Sanus Systems STEEL FOUNDATIONS SFC User manual

4] The Steel Foundations center
channel stand has included a pair of
adjustable studs (j) and 1/4" rubber stud
covers (k). These are for use if you re-
quire your speaker to angle upwards.
Thread the adjustable stud through the
top plate with the allen wrench to the
desired height. Using a machine nut,
lock the threaded stud into place. Photo
5 - Thread the rubber stud covers over
the top of the adjustable stud to protect
your speaker from being scratched. Three Neoprene Isolation pads
should be placed at the rear of the top plate between the top plate and the
speaker to ensure the speaker does not slide off the back of the stand.
*NOTE: The ends of the spiked feet and
steel speaker studs are very sharp and
may scratch floors or furniture. All sharp
objects can be hazardous to children.
For this reason large rubber feet and
rubber isolation pads are provided as
an option. Sanus Systems will not be
liable for damage or injury.
Page 4 Page 1
STEEL FOUNDATIONS® SFC
INSTRUCTION MANUAL
Every effort has been made to ensure that your stands are perfect. If you
have any questions or feel that there is a problem of any kind, please call
our Customer Assistance number. We can assist with questions or damaged/
Photo 4
Photo 5
Sanus Systems 2221 Highway 36 W St. Paul MN 55113 11.22.04
800.359.5520 www.sanus.com

Page 3 * PLEASE READ THE NOTE ON PAGE 4 OF THIS MANUAL!
ʻTake the time to find the right speaker locations for your
listening room.ʼ
Page 2
1] Attach the plastic feet (e) to the
corners of the base with the small pan
head bolts (f). Photo 2-Group two pillars
with the base. Align the holes in the base
with the holes in the isolation block (a).
Bolt the pillars and the base together
with the isolation block between them
using the large pan head bolts (b) and
lock washers (c). Photo 3-Using the
wire guide is optional.
2] Adhere the two inch self-adhesive damping washers (l) to the flush
side of each top plate. The damping washers will be set in between the
top plate and the pillars. (Optional: You may fill the pillars with sand
or shot at this time.) Align the holes in the top plate with corresponding
holes in the top of each pillar. Bolt the pillars and the top plate together
using the flat head bolts(n). Photo 4-The wire guide (m) is optional.
3] Both spiked feet (g) and rubber feet (d) are provided for your Steel
Foundations®. The spiked feet are preferable in terms of performance.
Thread a machine nut (h) over the
spiked feet and thread the ends of the
spiked feet into the threaded inserts in
the corner feet. Adjust the spiked feet
until the stand is level and then lock
into place by tightening the machine
nut. Use of the spiked feet is optional.*
The rubber feet are provided as an
alternative.
Hardware List
(PHOTO 1)
a) isolation block - 1
b) 1-1/2" pan head bolt - 2
c) lock washer - 2
d) rubber isolation pad - 8
e) plastic foot - 4
f) 5/8" pan head bolt - 4
g) carpet spike - 4
h) machine nut - 8
i) allen key - 1
j) threaded stud - 2
k) rubber stud cover - 2
l) cork damping washer - 2
m) wire guide - 2
n) flat head bolt - 2
a
d
e
g
PHOTO 1
Important: This product uses two
different feet for each base. Before
installing, be sure to check that the
feet are mounted with the (1) foot
on the front left and rear right of
the base, (2) front right and rear
left. The designation (1) & (2) are
on the bottom of each foot. Photo 3
Photo 2
h
k
i
j
b
m
l
f
c
n