Sanyo Denki S-A11KL202B0015SS 00 Series User manual

Lithium-ion Battery UPS
Ver. 3

Online UPS
Double Conversion Online UPS with
Lithium-ion Batteries
UPS unit
-year
warranty
3
Lineup:
[No. of phases/wires]
Input/Output voltage
Output capacity Battery backup time I/O connection UL
certification
Order no. Page
[kVA] [kW] Load power
factor 0.8
Load power
factor 0.7
Specifications Dimensions
[Single-phase 2-wire]
100 Vmodel
100/110/120 V
10.8 13 min 15 min Outlet
−S-A11KL102B0013SSN00(1) p.5 p.8
S-A11KL102B0013US(1)
p.10 p.11
S-A11KL102B0013UJ(1)
1.5 1.2
8 min 10 min
Outlet
−S-A11KL152B0008SSN00(1) p.5 p.8
S-A11KL152B0008US(1)
p.10 p.11
S-A11KL152B0008UJ(1)
19 min 20 min −S-A11KL152B0019SSN00(1) p.5 p.8
100 min 110 min −S-A11KL152B0100TSN00(1)
p.13 p.14
200 min 220 min −S-A11KL152B0200TSN00□□(2)
300 min 330 min −S-A11KL152B0300TSN00□□(2)
400 min 440 min −S-A11KL152B0400TSN00□□(2)
500 min 550 min −S-A11KL152B0500TSN00 p.13 p.15
600 min 660 min −S-A11KL152B0600TSN00
21.6 15 min 16 min Outlet/terminal block −S-A11KL202B0015SS□00(1) p.5 p.8
32.4
9 min 10 min
Outlet/terminal block
−S-A11KL302B0009SS□00(1)
p.7 p.9
19 min 20 min −S-A11KL302B0019SS□00(1)
50 min 55 min −S-A11KL302B0050TS□00(1)
p.13 pp.16, 18
100 min 110 min −S-A11KL302B0100TS□00□□(2)
150 min 165 min −S-A11KL302B0150TS□00□□(2)
200 min 220 min −S-A11KL302B0200TS□00□□(2)
250 min 275 min −S-A11KL302B0250TS□00 p.13 pp.17, 19
300 min 330 min −S-A11KL302B0300TS□00
54
11 min 12 min
Terminal block
−S-A11KL502B0011SST00(1) p.7 p.9
30 min 32 min −S-A11KL502B0030TST00(1)
p.13 p.20
60 min 64 min −S-A11KL502B0060TST00□□(2)
90 min 96 min −S-A11KL502B0090TST00□□(2)
120 min 128 min −S-A11KL502B0120TST00□□(2)
p.13 p.21
150 min 160 min −S-A11KL502B0150TST00
180 min 192 min −S-A11KL502B0180TST00
(1) Vertical (free-standing)/rack-mount convertible (2) Free-standing or rack-mount type can be selected.
2CATALOG No.P1023B006 ‘21.6

Installation examples
Mountable in an EIA standard
19-inch rack
Vertical installation
Rack support rails are optional. You can change the orientation of the
LCD panel.
Refer to the specifications for installation
accessories such as vertical stands and
floor mounting brackets.
Its input voltage ranges from -40% to +20% of the rated voltage
when the load level is less than 70%.
Battery drain can be minimized even in unstable power
environments.
An inverter module is removable from the front of a UPS unit for
easy maintenance.
Its built-in maintenance bypass circuit allows maintenance to be
performed while maintaining inverter power supply.
The A11K-Li achieves an operating temperature range as wide as
-20 to +55°C.
It can be used with confidence even in harsh cold or hot
environments.
With a 0.8 load power factor, the A11K-Li is capable of providing its
power to loads with a high power factor.
Our conventional UPSs(1) using lead-acid batteries require battery
replacement about every 5 years.
Thanks to Li-ion batteries, this UPS doesn't require battery
replacement for 10 years.(2) Thus, the cost of battery replacement
can be reduced.
The volume of the 30-minute backup model is about half of our
conventional products,(1) and it can be installed in a smaller space.
The timing of power on and shutdown of hard drives or servers
can be easily scheduled. (This only applies to models with a
backup time of 19 minutes or less)
Wide Input Range
Easy Maintenance
Wide OperatingTemperature Range Compatible with High Power Factor Loads
Reduced Maintenance Work
Space-Saving
Easy and Reliable Sequential System Start and Stop
●
● ●
●
●
●
●
●
●
● ●
(1) Conventional UPS: A11K (with lead-acid batteries)
(2) At 30°C ambient temperature
Settings can be done with an outlet box; it comes built-in for 1 and 1.5 kVA models, and
optional for 2 and 3 kVA models.
Battery Cold Start Function
Batteries can start up the UPS even when grid AC power is not available, enabling inverter operation.
With this function enabled, the UPS can be used as an emergency power supply in the event of a natural disaster or emergency. Note that the function is disabled by default.
SANUPS SOFTWARE STANDALONE
A free software program (Windows version) that enables the power management
from computers is available for download from our website.
UPS status can be checked at a glance from a PC or server.
Note: This software can only be used on computers in serial connection with UPS.
For power management via a network, we have optional network solutions available.
Main functions
• Automatic start-up/shutdown of computers
• Scheduled operation
• UPS status display
• Message display
• UPS event log
SANUPS SOFTWARE
STANDALONE
Power supply
RS-232C
Output capacity 1.5 kVA 1.2 kW
[Setting example]
Normal
output
power* Controlled output 1
Operating
continuously
Controlled output 2
UPS
starts
Starts
after
30 s
Starts
after
35 s
* When the UPS is off, the output power is stopped.
Operation screen examples
3
CATALOG No.P1023B006 ‘21.6
SANUPS A11K-Li

Views and Part NamesViews and Part Names
1, 1.5 kVA, Rear View
PC Port (RS-232C)
Output Line Control
and Remote Ports
Optional Card Interface
Output Outlet
(NEMA 5-15) Bypass Breaker
Maintenance Bypass Switch
Power Input
Cable (1.8 m)
Maintenance Bypass Breaker
Optional Card Slot
2 kVA, Rear View
PC Port (RS-232C)
Output Line Control
and Remote Ports
Maintenance Bypass Breaker
Optional Card Interface
Main Breaker
Bypass Breaker
Power Input
Cable (1.8 m)
Output Outlet
(NEMA L5-30)
Output Outlet Breaker
(For NEMA 5-15)
Output Outlet
(NEMA 5-15)
Optional Card Slot
Menu Operation Buttons
Inverter ON/STANDBY Button
LCD Panel
Warning LED
Output LED
Backup Time LED
Input Power LED
LCD Screen
Sliding Button Cover Opened (slides up/down)
1, 1.5, 2 kVA, Front View
LCD Panel
Battery backup timeBattery backup time
8to 19min
Note: The photos above may look different from the actual products in the printed text, etc.
2 kVA Terminal Block Type, Rear View
Model: S-A11KL202B0015SST00
Main Breaker
Maintenance Bypass Breaker
Bypass Breaker
I/O Terminal Block
4CATALOG No.P1023B006 ‘21.6
Online UPS SANUPS A11K-Li

Specifications
Order no. S-A11KL102B0013SSN00 S-A11KL152B0008SSN00 S-A11KL152B0019SSN00 S-A11KL202B0015SS□00
Rated output capacity (apparent power / active power) 1 kVA / 0.8 kW 1.5 kVA / 1.2 kW 2 kVA / 1.6 kW
Technology Topology Double conversion online
Rectifier High power factor converter
Cooling method Forced air cooling
Inverter High-frequency PWM
AC input No. of phases/wires Single-phase 2-wire(1)
Rated voltage 100/110/120 V (Same as output voltage)
Voltage range At load level < 70%: Within -40 to +20% of rated voltage (-40% becomes -20% for recovery voltage)
At load level ≥ 70%: Within ±20% of rated voltage
Rated frequency 50/60 Hz (auto-sensing(2))
Frequency range Within ±1, 3, 5, or 7% of rated frequency (same as output frequency regulation)
Required capacity(3) 1.1 kVA 1.5 kVA 2.0 kVA
Input power factor 0.95 or greater 0.95 or greater 0.97 or greater
AC output No. of phases/wires Single-phase 2-wire
Rated voltage 100/110/120 V (User-selectable. Factory setting: 100 V)
Rated current 10 A 15 A 20 A
Voltage regulation Within ±2% of rated voltage (at rated output)
Rated frequency 50/60 Hz (Same as the input rated frequency)
Frequency regulation During grid operation Within ±1, 3, 5, or 7% of the rated frequency (User-selectable. Factory setting: ±3%)
During battery operation Within ±0.5% of rated frequency
Output waveform Pure sine wave
Voltage harmonic
distortion
At linear load 3% or less (At rated output)
At rectifier load 7% or less (At rated output)
Load power factor Rated 0.8 lagging (Variation range: 0.7 lagging to 1.0)
Transient voltage
fluctuation
For abrupt load change Within ±5% of rated voltage (For 0 ⇔100% load step changes at rated input)
For loss or return of input power Within ±5% of rated voltage (At rated output)
For abrupt input voltage change Within ±5% of rated voltage (For ±10% abrupt change)
Overcurrent protection Automatic transfer to bypass (With automatic retransfer function)
Overload capability Inverter 105% (for 200 ms)
Bypass 200% (for 30 s), 800% (for 2 cycles)
Output Line Control Yes An optional outlet box is required
Battery Type Lithium-ion battery
Battery backup time(4) Initial value 13 min (15 min) 8 min (10 min) 19 min (20 min) 15 min (16 min)
After 10 years(5) 11 min (12 min) 6 min (8 min) 16 min (17 min) 12 min (13 min)
Battery self-test Settings possible (Factory setting: "disabled")
Interface PC port RS-232C
Remote port Remote ON/OFF switch (can control up to 5 UPS units in Linked Operation using a dedicated connection cable)
Auxiliary port Output Line Control contact(6)
Dry contact Optional dry contact interface card is required
Network support Optional LAN interface card is required
Acoustic noise During normal operation 41 dB 45 dB 45 dB
During battery operation or at a temperature above 40˚C51 dB 51 dB 51 dB
Heat dissipation (At rated operation, after battery charging completed) 82 W 127 W 153 W
Input leakage current 3 mA 3 mA 3 mA
Operating environment Ambient temperature: -20 to +55°C,(7) humidity: 10 to 90% RH (non-condensing)
Storage environment(8) Temperature: -20 to +55°C, humidity: 10 to 90% RH (non-condensing)
EMC standard VCCI 32-1 Class A
Separate options
Outlet box(9) ―P10030B (outlet type),
P10035B (terminal block type)
Rack support rails(10) RM030-US (2U)
Floor mounting brackets(11) FMA11KA00
Caster base(12) CBA11KA01
Air filter kit(13) FL008-3
(1) If single-wire grounding the AC input and output, set the input/output ground phase according to the
UPS specification. The W (N) terminal of AC input (S phase) and the W (N) terminal of AC output (V
phase) are to be grounded.
(2) The inverter synchronizes operation with AC input and allows uninterrupted transfer through a bypass
circuit provided that the AC input frequency is within a range of the rated frequency ±3% (1, 3, 5, or 7%
selectable) and the AC input voltage is within the rated voltage ±20% (if the load level is less than 70%:
between -40% and +20%).
(3) Max. capacity during battery recovery charging
(4) At 25°C ambient temperature and load power factor of 0.8, using new, fully charged batteries. In paren-
theses are values at 0.7 load power factor.
(5) Assuming 10 power outages per year
(6) For 2 kVA models, settings can be done with an optional outlet box.
(7) Battery charging will stop when battery temperature exceeds 55°C.
(8) Avoid use or storage in +30˚C or higher temperature for extended periods of time, or the battery's life
will be shortened. When storing the UPS for a long period without operating it, the batteries require
recharging once every six months.
(9) Enables Output Line Control, the coordinated on/off management of UPS outlets. "Output 0" is normal
output; "Output 1 (and 2)" is controlled output.
Note that its operating temperature range is different from that of the UPS.
(10) Used for mounting the UPS on a standard 19-inch rack.
(11) Used to secure a free-standing type UPS to the floor.
(12) Used to carry a vertically-installed UPS.
(13) Use an air filter at an ambient temperature of 40°C or lower.
Output capacity 1to 2kVA Battery backup time 8to 19 min
5
CATALOG No.P1023B006 ‘21.6
SANUPS A11K-Li

Battery backup timeBattery backup time
10min
Views and Part NamesViews and Part Names
3 kVA, Rear View
Model: S-A11KL302B0009SSN00
PC Port (RS-232C)
Output Line Control
and Remote Ports
Maintenance Bypass Breaker
Optional Card Slot
Optional Card Interface
Main BreakerBypass Breaker
Output Outlet Breaker (For NEMA 5-15)
Output Outlet
(NEMA 5-15)
Output Outlet
(NEMA L5-30)
Power Input
Cable (1.8 m)
Terminal Block Type, Rear View
Model: S-A11KL302B0009SST00
Output Outlet Breaker
(For NEMA 5-15)
Output Outlet (NEMA 5-15)
Maintenance Bypass Breaker
I/O Terminal Block
Bypass Breaker
Main Breaker
Menu Operation Buttons
Inverter ON/STANDBY Button
LCD Panel
Warning LED
Output LED
Backup Time LED
Input Power LED
LCD Screen
Sliding Button Cover Opened (slides up/down)
Note: The photos above may look different from the actual products in the printed text, etc.
3 kVA, Front View
LCD Panel
5 kVA, Rear View
5 kVA, Front View
PC Port (RS-232C)
Main Breaker
Bypass Breaker
Output Line Control
and Remote Ports
Maintenance Bypass
Breaker Output Outlet Breaker
(For NEMA 5-15)
Optional Card Slot
Optional Card Interface
Output Outlet
(NEMA 5-15)
I/O Terminal Block
LCD Panel
3 kVA, Rear View
Model: S-A11KL302B0019SSN00
PC Port (RS-232C)
Output Line Control
and Remote Ports
Maintenance Bypass Breaker
Optional Card Slot
Optional Card Interface
Main BreakerBypass Breaker
Output Outlet Breaker (For NEMA 5-15)
Output Outlet
(NEMA 5-15)
Output Outlet
(NEMA L5-30)
Power Input
Cable (1.8 m)
Terminal Block Type, Rear View
Model: S-A11KL302B0019SST00
I/O Terminal Block
19min
Battery backup timeBattery backup time
LCD Panel
12min
Battery backup timeBattery backup time
6CATALOG No.P1023B006 ‘21.6
Online UPS SANUPS A11K-Li

Specifications
Order no. S-A11KL302B0009SS□00 S-A11KL302B0019SS□00 S-A11KL502B0011SST00
Rated output capacity (apparent power / active power) 3 kVA / 2.4 kW 5 kVA / 4 kW
Technology Topology Double conversion online
Rectifier High power factor converter
Cooling method Forced air cooling
Inverter High-frequency PWM
AC input No. of phases/wires Single-phase 2-wire(1)
Rated voltage 100/110/120 V (Same as output voltage)
Voltage range At load level < 70%: Within -40 to +20% of rated voltage (-40% becomes -20% for recovery voltage)
At load level ≥ 70%: Within ±20% of rated voltage
Rated frequency 50/60 Hz (auto-sensing(2))
Frequency range Within ±1, 3, 5, or 7% of rated frequency (same as output frequency regulation)
Required capacity(3) 3.0 kVA 5.3 kVA
Input power factor 0.97 or greater 0.97 or greater
AC output No. of phases/wires Single-phase 2-wire
Rated voltage 100/110/120 V (User-selectable. Factory setting: 100 V)
Rated current 30 A 50 A
Voltage regulation Within ±2% of rated voltage (at rated output)
Rated frequency 50/60 Hz (Same as the input rated frequency)
Frequency regulation During grid operation Within ±1, 3, 5, or 7% of the rated frequency (User-selectable. Factory setting: ±3%)
During battery operation Within ±0.5% of rated frequency
Output waveform Pure sine wave
Voltage harmonic
distortion
At linear load 3% or less (At rated output)
At rectifier load 7% or less (At rated output)
Load power factor Rated 0.8 lagging (Variation range: 0.7 lagging to 1.0)
Transient voltage
fluctuation
For abrupt load change Within ±5% of rated voltage (For 0⇔100% load step changes at rated input)
For loss or return of input power Within ±5% of rated voltage (At rated output)
For abrupt input voltage change Within ±5% of rated voltage (For ±10% abrupt change)
Overcurrent protection Automatic transfer to bypass (With automatic retransfer function)
Overload capability Inverter 105% (for 200 ms)
Bypass 200% (for 30 s), 800% (for 2 cycles)
Output Line Control An optional outlet box is required Contact us
Battery Type Lithium-ion battery
Battery backup time(4) Initial value 9 min (10 min) 19 min (20 min) 11 min (12 min)
After 10 years(5) 6 min (8 min) 16 min (17 min) 9 min (10 min)
Battery self-test Settings possible (Factory setting: "disabled")
Interface PC port RS-232C
Remote port Remote ON/OFF switch (can control up to 5 UPS units in Linked Operation using a dedicated connection cable)
Auxiliary port Output Line Control contact(6)
Dry contact Optional dry contact interface card is required
Network support Optional LAN interface card is required
Acoustic noise During normal operation 46 dB 46 dB
During battery operation or at a temperature above 40°C55 dB 55 dB
Heat dissipation (At rated operation, after battery charging completed) 254 W 421 W
Input leakage current 3.5 mA 3.5 mA
Operating environment Ambient temperature: -20 to +55°C,(7) humidity: 10 to 90% RH (non-condensing)
Storage environment(8) Ambient temperature: -20 to +55°C, humidity: 10 to 90% RH (non-condensing)
EMC standard VCCI 32-1 Class A
Separate options
Outlet box(9) P10030B (outlet type),
P10035B (terminal block type) ―
Rack support rails(10) RM027-US (3U) RM028-US (4U)
Floor mounting brackets(11) ―
Caster base(12) CBA11KA01 CBA11KA02
Air filter kit(13) FL009-3 FL010-3
(1) If single-wire grounding the AC input and output, set the input/output ground phase according to the
UPS specification. The W (N) terminal of AC input (S phase) and the W (N) terminal of AC output (V
phase) are to be grounded.
(2) The inverter synchronizes operation with AC input and allows uninterrupted transfer through a bypass
circuit provided that the AC input frequency is within a range of the rated frequency ±3% (1, 3, 5, or 7%
selectable) and the AC input voltage is within the rated voltage ±20% (if the load level is less than 70%:
between -40% and +20%).
(3) Max. capacity during battery recovery charging
(4) At 25°C ambient temperature and load power factor of 0.8, using new, fully charged batteries. In paren-
theses are values at 0.7 load power factor.
(5) Assuming 10 power outages per year
(6) For 3 kVA models, settings can be done with an optional outlet box.
(7) Battery charging will stop when battery temperature exceeds 55˚C.
(8) Avoid use or storage in +30˚C or higher temperature for extended periods of time, or the battery's life
will be shortened. When storing the UPS for a long period without operating it, the batteries require
recharging once every six months.
(9) Enables Output Line Control, the coordinated on/off management of UPS outlets. "Output 0" is normal
output; "Output 1 (and 2)" is controlled output.
Note that its operating temperature range is different from that of the UPS.
(10) Used for mounting the UPS on a standard 19-inch rack.
(11) Used to secure a free-standing type UPS to the floor.
(12) Used to carry a vertically-installed UPS.
(13) Use an air filter at an ambient temperature of 40°C or lower.
Output capacity 3kVA, 5kVA Battery backup time 10 to 19 min
7
CATALOG No.P1023B006 ‘21.6
SANUPS A11K-Li

Order no.(1) Outlet type S-A11KL102B0013SSN00 S-A11KL152B0008SSN00 S-A11KL152B0019SSN00 S-A11KL202B0015SSN00
Terminal block type ―――S-A11KL202B0015SST00
Rated output capacity
(apparent power / active power)
1 kVA / 0.8 kW 1.5 kVA / 1.2 kW 1.5 kVA / 1.2 kW 2 kVA / 1.6 kW
Battery backup time(2) 13 min (15 min) 8 min (10 min) 19 min (20 min) 15 min (16 min)
Battery capacity [Ah·cell] 84 84 180 180
Battery power consumption [Wh] 310 310 666 666
Input plug NEMA 5-15P NEMA 5-15P NEMA 5-15P NEMA L5-30P or M5 terminal
Output outlet NEMA 5-15R ×6 NEMA 5-15R ×6 NEMA 5-15R ×6 NEMA L5-30R ×1 or M5 terminal
NEMA 5-15R ×2 (15 A each)
Acoustic noise During normal operation 41 dB 45 dB 45 dB 45 dB
During battery operation or at a
temperature above 40°C
51 dB 51 dB 51 dB 51 dB
Heat dissipation (At rated operation,
after battery charging completed)
82 W 127 W 127 W 153 W
Input leakage current 3 mA 3 mA 3 mA 3 mA
Operating environment Ambient temperature: -20 to +55°C,(3) humidity: 10 to 90% RH (non-condensing)
Dimensions(4) (Unit: mm)
Drawing Fig.1Fig.1Fig.1Fig.1
W435 435 435 435
H86 (2U) 86 (2U) 86 (2U) 86 (2U)
D440 488 625 625
Mass 17 kg 18 kg 27 kg 27 kg
(1) Vertical/rack-mount convertible
(2) At a 25°C ambient temperature, 0.8 load power factor, using new, fully charged batteries. The values in parentheses are the values at a load power factor of 0.7.
(3) Battery charging will stop when battery temperature exceeds 55˚C.
(4) Dimensions do not include protruding objects like screws.
Dimensions
(191)
Vertical stands (Supplied)
Rack-mounting
bracket (Supplied)
D
W
(480)
H
H
(447)
W
D
Fig. 1
Paint color: Black (Munsell N1.5)
■Input plug shape ■Output outlet shape
NEMA 5-15P NEMA L5-30P NEMA 5-15R NEMA L5-30R
Output capacity 1to 2kVA
8CATALOG No.P1023B006 ‘21.6
Online UPS SANUPS A11K-Li

Fig. 3
Paint color: Black (Munsell N1.5)
(234)
H
W
D
Floor-mounting
bracket (Supplied)
Rack-mounting bracket
(Supplied)
(480)
W
H
D
Rack-mounting bracket
(Supplied)
H
(190)
W
D
(480)
W
H
D
Floor-mounting bracket (Supplied)
Fig. 2
■Input plug shape ■Output outlet shape
NEMA L5-30P NEMA 5-15R NEMA L5-30R
Output capacity 3kVA, 5kVA
Order no.(1) Outlet type S-A11KL302B0009SSN00 S-A11KL302B0019SSN00 ―
Terminal block type S-A11KL302B0009SST00 S-A11KL302B0019SST00 S-A11KL502B0011SST00
Rated output capacity
(apparent power / active power)
3 kVA / 2.4 kW 3 kVA / 2.4 kW 5 kVA / 4 kW
Battery backup time(2) 9 min (10 min) 19 min (20 min) 11 min (12 min)
Battery capacity [Ah·cell] 180 360 360
Battery power consumption [Wh] 666 1332 1332
Input plug NEMA L5-30P or M5 terminal NEMA L5-30P or M5 terminal M5 terminal
Output outlet NEMA L5-30R ×1 or M5 terminal
NEMA 5-15R ×2 (15 A each)
NEMA L5-30R ×1 or M5 terminal
NEMA 5-15R ×2 (15 A each)
M5 terminal
NEMA 5-15R ×2 (15 A each)
Acoustic noise During normal operation 46 dB 46 dB 46 dB
During battery operation or at
a temperature above 40°C
55 dB 55 dB 55 dB
Heat dissipation (At rated operation,
after battery charging completed)
254 W 254 W 421 W
Input leakage current 3.5 mA 3.5 mA 3.5 mA
Operating environment Ambient temperature: -20 to +55°C,(3) humidity: 10 to 90% RH (non-condensing)
Dimensions(4) (Unit: mm)
Drawing Fig. 2 Fig. 3 Fig. 3
W435 435 435
H131 (3U) 175 (4U) 175 (4U)
D625 690 690
Mass 32 kg 47 kg 49 kg
(1) Vertical/rack-mount convertible
(2) At 25°C ambient temperature and load power factor of 0.8, using new, fully charged batteries. In parentheses are values at 0.7 load power factor.
(3) Battery charging will stop when the battery temperature exceeds 55˚C.
(4) Dimensions do not include protruding objects like screws.
9
CATALOG No.P1023B006 ‘21.6
SANUPS A11K-Li

Order no. S-A11KL102B0013US S-A11KL102B0013UJ S-A11KL152B0008US S-A11KL152B0008UJ
UL-registered no. A11KL102U001 A11KL102U001J A11KL152U001 A11KL152U001J
Rated output capacity (apparent power / active power) 1 kVA / 0.8 kW 1.5 kVA / 1.2 kW At 100 V setting: 1.25 kVA / 1.0 kW
At 110 V setting: 1.375 kVA / 1.1 kW
At 120 V setting: 1.5 kVA / 1.2 kW
Technology Topology Double conversion online
Rectifier High power factor converter
Cooling method Forced air cooling
Inverter High-frequency PWM
AC input No. of phases/wires Single-phase 2-wire(1)
Rated voltage 120 V 100/110/120 V
(Same as output voltage)
120 V 100/110/120 V
(Same as output voltage)
Voltage range At load level < 70%: Within -40 to +20% of rated voltage (-40% becomes -20% when returning to grid operation)
At load level ≥ 70%: Within ±20% of rated voltage
Rated frequency 50/60 Hz (auto-sensing(2))
Frequency range Within ±1/3/5/7% of rated frequency (same as output frequency regulation)
Required capacity(3) 1.1 kVA 1.5 kVA
Input power factor 0.95 or greater
AC output No. of phases/wires Single-phase 2-wire
Rated voltage 120 V 100/110/120 V
(User-selectable. Factory
setting: 100 V)
120 V 100/110/120 V
(User-selectable. Factory setting: 100 V)
Rated current 10 A 12.5 A
Voltage regulation Within ±2% of rated voltage (at rated output)
Rated frequency 50/60 Hz (Same as the input rated frequency)
Frequency regulation During grid operation Within ±1/3/5/7% of the rated frequency (User-selectable. Factory setting: ±3%)
During battery operation Within ±0.5% of rated frequency
Output waveform Pure sine wave
Voltage harmonic
distortion
At linear load 3% or less (At rated output)
At rectifier load 7% or less (At rated output)
Load power factor Rated 0.8 lagging (Variation range: 0.7 lagging to 1.0)
Transient voltage
fluctuation
For abrupt load change Within ±5% of rated voltage (For 0⇔100% load step changes at rated input)
For loss or return of input power Within ±5% of rated voltage (at rated output)
For abrupt input voltage change Within ±5% of rated voltage (For ±10% abrupt change)
Overcurrent protection Automatic transfer to bypass (With automatic retransfer function)
Overload capability Inverter 105% (for 200 ms)
Bypass 200% (for 30 s), 800% (for 2 cycles)
Output Line Control Yes
Battery Type Lithium-ion battery
Battery backup time(4) Initial value 13 min (15 min) 8 min (10 min)
After 10 years(5) 11 min (12 min) 6 min (8 min)
Battery self-test Can be enabled (Factory setting:
disabled)
Interface PC port RS-232C
Remote port Remote ON/OFF switch (can control up to 5 UPS units in Linked Operation using a dedicated connection cable)
Dry contact Optional dry contact interface card is required
Network support Optional LAN interface card is required
Acoustic noise During normal operation 41 dB 45 dB
During battery operation or at a temperature above 40˚C 51 dB 51 dB
Heat dissipation (At rated operation, after battery charging completed) 82 W 127 W
Input leakage current 3 mA 3 mA
Operating environment Ambient temperature: -20 to +55°C,(6) humidity: 10 to 90% RH (non-condensing)
Storage environment(7) Temperature: -20 to +55°C, humidity: 10 to 90% RH (non-condensing)
EMC standard FCC Part 15
Subpart B Class A
VCCI 32-1 Class A FCC Part 15
Subpart B Class A
VCCI 32-1 Class A
Separate options
Rack support rails(8) RM030-US (2U)
Floor mounting brackets(9) FMA11KA00
Caster base(10) CBA11KA01
Air filter kit(11) FL008-3
Specifications
UL certified models Output capacity 1kVA, 1.5 kVA
(1) If single-wire grounding the AC input and output, set the input/output ground phase according to the UPS
specification. The W (N) terminal of AC input (S phase) and the W (N) terminal of AC output (V phase) are
to be grounded.
(2) The inverter synchronizes operation with AC input and allows uninterrupted transfer through a bypass
circuit provided that the AC input frequency is within a range of the rated frequency ±3% (1, 3, 5, or 7%
selectable) and the AC input voltage is within the rated voltage ±20% (if the load level is less than 70%:
between -40% and +20%).
(3) Max. capacity during battery recovery charging
(4) At 25°C ambient temperature and load power factor of 0.8, using new, fully charged batteries. In parenthe-
ses are values at 0.7 load power factor.
(5) Assuming 10 power outages per year
(6) Battery charging will stop when the battery temperature exceeds 55˚C.
(7) To extend battery life, avoid use or storage for extended periods of time in environments exceeding +30˚C.
If a UPS is stored without being operated for a long period, the batteries require recharging once every 6
months.
(8) Used for mounting the UPS on a standard 19-inch rack.
(9) Used to secure a free-standing type UPS to the floor.
(10) Used to carry a vertically-installed UPS.
(11) Use an air filter at an ambient temperature of 40°C or lower.
10 CATALOG No.P1023B006 ‘21.6
Online UPS SANUPS A11K-Li

Dimensions
UL certified models Output capacity 1kVA, 1.5 kVA
Order no.(1) Outlet type S-A11KL102B0013US S-A11KL102B0013UJ S-A11KL152B0008US S-A11KL152B0008UJ
Rated output capacity
(apparent power / active power)
1 kVA / 0.8 kW 1.5 kVA / 1.2 kW At 100 V setting: 1.25 kVA / 1.0 kW
At 110 V setting: 1.375 kVA / 1.1 kW
At 120 V setting: 1.5 kVA / 1.2 kW
Battery backup time(2) 13 min (15 min) 8 min (10 min)
Battery capacity [Ah·cell] 80 80
Battery power consumption [Wh] 264 264
Input plug NEMA 5-15P NEMA 5-15P
Output outlet NEMA 5-15R × 6 NEMA 5-15R × 6
Acoustic
noise
During normal operation 41 dB 45 dB
During battery operation or at a
temperature above 40°C
51 dB 51 dB
Heat dissipation (At rated operation,
after battery charging completed)
82 W 127 W
Input leakage current 3 mA 3 mA
Operating environment Ambient temperature: -20 to +55°C,(3) humidity: 10 to 90% RH (non-condensing)
Dimensions(4) (Unit: mm)
Drawing Fig. 1 Fig. 1
W435 435
H86 (2U) 86 (2U)
D440 488
Mass 16 kg 17 kg
(1) Vertical/rack-mount convertible
(2) At 25°C ambient temperature and load power factor of 0.8, using new, fully charged batteries. In parentheses are values at 0.7 load power factor.
(3) Battery charging will stop when the battery temperature exceeds 55˚C.
(4) Dimensions do not include protruding objects like screws.
(191)
Vertical stands (Supplied)
Rack-mounting
bracket (Supplied)
D
W
(480)
H
H
(447)
W
D
Fig. 1
Paint color: Black (Munsell N1.5)
■Input plug shape ■Output outlet shape
NEMA 5-15P NEMA 5-15R
11
CATALOG No.P1023B006 ‘21.6
SANUPS A11K-Li

Menu Operation Buttons
Inverter ON/STANDBY Button
LCD Panel
Warning LED
Output LED
Backup Time LED
Input Power LED
LCD Screen
Sliding button cover Opened (slides up/down)
1.5 kVA, Rear View
PC Port
(RS-232C) Optional Card Interface
Output Outlet (NEMA 5-15)
Bypass Breaker
UPS Unit Connector
Extended Battery
Unit Connector
Maintenance Bypass Switch
Power Input Cable
(1.8 m)
Battery Unit Connector
Maintenance Bypass Breaker
Communication Signal
and Remote Ports
Battery Breaker
Optional Card Slot
UPS unit
Battery Unit
3 kVA, Rear View
PC Port (RS-232C)
Optional Card Interface
Output Outlet Breaker (For NEMA 5-15)
Output Outlet (NEMA 5-15)
Output Outlet (NEMA L5-30)
Main Breaker
Power Input Cable
(1.8 m)
Communication Signal
and Remote Ports
UPS Unit Connector
Extended Battery
Unit Connector
Battery Unit Connector
Maintenance Bypass Breaker
Bypass Breaker
Battery Breaker
UPS Unit
Battery Unit
Optional Card Slot
3 kVATerminal BlockType, Rear View 
Same as above model except
for the part shown below
UPS Unit
Maintenance Bypass Breaker
Main Breaker
Bypass Breaker Optional Card Slot
Output Outlet Breaker
(For NEMA 5-15)
Output Outlet
(NEMA 5-15)
I/O Terminal Block
Note: The photos above may look different from the actual products in the printed text, etc.
5 kVA, Rear View
I/O Terminal Block
Battery Unit Connector
Extended Battery
Unit Connector
Battery Breaker
UPS Unit Connector
Optional Card Slot
Maintenance Bypass Breaker Bypass Breaker
Output Outlet Breaker
(For NEMA 5-15)
Output Outlet (NEMA 5-15)
Main Breaker
PC Port (RS-232C) Communication Signal
and Remote Ports
Optional Card Interface
UPS Unit
Battery Unit
1.5 kVA, Front View
LCD Panel
3 kVA, Front View
LCD Panel
5 kVA, Front View
LCD Panel
Battery backup timeBattery backup time
30to 180min
Battery backup timeBattery backup time
100to 600min
Battery backup timeBattery backup time
50to 300min
Views and Part NamesViews and Part Names
12 CATALOG No.P1023B006 ‘21.6
Online UPS SANUPS A11K-Li

(1) If single-wire grounding the AC input and output, set the input/output ground phase according to the
UPS specification. The W (N) terminal of AC input (S phase) and the W (N) terminal of AC output (V
phase) are to be grounded.
(2) The inverter synchronizes operation with AC input and allows uninterrupted transfer through a bypass
circuit provided that the AC input frequency is within a range of the rated frequency ±3% (1, 3, 5, or 7%
selectable) and the AC input voltage is within the rated voltage ±20% (if the load level is less than 70%:
between -40% and +20%).
(3) Max. capacity during battery recovery charging
(4) At 25°C ambient temperature and load power factor of 0.8, using new, fully charged batteries.
(5) Assuming 10 power outages per year
(6) Battery charging will stop when battery temperature exceeds 55˚C.
(7) To extend battery life, avoid use or storage for extended periods of time in environments exceeding
+30˚C. If a UPS is stored without being operated for a long period, the batteries require recharging
once a year.
(8) Used for mounting a UPS unit or battery unit on a standard 19-inch rack.
(9) Used to secure a free-standing type to the floor.
(10) Use an air filter at an ambient temperature of 40°C or lower.
Order no. (A set of a UPS unit and battery units) S-A11KL152B0□00TSN00□□ S-A11KL302B0□□0TS□00□□ S-A11KL502B0□□0TST00□□
UPS unit model no. A11KL152 A11KL302 A11KL502
Rated output capacity (apparent power / active power) 1.5 kVA / 1.2 kW 3 kVA / 2.4 kW 5 kVA / 4 kW
Technology Topology Double conversion online
Rectifier High power factor converter
Cooling method Forced air cooling
Inverter High-frequency PWM
AC input No. of phases/wires Single-phase 2-wire(1)
Rated voltage 100/110/120 V (Same as output voltage)
Voltage range At load level < 70%: Within -40 to +20% of rated voltage (-40% becomes -20% for recovery voltage)
At load level ≥ 70%: Within ±20% of rated voltage
Rated frequency 50/60 Hz (auto-sensing(2))
Frequency range Within ±1, 3, 5, or 7% of rated frequency (same as output frequency regulation)
Required capacity(3) 1.5 kVA 3.0 kVA 5.3 kVA
Input power factor 0.95 or greater 0.97 or greater
AC output No. of phases/wires Single-phase 2-wire
Rated voltage 100/110/120 V (User-selectable. Factory setting: 100 V)
Rated current 15 A 30 A 50 A
Voltage regulation Within ±2% of rated voltage (at rated output)
Rated frequency 50/60 Hz (Same as the input rated frequency)
Frequency regulation During grid operation Within ±1, 3, 5, or 7% of the rated frequency (User-selectable. Factory setting: ±3%)
During battery operation Within ±0.5% of rated frequency
Output waveform Pure sine wave
Voltage harmonic
distortion
At linear load 3% or less (At rated output)
At rectifier load 7% or less (At rated output)
Load power factor Rated 0.8 lagging (Variation range: 0.7 lagging to 1.0)
Transient voltage
fluctuation
For abrupt load change Within ±5% of rated voltage (For 0⇔100% load step changes at rated input; output switching)
For loss or return of input power Within ±5% of rated voltage (At rated output)
For abrupt input voltage change Within ±5% of rated voltage (For ±10% abrupt change)
Overcurrent protection Automatic transfer to bypass (With automatic retransfer function)
Overload capability Inverter 105% (for 200 ms)
Bypass 200% (for 30 s), 800% (for 2 cycles)
Output Line Control No
Battery Type Lithium-ion battery
Battery backup time(4) Initial value 100/200/300/400/500/600 min 50/100/150/200/250/300 min 30/60/90/120/150/180 min
After 10 years(5) 95/190/285/380/475/570 min 47/95/142/190/237/285 min 28/57/85/114/142/171 min
Battery self-test Settings possible (Factory setting: "disabled")
Interface PC port RS-232C
Remote port Remote ON/OFF switch (can control up to 5 UPS units in Linked Operation using a dedicated connection cable)
Communication signal port Failure/Outage
Dry contact Optional dry contact interface card is required
Network support Optional LAN interface card is required
Acoustic noise During normal operation 45 dB or less 46 dB or less 46 dB or less
During battery operation or at a temperature above 40°C51 dB or less 55 dB or less 55 dB or less (60 dB or less when battery
voltage is low)
Heat dissipation (At rated operation, after battery charging completed) 127 W 254 W 430 W
Input leakage current 3 mA or less 3.5 mA or less 3.5 mA or less
Operating environment Ambient temperature: -20 to +55°C,(6) humidity: 10 to 90% RH (non-condensing)
Storage environment(7) Ambient temperature: -20 to +55°C, humidity: 10 to 90% RH (non-condensing)
EMC standard VCCI 32-1 Class A
Separate options
UPS unit rack support rails(8) RM030-US (2U) RM027-US (3U) RM028-US (4U)
Battery unit rack support rails(8) RM028-US (4U) RM028-US (4U) RM028-US (4U)
Floor mounting brackets (for free-standing type)(9) FMBCA01 FMBCA01 FMBCA01
Air filter kit(10) FL008-3 FL009-3 FL010-3
Battery backup time 30 to 600 min Output capacity 1.5 to 5kVA
Specifications
13
CATALOG No.P1023B006 ‘21.6
SANUPS A11K-Li

Free-standing type Order no.
(A set of a UPS unit and battery units) S-A11KL152B0100TSN00(1)
S-A11KL152B0200TSN00 S-A11KL152B0300TSN00 S-A11KL152B0400TSN00
Rack mount type Order no.
(A set of a UPS unit and battery units) S-A11KL152B0200TSN00RM S-A11KL152B0300TSN00RM S-A11KL152B0400TSN00RM
Rated output capacity
(apparent power / active power)
1.5 kVA / 1.2 kW
Battery backup time(2) 100 min 200 min 300 min 400 min
Battery capacity [Ah·cell] 1104 2208 3312 4416
Battery power consumption [Wh] 2484 4968 7452 9936
Input plug NEMA 5-15P
Output Outlet NEMA 5-15R ×6
Acoustic noise During normal operation 45 dB or less
During battery operation or at
a temperature above 40°C
51 dB or less
Heat dissipation (At rated operation,
after battery charging completed)
127 W
Input leakage current 3 mA or less
Operating environment Ambient temperature: -20 to +55°C,(3) humidity: 10 to 90% RH (non-condensing)
Free-standing type - Dimensions(4) (Unit: mm)
Drawing Fig. 1 Fig. 4 Fig. 5 Fig. 6
W86+175 435 435 435
H435 541 716 891
D520 520 520 520
Mass 66 kg 124 kg 176 kg 228 kg
Rack mount type - UPS unit dimensions(4) (Unit: mm)
Drawing Fig. 2
W435
H1 86 (2U)
D488
Mass 14 kg
Rack mount type - Battery unit dimensions(4) (Unit: mm)
Drawing Fig. 3 ×1Fig.3×2Fig.3×3Fig.3×4
W435 435 435 435
H2 175 (4U) 175 ×2 (8U) 175 ×3 (12U) 175 ×4 (16U)
D520 520 520 520
Mass 52 kg 52 kg ×2 52 kg ×3 52 kg ×4
(1) Vertical/rack-mount convertible
(2) At 25°C ambient temperature and load power factor of 0.8, using new, fully charged batteries.
(3) Battery charging will stop when battery temperature exceeds 55˚C.
(4) Dimensions do not include protruding objects like screws.
H
DW
443
(317.5)
Joining brackets (Supplied)
Joining brackets
(Supplied)
Floor-mounting brackets (Supplied)
Fig. 1
■Input plug shape ■Output outlet shape
NEMA 5-15P NEMA 5-15R
Paint color: Black (Munsell N1.5)
Joining brackets (Supplied)
W
(33) D
175 86
175
25
(80)
H
Fig. 4
(33) DW
86
25
(80)
H
175175175
Joining brackets (Supplied)
Fig. 5
Joining brackets (Supplied)
(33) DW
175 86
175
25
(80) 175175
H
Fig. 6
480
W
Rack-mounting brackets (Supplied)
D
H1H2
Battery unit
UPS unit Fig. 2
Fig. 3
Rack mount type - Rack mounting brackets:
Included but not installed with a 100-minute set.
The 200, 300, and 400-minute sets will be shipped with brackets installed.
Dimensions
Output capacity 1.5 kVA
14 CATALOG No.P1023B006 ‘21.6
Online UPS SANUPS A11K-Li

■Input plug shape ■Output outlet shape
NEMA 5-15P NEMA 5-15R
Paint color: Black (Munsell N1.5)
Output capacity 1.5 kVA
Free-standing type Order no.
(A set of a UPS unit and battery units) S-A11KL152B0500TSN00 S-A11KL152B0600TSN00
Rack mount type Order no.
(A set of a UPS unit and battery units) ――
Rated output capacity
(apparent power / active power)
1.5 kVA / 1.2 kW
Battery backup time(1) 500 min 600 min
Battery capacity [Ah·cell] 5520 6624
Battery power consumption [Wh] 12420 14904
Input plug NEMA 5-15P
Output outlet NEMA 5-15R × 6
Acoustic
noise
During normal operation 45 dB
During battery operation or at a
temperature above 40°C
51 dB
Heat dissipation (At rated operation,
after battery charging completed)
127 W
Input leakage current 3 mA or less
Operating environment Ambient temperature: -20 to +55°C,(2) humidity: 10 to 90% RH (non-condensing)
Free-standing type - Dimensions(3) (Unit: mm)
Drawing Fig. 7 Fig. 8
W435 435 + 435 (+ 65)
H1066 716
D520 520
Mass 286 kg 184 + 170 kg
Rack mount type - UPS unit dimensions(3) (Unit: mm)
Drawing ―
W―
H1 ―
D―
Mass ―
Rack mount type - Battery unit dimensions(3) (Unit: mm)
Drawing ―
W―
H2 ―
D―
Mass ―
(1) At 25°C ambient temperature and load power factor of 0.8, using new, fully charged batteries.
(2) Battery charging will stop when battery temperature exceeds 55˚C.
(3) Dimensions do not include protruding objects like screws.
Joining brackets (Supplied)
(32) DW
175 86
175175175
H
175
25
(80)
Fig. 7
Joining brackets (Supplied)
(32) DW
175
25
(80)
W
630
175175
175
25
(80)
H
86175175
(65)
D
Fig. 8
15
CATALOG No.P1023B006 ‘21.6
SANUPS A11K-Li

Free-standing type Order no.
(A set of a UPS unit and battery units) S-A11KL302B0050TSN00(1)
S-A11KL302B0100TSN00 S-A11KL302B0150TSN00 S-A11KL302B0200TSN00
Rack mount type Order no.
(A set of a UPS unit and battery units) S-A11KL302B0100TSN00RM S-A11KL302B0150TSN00RM S-A11KL302B0200TSN00RM
Rated output capacity
(apparent power / active power)
3 kVA / 2.4 kW
Battery backup time(2) 50 min 100 min 150 min 200 min
Battery capacity [Ah·cell] 1104 2208 3312 4416
Battery power consumption [Wh] 2484 4968 7452 9936
Input plug NEMA L5-30P
Output outlet NEMA L5-30R ×1, NEMA 5-15R ×2 (15 A each)
Acoustic noise During normal operation 46 dB or less
During battery operation or at
a temperature above 40°C
55 dB or less
Heat dissipation (At rated operation,
after battery charging completed)
254 W
Input leakage current 3.5 mA or less
Operating environment Ambient temperature: -20 to +55°C,(3) humidity: 10 to 90% RH (non-condensing)
Free-standing type - Dimensions(4) (Unit: mm)
Drawing Fig. 1 Fig. 4 Fig. 5 Fig. 6
W131+175 435 435 435
H435 586 761 936
D520 520 520 520
Mass 74 kg 132 kg 184 kg 236 kg
Rack mount type - UPS unit dimensions(4) (Unit: mm)
Drawing Fig. 2
W435
H1 131 (3U)
D520
Mass 22 kg
Rack mount type - Battery unit dimensions(4) (Unit: mm)
Drawing Fig. 3 ×1Fig.3×2Fig.3×3Fig.3×4
W435 435 435 435
H2 175 (4U) 175 ×2 (8U) 175 ×3 (12U) 175 ×4 (16U)
D520 520 520 520
Mass 52 kg 52 kg ×2 52 kg ×3 52 kg ×4
(1) Vertical/rack-mount convertible
(2) At 25°C ambient temperature and load power factor of 0.8, using new, fully charged batteries.
(3) Battery charging will stop when battery temperature exceeds 55˚C.
(4) Dimensions do not include protruding objects like screws.
W
443
D
Joining brackets (Supplied)
8
(365)
Floor-mounting bracket (Supplied)
H
Fig. 1
H
175
25
(80)
W
(8) D
131
175
Joining brackets (Supplied)
Fig. 4
H
175
175
175
25
(80)
W
(8) D
131
175
Joining brackets (Supplied)
H
175
175
25
(80) 131
175
(8) DW
Joining brackets (Supplied)
Fig. 5 Fig. 6
■Input plug shape ■Output outlet shape
NEMA L5-30P NEMA 5-15R NEMA L5-30R
H2
W
480
H1
Rack-mounting bracket (Supplied)
Battery unit
UPS unit Fig. 2
Fig. 3
D
Rack mount type - Rack mounting brackets:
Included but not installed with a 50-minute set.
The 100, 150, and 200-minute sets will be shipped with brackets installed.
Output capacity 3kVA
Dimensions
Terminal block type in the next spread
Paint color: Black (Munsell N1.5)
16 CATALOG No.P1023B006 ‘21.6
Online UPS SANUPS A11K-Li

■Input plug shape ■Output outlet shape
NEMA L5-30P NEMA 5-15R NEMA L5-30R
Output capacity 3kVA Terminal block type in the next page
Free-standing type Order no.
(A set of a UPS unit and battery units) S-A11KL302B0250TSN00 S-A11KL302B0300TSN00
Rack mount type Order no.
(A set of a UPS unit and battery units) ––
Rated output capacity
(apparent power / active power)
3 kVA / 2.4 kW
Battery backup time(2) 250 min 300 min
Battery capacity [Ah·cell] 5520 6624
Battery power consumption [Wh] 12420 14904
Input plug NEMA L5-30P
Output outlet NEMA L5-30R × 1, NEMA 5-15R × 2 (15 A each)
Acoustic
noise
During normal operation 46 dB or less
During battery operation or at a
temperature above 40°C
55 dB or less
Heat dissipation (At rated operation,
after battery charging completed)
254 W
Input leakage current 3.5 mA or less
Operating environment Ambient temperature: -20 to +55°C,(2) humidity: 10 to 90% RH (non-condensing)
Free-standing type - Dimensions(3) (Unit: mm)
Drawing Fig. 7 Fig. 8
W435 435 + 435 (+ 65)
H1111 761
D520 520
Mass 294 kg 192 + 170 kg
Rack mount type - UPS unit dimensions(3) (Unit: mm)
Drawing ―
W―
H1 ―
D―
Mass ―
Rack mount type - Battery unit dimensions(3) (Unit: mm)
Drawing ―
W―
H2 ―
D―
Mass ―
(1) At 25°C ambient temperature and load power factor of 0.8, using new, fully charged batteries.
(2) Battery charging will stop when battery temperature exceeds 55˚C.
(3) Dimensions do not include protruding objects like screws.
H
175
175
175
W
(8) D
131
175 175
Joining brackets (Supplied)
W
(80)
25
Fig. 7
Joining brackets (Supplied)
W
175 131175175
W
(8) D
175
630
175175
520
H
25
25
(80) (80)
(65)
Fig. 8
17
CATALOG No.P1023B006 ‘21.6
SANUPS A11K-Li

Output capacity 3kVA Terminal block type
Free-standing type Order no.
(A set of a UPS unit and battery units) S-A11KL302B0050TST00(1)
S-A11KL302B0100TST00 S-A11KL302B0150TST00 S-A11KL302B0200TST00
Rack mount type Order no.
(A set of a UPS unit and battery units) S-A11KL302B0100TST00RM S-A11KL302B0150TST00RM S-A11KL302B0200TST00RM
Rated output capacity
(apparent power / active power)
3 kVA / 2.4 kW
Battery backup time(2) 50 min 100 min 150 min 200 min
Battery capacity [Ah·cell] 1104 2208 3312 4416
Battery power consumption [Wh] 2484 4968 7452 9936
Input terminal M5 terminal
Output terminal and receptacle M5 terminal and NEMA 5-15R ×2 (15 A each)
Acoustic noise During normal operation 46 dB or less
During battery operation or at
a temperature above 40°C
55 dB or less
Heat dissipation (At rated operation,
after battery charging completed)
254 W
Input leakage current 3.5 mA or less
Operating environment Ambient temperature: -20 to +55°C,(3) humidity: 10 to 90% RH (non-condensing)
Free-standing type - Dimensions(4) (Unit: mm)
Drawing Fig. 1 Fig. 4 Fig. 5 Fig. 6
W131+175 435 435 435
H435 586 761 936
D520 520 520 520
Mass 74 kg 132 kg 184 kg 236 kg
Rack mount type - UPS unit dimensions(4) (Unit: mm)
Drawing Fig. 2
W435
H1 131 (3U)
D520
Mass 22 kg
Rack mount type - Battery unit dimensions(4) (Unit: mm)
Drawing Fig. 3 ×1 Fig. 3 ×2 Fig. 3 ×3 Fig. 3 ×4
W435 435 435 435
H2 175 (4U) 175 ×2 (8U) 175 ×3 (12U) 175 ×4 (16U)
D520 520 520 520
Mass 52 kg 52 kg ×2 52 kg ×3 52 kg ×4
(1) Vertical/rack-mount convertible
(2) At 25°C ambient temperature and load power factor of 0.8, using new, fully charged batteries.
(3) Battery charging will stop when battery temperature exceeds 55˚C.
(4) Ignoring screw lengths and the like
■Output outlet shape
NEMA 5-15R
W
443
D
Joining brackets (Supplied)
8
(365)
Floor-mounting brackets (Supplied)
H
Fig. 1
H2
W
480
H1
Rack-mounting brackets (Supplied)
Battery unit
UPS unit Fig. 2
Fig. 3
D
H
175
25
(80)
W
(8) D
131
175
Joining brackets (Supplied)
H
175
175
25
(80) 131
175
(8) DW
Joining brackets (Supplied)
H
175
175
175
25
(80)
W
(8) D
131
175
Joining brackets (Supplied)
Fig. 4 Fig. 5 Fig. 6
Rack mount type - Rack mounting brackets:
Included but not installed with a 50-minute set.
The 100, 150, and 200-minute sets will be shipped with brackets installed.
Dimensions
Paint color: Black (Munsell N1.5)
18 CATALOG No.P1023B006 ‘21.6
Online UPS SANUPS A11K-Li

Output capacity 3kVA Terminal block type
■Output outlet shape
NEMA 5-15R
Paint color: Black (Munsell N1.5)
Free-standing type Order no.
(A set of a UPS unit and battery units) S-A11KL302B0250TST00 S-A11KL302B0300TST00
Rack mount type Order no.
(A set of a UPS unit and battery units) ––
Rated output capacity
(apparent power / active power)
3 kVA / 2.4 kW
Battery backup time(2) 250 min 300 min
Battery capacity [Ah·cell] 5520 6624
Battery power consumption [Wh] 12420 14904
Input plug M5 terminal
Output outlet M5 terminal and NEMA 5-15R × 2 (15 A each)
Acoustic
noise
During normal operation 46 dB or less
During battery operation or at a
temperature above 40°C
55 dB or less
Heat dissipation (At rated operation,
after battery charging completed)
254 W
Input leakage current 3.5 mA or less
Operating environment Ambient temperature: -20 to +55°C,(2) humidity: 10 to 90% RH (non-condensing)
Free-standing type - Dimensions(3) (Unit: mm)
Drawing Fig. 7 Fig. 8
W435 435 + 435 (+ 65)
H1111 761
D520 520
Mass 294 kg 192 + 170 kg
Rack mount type - UPS unit dimensions(3) (Unit: mm)
Drawing ―
W―
H1 ―
D―
Mass ―
Rack mount type - Battery unit dimensions(3) (Unit: mm)
Drawing ―
W―
H2 ―
D―
Mass ―
(1) At 25°C ambient temperature and load power factor of 0.8, using new, fully charged batteries.
(2) Battery charging will stop when battery temperature exceeds 55˚C.
(3) Dimensions do not include protruding objects like screws.
H
175
175
175
W
(8) D
131
175 175
Joining brackets (Supplied)
W
(80)
25
Fig. 7
Joining brackets (Supplied)
W
175 131175175
W
(8) D
175
630
175175
520
H
25
25
(80) (80)
(65)
Fig. 8
19
CATALOG No.P1023B006 ‘21.6
SANUPS A11K-Li

Free-standing type Order no.
(A set of a UPS unit and battery units) S-A11KL502B0030TST00(1)
S-A11KL502B0060TST00 S-A11KL502B0090TST00
Rack mount type Order no.
(A set of a UPS unit and battery units) S-A11KL502B0060TST00RM S-A11KL502B0090TST00RM
Rated output capacity
(apparent power / active power)
5 kVA / 4 kW
Battery backup time(2) 30 min 60 min 90 min
Battery capacity [Ah·cell] 1104 2208 3312
Battery power consumption [Wh] 2484 4968 7452
Input terminal M5 terminal
Output terminal and receptacle M5 terminal and NEMA 5-15R ×2 (15 A each)
Acoustic noise During normal operation 45 dB or less
During battery operation or at a
temperature above 40°C
56 dB or less
When battery voltage is low 60 dB or less
Heat dissipation (At rated operation,
after battery charging completed)
430 W
Input leakage current 3.5 mA or less
Operating environment Ambient temperature: -20 to +55°C,(3) humidity: 10 to 90% RH (non-condensing)
Free-standing type - Dimensions(4) (Unit: mm)
Drawing Fig. 1 Fig. 4 Fig. 5
W175+175 435 435
H435 630 805
D520 520 520
Mass 82 kg 140 kg 192 kg
Rack mount type - UPS unit dimensions(4) (Unit: mm)
Drawing Fig. 2
W435
H1 175 (4U)
D520
Mass 30 kg
Rack mount type - Battery unit dimensions(4) (Unit: mm)
Drawing Fig. 3 ×1Fig.3×2Fig.3×3
W435 435 435
H2 175 (4U) 175 ×2 (8U) 175 ×3 (12U)
D520 520 520
Mass 52 kg 52 kg ×2 52 kg ×3
(1) Vertical/rack-mount convertible
(2) At 25°C ambient temperature and load power factor of 0.8, using new, fully charged batteries.
(3) Battery charging will stop when battery temperature exceeds 55˚C.
(4) Dimensions do not include protruding objects like screws.
W
480
H1H2
Rack-mounting brackets (Supplied)
Battery unit
UPS unit Fig. 2
Fig. 3
D
Joining brackets (Supplied)
25
(80)
H
175175
175
W
(27) D
175
175
175
W
(27) D
175
Joining brackets (Supplied)
p
plied)
25
(80)
H
Fig. 4 Fig. 5
Rack mount type - Rack mounting brackets:
Included but not installed with a 30-minute set.
The 60, 90, and 120-minute sets will be shipped with brackets installed.
Fig. 1
WD
(409)
Floor-mounting brackets (Supplied)
443
8
H
Fig. 1
■Output outlet shape
NEMA 5-15R
Dimensions
Output capacity 5kVA
Paint color: Black (Munsell N1.5)
20 CATALOG No.P1023B006 ‘21.6
Online UPS SANUPS A11K-Li