It is suitable for a.c. supply only.
Disconnect the electrical supply before removing the terminal cover. Installation
must be in accordance with the current I.E.E. Wiring Regulations.
3.4.1 The unit is supplied tted with a 1.0m 3 core 1.5mm2 exible
cable. The electricity supply should be fused 13 Amp for a 3kW model
and 5 Amp for a 1kW model and be via a double pole isolating switch
with a contact separation of at least 3mm in both poles. Refer to
the schematic wiring diagram below.
3.4.2 The wires are colour coded as follows:
Green and Yellow EARTH
Brown LIVE (L)
Blue NEUTRAL (N)
Fixed grating
Discharge below
(Building Regulation
G3 section 3.9d gives
alternative points
of discharge)
Trapped
gully
Discharge pipe (D2) from tundish,
with continuous fall. See Building
Regulation G3 section 3.9d i-iv,
Table 4 and worked example
300mm
minimum
500mm maximum
Metal discharge pipe (D1) from
Temperature relief valve to tundish
Tundish
Safety device
(e.g. Temperature
relief valve)
FIGURE 04: DISCHARGE PIPE ARRANGEMENT

11
FIGURE 05: WIRING DIAGRAM

12
4.1 PLUMBING
4.1.1 Do not switch on the electrical supply until the unit has been lled
with water and checked for leaks.
4.1.2 Check that all installation, electrical and discharge pipe requirements have
been met.
4.1.3 Check that all water and electrical connections are tight.
4.1.4 Open a hot water tap, turn on mains water supply to the heater.
4.1.5 Allow unit to ll and leave hot tap running for a short while to purge
any air and ush out the pipework. Close the hot tap and check the
system for leaks.
4.1.6 Manually test the operation of the Temperature/Pressure Relief Valve and,
if tted, the Pressure (expansion) Relief Valve. Ensure water ows freely
from the valve(s) and through the discharge pipes.
4.2 ELECTRICAL
4.2.1 Switch on the electrical supply. The indicator light will illuminate during
heating. When the set temperature is reached the indicator light will go
out.
4.2.2 The set temperature can be adjusted by rotating the knob located in the
terminal cover. It is possible to lock the thermostat knob in either the
mid-range or a “hot” position by following the procedures in 7.9 or 7.10
below.. Always switch off the electrical supply before removing the
terminal cover.
4.2.3 Setting the “mid-range” position:
Rotate the thermostat knob to the mid position. Remove the terminal
cover by using a large at bladed screwdriver to depress the four snap
lugs located in the four rectangular depressions on the bottom cover.
Holding the thermostat knob in position, turn the terminal cover over and
remove the backing disc from the underside of the cover. Turn the backing
disc over and ret to the knob ensuring the notch locates with the boss on
the underside of the cover. Ret the terminal cover, the thermostat will
now be locked in the “mid-range” position.
4.2.4 Setting the “hot” position:
Rotate the thermostat knob to mid way through the hot graduated range
(red graphic). Follow the procedure detailed above, however in this case
the knob should be held in the “hot” position previously set. When the
terminal cover has been retted the thermostat will be locked in the “hot”
position. This position is recommended when using the heater in
conjunction with a thermostatic blending valve.
4.0 COMMISSIONING

13
Following Installation and Commissioning of the water heater, the
operation should be fully explained to the user.
5.1 HOT WATER
5.1.1 Indicate the location of the water heater and identify the outlets to
which it is connected.
5.1.2 Explain that the temperature is set upon installation and conrm the
temperature which the water heater is set at.
5.2 SYSTEM MALFUNCTION
5.2.1 Explain how to isolate electrical and water supplies in case of a fault.
5.2.2 Explain that a qualied plumber and/or electrician should be contacted if
there is a fault.
5.2.3 Explain how to identify/check basic faults.
5.3 SYSTEM MAINTENANCE
Explain the necessity to carry out regular maintenance of the water heater
to ensure its continued safe and efcient operation.
5.4 LITERATURE
Hand over the Installation and User Instructions.
5.4.1 The Aquaheat unvented heater stores water at the temperature set on the
adjustable thermostat. This can be set to give temperatures in the range
of 10 to 75°C. To avoid any risk of freezing when the heater is not in use
for long periods during the winter months, do not switch off the electrical
supply and set the thermostat to its minimum position. N.b. This will not
protect other system pipework.
5.4.2 The thermostat can also be locked in either the mid range or a “hot”
(recommended when using in conjunction with a Thermostatic Blending
Valve) position. To lock the thermostat position the instructions given under
Sections 7.9 or 7.10 should be followed. We recommend that this procedure
is carried out by a qualied electrician.
5.4.3 The indicator light will be illuminated when the unit is heating.
5.4.4 To ensure the heater continues to operate at its optimum performance it
should be periodically maintained in accordance with the instructions given
under the Sections headed MAINTENANCE.
5.4.5 IMPORTANT NOTES TO USER
Do not block or restrict the discharge from any safety valve tted.
Do not tamper with any safety valve tted. If water discharges from any
safety valve tted, switch off the electrical supply to the unit immediately.
Contact the Santon Service Team (Tel: [phone]) or an approved
installer. Do not turn the electrical supply on again until the unit has been
checked and approved by a qualied installer.
5.0 EXPLANATION TO USER

14
Warning: disconnect from all electrical supplies before beginning any work on the
unit. Water contained in the heater may be very hot.
To ensure the continued safe and efcient operation of the unit, it should be
regularly maintained.
Maintenance should be carried out by a competent person and any replacement
parts used should be authorised Santon spare parts.
Little maintenance is required, however in hard water areas the unit will require
periodic descaling to ensure efcient operation. To descale the unit:
6.1 Switch off and disconnect the electrical supply. Turn off the water supply to
the unit.
6.2 Open a hot tap to relieve any system pressure. Empty unit by opening the
drain cock in the inlet pipework.
6.3 Remove the terminal cover by using a large at bladed screwdriver to
depress the 4 snap lugs located in the 4 rectangular depressions on the
bottom cover.
6.4 Disconnect the electrical terminations to the element. Disconnect earth links
to the earthing stud. Withdraw the thermostat and thermal cut-out capillary
tubes from the pocket on the element plate.
6.5 Remove the element plate assembly by unscrewing the ve securing screws,
tapped jacking holes are provided (NOTE: a quantity of water may still be
present in the container, it is recommended that a container be placed under
the unit to collect any spillage). Remove any loose scale from the container.
Carefully clean off any scale from the element and thermostat pocket. DO
NOT clean scale from interior container walls.
6.6 Re-assemble the element plate assembly tting a new sealing gasket. Rewire
the unit with reference to the Wiring Diagrams.
6.7 Re-commission the unit following the INSTALLATION and
COMMISSIONING instructions.
6.0 MAINTENANCE

15
6.8 The Temperature/Pressure Relief Valve and the Pressure (expansion) Relief
Valve should be regularly checked. To check the valves:
6.9 Manually operate the valves by either twisting the cap or lifting the lever.
Ensure water ows freely from the valve(s) and through the discharge pipes
(NOTE: the water discharged may be very hot). Ensure the valve(s) reseat
correctly when released.
6.10 Clean the strainer incorporated in the Pressure Reducing Valve. To inspect
and clean the strainer turn off the mains water supply to the heater and open
a hot tap to relieve the system pressure. Unscrew the black cap from the
Pressure Reducing Valve and remove. The strainer will be removed with
the cap. Wash any particulate matter from the strainer under clean running
water. Replace the cap assembly ensuring the sealing ring is correctly tted.
Do not use any other type of sealant. Close hot tap, open mains stop cock
and check for leaks.
The Expansion Vessel should have a precharge pressure of 0.35 MPa
(3.5 bar). This can reduce over time and eventually require re-charging.
To do this:
6.11 Turn off water supply to the unit; open a hot tap to relieve system pressure.
6.12 Remove dust cap from top of Expansion Vessel.
6.13 Check pre-charge pressure using a tyre pressure gauge. If the pressure is
lower than 0.35 MPa (3.5 bar) it should be recharged using a tyre pump
(Schraeder Valve type). DO NOT OVER CHARGE.
6.14 Re-check pressure and when correct replace dust cap.
6.1.5 Turn on mains water supply and close hot tap.

16
Disconnect the electrical supply before removing the terminal cover. It is
recommended that any service operations on the Aquaheat heater are carried out by
a competent person.
FAULT POSSIBLE CAUSES ACTION
Water not heating 1. Electrical supply fault 1. Check electrical supply
2.Thermal cut-out tripped 2. Check cut-out, if operated
reset and check thermostat
operation. If necessary replace
thermostat/thermal cut-out
(see Wiring Diagram)
3.Thermostat fault Check thermostat operation
Replace if necessary.
Discharge of water from Excessive mains water Fit Pressure Reducing Valve
pressure relief valve pressure Pack U1 and U2
pressure (continuously). (see IMPORTANT
INSTALLATION POINTS)
Discharge of water from 1. Expansion in mains not 1. Fit Pack U2 (see IMPORTANT
pressure relief valve possible INSTALLATION POINTS)
(intermittently). 2. Mains pressure exceeds 2. Fit Packs U1 and |U2
0.41 Mpa (4.1 bar)
3. Pack U1 fitted without 3. Fit Pack U2 when using Pack
Pack U2 U2
4.Pressure Relief Valve Fault 4. Replace Pressure Relief Valve
5. Loss of pressure from 5. Check and, if necessary,
Expansion Vessel re-charge Expansion Vessel
pre-charge pressure
(see section 9.0)
Discharge of water from Thermostat and Replace thermostats and
Temperature/Pressure thermal cut out fault thermal cut outs
relief valve and/or
water/steam from
pressure relief valve
No water flow 1. Inlet valves incorrectly Check all valves are correctly
fitted installed in accordance with
flow direction arrows
2. Mains water supply not 2. Check mains water supply
turned on is on
3. Blockage in main water Check for obstructions. If Pack
supply U1 is fitted check the strainer
is not blocked
"Milky water" Oxygenated water Water from a pressurised
system releases oxygen
bubbles when flowing.The
milkiness will disapear
after a short while.
7.0 FAULT FINDING

17
The following comprehensive list of spare parts is available for your Aquaheat
water heater. Please refer to the Rating Label on the side of your heater before
ordering to ensure the correct spare part is obtained.
DO NOT REPLACE WITH PARTS NOT RECOMMENDED BY SANTON -
THIS WILL INVALIDATE YOUR GUARANTEE AND MAY RENDER THE
INSTALLATION DANGEROUS.
DESCRIPTION CODE NO.
Element plate assembly - 30 litre 3kW.................95 606 926
Element plate assembly - 30 litre 1kW.................95 606 925
Thermostat ............................................................95 612 667
Thermal cut-out ....................................................95 612 666
Indicator light .......................................................95 607 995
Element plate gasket .............................................95 611 708
Pressure (expansion) Relief Valve ........................95 607 986
Temperature/Pressure Relief Valve.......................95 607 994
Check Valve ..........................................................95 607 987
Expansion Vessel...................................................95 607 675
Pressure Reducing Valve.......................................95 607 989
Terminal cover c/w thermostat knob.....................95 614 184
8.0 SPARE PARTS

18
The heater can be used to supply several hot water outlets via conventional taps.
It is not recommended for supplying a shower. Individual site demands should be
considered when choosing capacity and the number of outlets to be served.
A Thermostatic Blending Valve can be used in conjunction with this unit.
Accessory Pack U3 (code no. 95 970 354) is recommended. Follow the installation
instructions supplied with the valve for connection to the system.
This water heater is guaranteed for a period of two years from the date of purchase
with the exception of the element and thermal controls which are guaranteed for a
period of one year provided:
1. The unit has been installed in accordance with these instructions and all
necessary inlet controls and safety valves have been tted correctly.
2. Any valves or controls are of Santon recommended type.
3. The unit has not been tampered with and has been regularly maintained as
detailed in these instructions.
4. The unit has been used only for heating potable water.
5. Within 60 days of installation, the user completes and returns the certicate
supplied along with proof of purchase to register the product.
The unit is not guaranteed against damage by frost and the immersion heater is
not guaranteed against excessive scale build up. This guarantee does not affect the
statutory rights of the consumer.
9.0 ACCESSORIES
10.0 GUARANTEE

19
The Waste Electrical and Electronic Equipment (Producer Responsibility)
Regulation 2004
This product is outside of the scope of the European Waste Electrical & Electronic
Equipment Directive as interpreted within the UK.
In the UK this product can therefore be disposed of through commercial non-WEEE
waste facilities.
Santon does not accept any liability under the WEEE directive.
This product is manufactured from many recyclable materials. At the end of its
useful life it should be disposed of at a Local Authority Recycling Centre to realise
the full environmental benets.
Insulation is by means of CFC-free polyurethane foam.
11.0 ENVIRONMENTAL INFORMATION

20
For the fast and efcient supply of spares, please contact the stockists listed below:
Advanced Water Company Ltd.
Unit D5 Enterprise way, Vale Park,
Evesham, Worcs, WR11 1GS
Tel: [phone]
Fax: [phone]
Electric Water Heating Co.
2 Horsecroft Place, Pinnacles
Harlow, Essex, CM19 5BT
Tel: [phone]
E-Mail: [email protected]
SPD
Units 9 & 10 Hexagon Business Centre
Springeld Road, Hayes, Middlesex, UB40 0TY
Tel: [phone]
Parts Centre
Tel: [phone]
www.partscentre.co.uk
Newey & Eyre
Specialist Products Division
Please contact your local branch
UK Spares Ltd.
Unit 1155 Aztec West
Almonsbury,
Bristol BS32 4TF
Tel: [phone]
William Wilson Ltd.
Unit 3A, 780 South Street
Whiteinch, Glasgow, G14 OSY
Tel: [phone]
Customer Service
Tel: [phone]
Fax: [phone]
E - m a i l s a n t o n s e r v i c e @ h e a t e a m . c o . u k
36006135_issue_02
©2011
12.0 SPARES STOCKISTS
Hurricane Way,
Norwich
Norfolk NR6 6EA
www.santon.co.uk