Sanus Systems Vision Mount VMBR User manual

Assembly Instructions for Vision Mount VMBR
Thank you for purchasing a Vision Mount product. This product is designed to hold a VCR, DVD player, or cable / satellite
box under a VMBR television wall mount. It will accommodate one component up to 15 lbs. Check carefully to make sure
there are no missing or defective parts. Never use defective parts. Improper installation may cause damage or serious injury.
If you do not understand these directions, or have any doubts about the safety of the installation, please call a qualified
contractor or contact Sanus Systems at 800.359.5520 or visit www.sanus.com. We can quickly assist you with installation
questions and missing or damaged parts. Replacement parts for Sanus products purchased through authorized dealers will
be shipped directly to you.
Required Tools: Ratchet or wrench set
Supplied Parts:
(1) Main Arm - a (2) Extension Arm - b (2) Component Holder - c
(2) 17 mm Wide Foam Pad - d (2) 15 mm Wide Foam Pad - e (2) Square Foam Pad - f
(2) Set Screw - g (2) Knob - h (1) Allen Key - i
(1) Mount Bracket - j (2) 6 mm Diameter Bolt - k (2) 6 mm Diameter Nut - l
(1) 8 mm Diameter Bolt - m (1) Tube Spacer - n (2) Washer - o
(1) Plastic Spacer - p (1) 8 mm Diameter Nut - q
Step 1: Place the 2 Square Foam Pads (f) onto the 2 square surfaces on the bottom of the Main Arm (a) as shown
in Diagram 1 below.
Step 2: Place a 17 mm Wide Foam Pad (d) onto the vertical side of each Component Holder (c). Next place a 15
mm Wide Foam Pad (e) onto the horizontal side of each Component Holder as shown in Diagram 2 below.
Sanus Systems 3785 Lexington Ave. North, Saint Paul, MN 55126 800.359.5520 www.sanus.com
Diagram 1 Diagram 2
a
f
c
e
d

Step 3: Add an Extension Arm (b) to each side of the Main Arm (a). Lock each Extension Arm into place at the
desired width using a Set Screw (g). Tighten the Set Screw with the Allen Key (i) as shown in Diagram 3 below.
Step 4: A Component Holder (c) fi ts into the track on the inside of each Extension Arm (b). Next, a Knob (h)
passes through the slot in the Extension Arm from the outside and threads into the hole in each Component Holder
as shown in Diagram 4 below.
Determine how you will mount the VMTV to your TV Wall Mount: There are two different methods to attach
the VMBR component bracket to the wall mount. It is recommended that you use Method 1 described in steps
5 through 8. You may also use Method 2 described in steps 9 through 11. Method 2 will be easier if you already
have a television on your TV Wall Mount.
Method 1
Step 6: Place the 8 mm Diameter Bolt (m) down through the TV Platter in place of the bolt provided with the TV
Wall Mount as shown in Diagram 6 below.
Step 7: Next place the Plastic Cap Bottom onto the TV Wall Mount assembly.
Step 8: Finally add the hardware to the bottom of the 8 mm Diameter Bolt (m) in the following order: Tube Spacer
(n), Washer (o), Component Bracket Assembly, Plastic Spacer (p), Washer (o), and the 8 mm Nut (q) as shown in
Diagram 6 below. Adjust the width and height to fi t your component and the assembly is complete.
Method 2
Step 9: Place the Mount Bracket (j) over the Arm of the TV Wall Mount as shown in Diagram 7 below.
Step 10: Next place both 6 mm Diameter Bolts (k) down through the Mount Bracket (j) so that the square neck of
the bolts fi t into the square holes in the bracket also shown in Diagram 7.
Step 11: Add the component bracket to the assembly so that the two 6 mm Bolts (k) fi t down through the two
square holes in the Main Arm (a) and tighten a 6 mm Nut (l) onto each 6 mm Bolt as shown in Diagram 7 below.
Sanus Systems 3785 Lexington Ave. North, Saint Paul, MN 55126 800.359.5520 www.sanus.com
Step 5: First fi nd the Plastic Cap Bottom from the TV Wall Mount. There is a
pre-punctured hole in the bottom that you must push out as shown in Diagram 5.
032204
Diagram 3 Diagram 4
a
b
g
c
h
b
a
Threaded Hole
Diagram 5
Hole
Diagram 6 Diagram 7
Plastic Cap
Bottom Component Bracket
Assembly
Arm
n
o
m
po
q
k
j
l
Component Bracket
Assembly