Sanuvox Bio Smart Screen User manual
Bio Smart Screen Installation Manual
WARNING
READ AND FOLLOW ALL INSTRUCTIONS CONTAINED IN THIS MANUAL BEFORE USE.
FAILURE TO COMPLY WITH THESE INSTRUCTIONS MAY RESULT IN PERSONAL
INJURIES OR DAMAGED UNIT.
All wiring must be done by a professional and in accordance with national and local electrical codes.
Always wear safety glasses and work gloves for protection.
Bio Smart Screen Installation Manual v1.0 - 30-03-17
SANUVOX TECHNOLOGIES INC. | 146, rue Barr, St-Laurent, Quebec, Canada H4T 1Y4
1-888-SANUVOX www.sanuvox.com
2
Congratulations on the purchase of the Sanuvox Bio
Smart Screen. is option will greatly enhance your
experience of the UV Bio-Wall Max air purier by
providing you with added functions. ose functions
include distant monitoring of lamp/ballast status and
lamp age as well as the ability to reset the lamp timer for
each lamp individually tracking them with more
precision.
Engineered and assembled in Montreal (Quebec),
Canada, Sanuvox products are carefully craed to deliver
to you the best that UV Air Purication can oer and
improve your air quality.
About the Bio Smart Screen ............................................. 3
Important Safety Instructions & Warranty..................... 4
Included in the Box............................................................ 5
Installation Considerations............................................... 6
Step by Step Installation .................................................... 7
Setting & Using Bio Smart Screen ................................... 8
Replacement Parts.............................................................. 8
To e Owner
ank You
Table of Contents
3
e Bio Smart Screen was specically designed to be used in conjunction with your Sanuvox UV Bio-Wall Max
air purier.
For information or recommendations relative to sizing for your specic application, please call Sanuvox at 1-888-SANUVOX.
About the Bio Smart Screen
GENERAL
Installation and servicing of the Bio Smart Screen should be performed by trained and accredited personnel only.
Untrained personnel can perform basic maintenance functions such as reconnecting the power and data cables to
the Bio Smart Screen. All other operations should be performed by trained service personnel. When working on the
UV Bio-Wall Max air purier, observe precautions in the literature, tags, labels attached to the unit and any other
safety precautions considered as best practices in the HVAC industry.
e Bio Smart Screen is fragile. Being used in commercial and industrial environment, additional care should be
taken in order to not damage the screen.
Use a damp cloth with mild soaps or alcohol cleaners to clean the exterior of the Bio Smart Screen enclosure and the
touchscreen. Always spot test the cleaner to make sure it does not damage the surface.
Under no circumstances should water be sprayed or splashed onto the Bio Smart Screen.
SAFETY CONSIDERATIONS
HANDLING CONSIDERATIONS
CLEANING CONSIDERATIONS
4
NOTICE
UV lamp can be disposed / recycled aer use as any other uorescent lamp. Contact and follow your local and
federal authorities’ specic instructions.
WARNING
Before installing or performing maintenance on the unit, TURN OFF and disconnect unit from power source.
Electrical shock may cause personal injuries or possibly death.
Never expose eyes or skin to ultraviolet light from any source. e UV purier MUST be DISCONNECTED
from power source before performing maintenance of service. Personal injury may result.
Do not touch lamp glass without gloves. Reduced performance of lamp may result. Clean lamp aer handling.
e UV lamp contains a small quantity of mercury. If a lamp breaks, clean and dispose of with care.
Use only specied replacement lamps with your unit. Use of an incorrect lamp can result in damage to the unit
and/or lamp and will also void the warranty.
When applicable local regulations comprises more restrictive installation and/or certication requirements, the
aforementioned requirements prevail on those of this document and the installer agrees to conform to these at
his own expenses.
When performing installation, servicing or cleaning the UV purier, it is recommended to wear safety glasses
and gloves.
IMPORTANT SAFETY INSTRUCTIONS
Component Warranty
Bio Smart Screen 1 year
WARRANTY
e warranties applicable to the dierent components included in your purchase are as per the table below:
5
Component Qty
Bio Smart Screen 1
5VDC Power Supply 1
20 Ethernet Cable 1
Cable Grommet 1
INCLUDED IN THE BOX
e Bio Smart Screen you purchased comprises the following:
6
INSTALLATION CONSIDERATIONS
Ensure that the site where the Bio Smart Screen will be
located can be supplied with the necessary power
requirements (100-240V @ 50-60Hz). e 5VDC power
supply provided needs to be plugged in a power
outlet.
e suggested temperature range is 4 to 40°C (40 to
105°F). Operating the Bio Smart Screen outside this
range could weaken the bonding material holding the
screen to the plastic enclosure.
e Bio Smart Screen is not weatherproof. If installing
outdoors, the Bio Smart Screen must be installed in a
watertight enclosure and adequate air circulation must
be provided.
Some hardware is not included with the Bio Smart
Screen and will need to be provided by the installer to
complete the installation.
WARNING
Follow all the Safety Instructions outlined in this document and respect all local and federal codes applicable.
7
STEP BY STEP INSTALLATION
1. Select Location
First, select the location of the Bio Smart Screen. In
order to do so, keep in mind that the touchscreen has
to be located near a power outlet and that the Ethernet
cable of 20 provided has to run between the ballast box
and the touchscreen.
You could always consider procuring a longer Ethernet
cable if the 20 provided is not adapted to your
installation. We recommend not using cables longer than
100. Ensure that the cable is a Ethernet cable
straight-through (standard) and not a crossover.
e preferred location for Bio Smart Screen should allow
for an easy access and high visibility, preferably on a wall
at eye level. Environmental conditions, where the Bio
Smart Screen is installed, should be of 4 to 40°C (40 to
105°F) with a non-condensing humidity level.
2. Secure Enclosure to Wall
Separate the front cover from the back cover of the plastic
enclosure that holds the touchscreen. Set aside the front
cover (attached to touchscreen). Depending on the type
of surface you encounter, use the appropriate screws (and
anchors) to secure the back cover to the wall.
By aligning the guiding grooves of the top rst, gently
press in the front cover to reassemble it with the back
cover already axed to the wall with the Sanuvox logo
facing straight.
3. Connect the Ethernet Cable to the Ballast Box
Make sure the power to the ballast box is disconnected
before following the next steps. Remove the cover of the
ballast box. Push in the desired knockout and run the ca-
ble through it and connect it to the Ethernet port located
on the PCB. Insert the grommet around the cable and t
it in the knockout to create a seal. Close the cover of the
ballast box and power ON the UV Bio-Wall Max.
4. Connect the Ethernet Cable and Power Supply to the
Bio Smart Screen
Connect the remaining end of the Ethernet cable to the
Ethernet port of the Bio Smart Screen. Finally, plug in
the power supply into the power outlet and connect the
DC power jack to the Bio Smart Screen female jack.
8
Icons Description
Lamp is ON
Lamp is ON and has been operating for more than 2 years. e lamp should be replaced with a
new one.
Lamp is OFF. e lamp and/or ballast might need to be replaced.
e 2 fans located in the ballast box are not ON. Fans might be jammed or they need to be
replaced.
Exit to previous menu
Settings (select language French or English)
Reset lamp timer upon installing a new lamp
SETTING and USING BIO SMART SCREEN
Once installed, you are ready to use the Bio Smart Screen to gain useful insight on the lamp status and usage. By
touching the Sanuvox home screen you will access the lamp menu.
Here are all the icons you will encounter while using the Bio Smart Screen.
Home Screen
new one.
replaced.
9
Lamp Menu
e lamp menu displays the lamp status icons for each lamp as well as the time that they have been ON.
By clicking on one of the lamp pictogram, you will access the lamp setting menu.
Lamp Setting Menu
is menu will provide you the information on the lamp ID number, the type of lamp that is installed and its status.
Once you have replaced a lamp you can reset the 2 year timer through the lamp setting menu.
Admin Menu
From the lamp setting menu you can access the admin menu by touching the bottom le corner followed by the
right bottom corner of the touchscreen. In the admin menu you’ll be able to change the change the lamp type by
selecting its length and the type (G-germicidal, X-oxidizing and TF-teon coated).
Replacement Parts
Part number Description
BIOSCREEN Bio Smart Screen with power supply, Ethernet cable and installation kit
Other manuals for Bio Smart Screen
1
Table of contents
