Sanus systems Sanus visionmount vmaa18 User manual

Sanus Systems 2221 Hwy 36 West, Saint Paul, MN 55113 USA

US Customer Service: 1-800-359-5520 • [email protected] • www.sanus.com

VMAA18

Do not use this product for any purpose not explicitly specied by Sanus Systems.

Improper installation or use may cause personal injury and/or property damage. If

you do not understand these instructions, or if you have doubts about the safety

of the installation, contact Sanus Customer Service. Sanus is not liable for injury or

damage caused by incorrect installation or use.

CAUTION

This product contains small items that could be a choking hazard if swallowed.

Keep these items away from young children!

WARNING

Thank you for choosing the Sanus VMAA18 wall mount. The Sanus VMAA18 wall mount is

designed to support a monitor sized up to 50 in. (127cm) and weighing up to 59 kg (130

lbs).The mount is adjustable; it will tilt +5° to -15°, swivel to ±90°, and roll ±6.°

This product is designed for use in wood stud walls only! The wall must be capable of

supporting up to ve times the weight of the monitor and mount combined. If you

have any doubts about the ability of the wall to support the monitor, contact Sanus

Customer Service, or a qualied contractor.

CAUTION

(6901-100016 <04>)

6901-100016 <04>

Supplied Parts and Hardware

Before starting assembly verify all parts are included and undamaged If any parts are missing or damaged do not return the item

to your dealer; contact Sanus Customer Service Never use damaged parts!

[01] x 1 [02] x 1

[04] x 2

[05] x 4

[10] x 1

3/16 in.

[03] x 2

[09] x 10

[15] x 4

5/16 x 2.5 in.

001426.eps

Lag Bolt for Wall Mounts

[30] x 4

1/4-20 x 2.0 in.

[07] x 4

1/4-20

[08] x 2

5/16-18 x 1 in.

[11] x 4

M4 x 12mm

001435.eps

[31] x 1

7/32 in.

[32] x 1

3/16 in.

[12] x 4

M5 x 12mm

[13] x 4

M6 x 12mm

[14] x 4

M8 x 16mm

[24] x 4

M4 x 30mm

[25] x 4

M5 x 30mm

[26] x 4

M6 x 35mm

[27] x 4

M8 x 40mm

[17] x 4

[18] x 4

[19] x 4

[20] x 4

[23] x 4

M6 / M8

[22] x 4

M4 / M5

[29] x 4

M6 / M8

[28] x 8

M4 / M5

[06] x 4

5/16 in.

[16] x 2

[21] x 4

6901-100016 <04>

1: Attach Brackets to Monitor

For Monitors with a Curved Back or Obstruction

For Monitors with a Flat Back

001427.eps

FPM70-Flat and Curved Back Brackets

001427.eps

FPM70-Flat and Curved Back Brackets

[17], [18],

[19], [20]

[03]

[11], [12],

[13], [14]

[28], [29]

001429.eps

FPM70-Brackets not level

001429.eps

FPM70-Brackets not level

001428.eps

FPM70-Curved Back Hardware

[17], [18],

[19], [20]

[03]

[11], [12],

[13], [14]

[28], [29]

[28]

[22], [23]

OPT

Use washer [28] with M4 or M5

hardware only.

OPT

6901-100016 <04>

2: Install Vise Assemblies

3: Install Arm Assembly to Monitor

001430.eps

FPM70-Vise assemblies installed

001431.eps

FPM70-Detail, vise installation

[30]

[03]

[05]

[07]

Do not overtighten the nut [07]. The vise assembly [05] must

rotate freely around the carriage bolt [30].

NOTE

[31]

001438.eps

FPM70-Arm Attachment Detail

001438.eps

FPM70-Arm Attachment Detail

Do not overtighten the fastener in

the vise assemblies [05]. Tighten

only enough to prevent the tubes

[04] from moving.

NOTE

001438.eps

FPM70-Arm Attachment Detail

001420.eps

Arrows

[03]

[04]

[05]

[04]

[03]

001438.eps

FPM70-Arm Attachment Detail

[04]

[02]

6901-100016 <04>

001439.eps

Attach Plate to Wall

4: Install Wall Plate

[06]

001439.eps

Attach Plate to Wall

001439.eps

Attach Plate to Wall

[01]

Do not overtighten the lag bolts [15]. Tighten only

until the washer [06] is pulled rmly against the wall

plate [01]. Periodic maintenance may be required.

NOTE

[15]

This product must only be used with wood studs

spaced 30 - 40 cm (12 - 16 in.) on center.

NOTE

3/16 in.

6901-100016 <04>

5: Attach Arm to Wall Plate

[32]

Avoid potential injuries or property

damage! Ensure the safety bolts [08]

are secure. Periodic maintenance

may be required.

CAUTION

[08]

HEAVY! You will need

assistance with this step.

[02] [01]

6901-100016 <04>

7: Install Cable Management

Be sure to leave enough slack in the

cables to allow the monitor to move

freely. Use the cable ties [09] and wire

clips [16] to secure the cables to the

brackets [03] and arm [02].

NOTE

001454.eps

FPM70-Cable Management

[09]

[16]

001454.eps

FPM70-Cable Management

[09]

[03]

6: Install Preventer

[21]

[10]

[32]

Install the preventer [10] on the left side if

you want the arm to fold to the left. Install

the preventer on the right side if you want

the arm to fold to the right.

OPT

[16]

6901-100016 <04>

Adjust Level

[31]

8: Adjust Monitor Position

001420.eps

Arrows

001420.eps

Arrows

001449.eps

FPM70-Back of Assembly

[A]

Adjust Left / Right Swivel

001451.eps

FPM70-Left / Right Angle

001420.eps

Arrows

001420.eps

Arrows

001451.eps

FPM70-Left / Right Angle

Avoid potential injuries or property damage! Remove the safety

bracket [B] only to adjust the swivel tension nut [C]. Be sure to replace

the safety bracket after adjusting the swivel tension nut. The hex hole

in the safety bracket must seat over the swivel tension nut.

CAUTION

001451.eps

FPM70-Left / Right Angle

[B]

[C]

001451.eps

FPM70-Left / Right Angle

[B]

6901-100016 <04>

Extend or Retract Arm

001447.eps

FMP70-Lower tab/locking fastener

[E]

001452.eps

FPM70-Extend / Retract Arm

Avoid potential injuries or property damage!

Do not remove the adjustment nut [E];

tighten or loosen only as necessary for easy

arm adjustment.

CAUTION

Adjust Up / Down Pitch

001450.eps

FMP70-Up / Down Pitch

001420.eps

Arrows

001453.eps

FPM70-Full Assembly

[D]

Adjust the pitch tension by tightening or

loosening the tension knobs [D].

NOTE

[31]

001420.eps

Arrows

[E]

6901-100016 <04>

Milestone AV Technologies, Inc.and its affiliated corporations and subsidiaries (collectively,“Milestone”),intend to make this manual accurate and complete.However, Milestone makes no

claim that the information contained herein covers all details, conditions, or variations.Nor does it provide for every possible contingency in connection with the installation or use of this

product.The information contained in this document is subject to change without notice or obligation of any kind. Milestone makes no representation of warranty, expressed or implied,

regarding the information contained herein.Milestone assumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document.

Other manuals for Sanus VisionMount VMAA18

Table of contents

Other Sanus Systems Rack & Stand manuals