Sanyo Denki SANUPS A11H User instructions

User Settings Guide
Uninterruptible Power Supply
M0008096

Introduction
Thank you for choosing the SANUPS A11H.
SAVE THESE INSTRUCTIONS
This manual describes the functions and setting operations of the user setting menus. To operate
correctly, read this manual when setting or changing the user setting menus of the UPS. Store this
manual together with the A11H instruction manual in a safe place for convenient reference. Please be
sure to also read the A11H Instruction Manual for details about UPS installation, operation, and
maintenance.
UPS is an abbreviation for Uninterruptible Power Supply.
Table of contents
§1. User Settings........................................................................................................... 1
§1.1 Prior to Modifying the User Settings............................................................ 1
§2. Setup Menu List...................................................................................................... 2
§3. Operation................................................................................................................. 4
§3.1 Output Voltage .............................................................................................. 4
§3.2 Setting Output Frequency Sync Range ....................................................... 5
§3.3 Setting Battery Power Startup Frequency ................................................... 6
§3.4 Setting PC Interface ...................................................................................... 7
§3.5 Setting Serial Baud Rate............................................................................... 8
§3.6 Setting UPS Operation Upon Power Recovery............................................. 9
§3.7 Setting Buzzer Sound .................................................................................... 10
§3.8 Setting UPS Shutdown Operation ................................................................ 11
§3.9 Setting Overload Recovery Operation........................................................... 12
§3.10 Setting UPS Operation at OFF ......................................................... 13
§3.11 Setting Low Battery Voltage Warning Timing............................................ 14
§3.12 Setting Battery Backup Time...................................................................... 15
§3.13 Setting Battery Type.................................................................................... 16
§3.14 Setting Battery Test Schedule..................................................................... 17
§3.15 Resetting Battery Information .................................................................... 18
§3.16 Enabling and Disabling Linked Operation Delay ...................................... 19
§3.17 Setting Linked operation ON delay time.................................................... 20
§3.18 Setting Linked operation OFF delay time .................................................. 21
§3.19 Setting Output line control.......................................................................... 22
§3.20 Setting Outlet box OUTPUT1 ON delay time ............................................ 23
§3.21 Setting Outlet box OUTPUT2 ON delay time ............................................ 24
§3.22 Setting Outlet box OUTPUT1 OFF delay time .......................................... 25
§3.23 Setting Outlet box OUTPUT2 OFF delay time .......................................... 26
§3.24 Setting Outlet box OUTPUT1 power outage output time.......................... 27
§3.25 Setting Outlet box OUTPUT2 power outage output time.......................... 28
§3.26 Setting Operation of Outlet box OUTPUT0 after stopping of
OUTPUT1 and OUTPUT2 .......................................................................... 29
§3.27 Setting Ring signal....................................................................................... 30
§3.28 Resetting the Setting Value......................................................................... 31

1
§
§1 1. . U Us se er r S Se et tt ti in ng gs s
The UPS has a user settings menu, described in §2 “Setup Menu List”. You can set the various menu items
to configure the UPS according to your environment, your applications, and the specifications of the
connected load devices.
§
§1 1. .1 1 P Pr ri io or r t to o M Mo od di if fy yi in ng g t th he e U Us se er r S Se et tt ti in ng gs s
The factory default setting of the UPS is indicated by the “ *” mark in the “Default Setting” column.
Configure each menu according to your environment and requirements.
Whenever you change a menu item setting, we recommend that you place a check mark in the “Current
Setting” column field of the Setup Menu List.
All of the user setting menu items can be selected and set by display LED blinking pattern.
Setup menu list and the blinking pattern of indicators on the control panel are illustrated in the following
figure. For details of setup operations of each menu, see §3.1 to §3.28.
MenuLED SettingLED
No.
Ref.
page Item
Menu Menu LED Setting Setting LED
Default
Setting
Current
Setting
Remarks
‐
●○○○
‐
○●○○
‐
●●○○
1 4 3.1
Output voltage
○
●○○○
120V
○○●○
*
1%
●○○○
3%
○●○○
2 5 3.2 Frequency sync range
(RESTART)
○
○●○○
5%
●●○○
*
Select the menu by the blinking patter
n
of 5 LEDs.
The blinking pattern changes each tim
e
you press .
Pressing this button repeatedly cycle
s
through the LED blinking patterns.
Select the setting by the blinking pattern
of 4 LEDs. The blinking pattern changes
each time you press .
Pressing this button repeatedly cycles
through the LED blinking patterns.


Place a check mark
when you change the
setting.
For the menus indicated by
“RESTART” in this column,
restart of the UPS is required.
The factory default
setting.
• When you change the setting of the menus indicated by RESTART in the “Menu” column, its changes do not take effect
until you restart the UPS. If a restart is required, be sure to power off the load devices before resetting.
See §11.3 “UPS Shutdown (If Not to Be Used for More Than a Week)” in the
A11H Instruction Manual for information
about how to shut down the UPS, and §11.1 “UPS Startup” in the
A11H Instruction Manual for information about how
to start the UPS.
• In this User Settings Guide, the input switch or input breaker is described as MAIN SW for A11H102U or 152U.
MAIN SW indicates MAIN MCCB of A11H202U or 302U.
Note
Indicates the section numbers of
sections with reference information
for each item. See the indicated
sections for detailed information.
● : indicates that LED is blinking.
○ : indicates that LED is off.

2
§
§2 2. . S Se et tu up p M Me en nu u L Li is st t
No.
Ref.
page Item
Menu Menu LED Setting Setting
LED
Default
Setting
Current
Setting Remarks
- ●○○○
Do not use this setting.
- ○●○○
Do not use this setting.
- ●●○○
Do not use this setting.
1 4 3.1 Output voltage
○
●○○○
120 V ○○●○
*
120 V
1% ●○○○
± 1%
3% ○●○○
± 3%
2 5 3.2
Frequency sync
range (RESTART)
○
○●○○
5% ●●○○
*
± 5%
Output frequency variation range (%)
50Hz ●○○○
50Hz
3 6 3.3
Output frequency
(RESTART)
○
●●○○
60Hz ○●○○
*
60Hz
Standalone ●○○○
Set when using UPS remote ON/OFF or Standard OS UPS
Services
Workstation ○●○○
*
Set when using a power management software, LAN card or
UPS remote ON and One-touch system shutdown.
Serial Login
●●○○
Shutdown by serial login.
4 7 3.4 PC interface
○
○○●○
- ○○●○
Do not use this setting.
9600 ●○○○
*
9600 bps.
4800 ○●○○
4800 bps.
5 8 3.5 Serial baud rate
○
●○●○
2400 ●●○○
2400 bps.
Set the serial baud rate when a
workstation, PC, or optional LAN
card is connected.
Auto ●○○○
*
Auto restart
OFF ○●○○
The UPS stays off.
30% ●●○○
Auto restart when battery
charge reaches 30%.
50% ○○●○
Auto restart when battery
charge reaches 50%.
6 9 3.6
UPS operation upon
power recovery
○
○●●○
80% ●○●○
Auto restart when battery
charge reaches 80%.
Specify when to restart the UPS
after a power outage and
shutdown of the UPS due to final
discharge of the batteries.
All patterns
●○○○
*
All sounds
Pattern 1
○●○○
Emit sounds on serious failure and battery trouble.
Pattern 2
●●○○
Emit alarm and key click sounds.
7 10 3.7 Buzzer sound
○
●●●○
OFF
○○●○
Emit key click sounds only.
1 second ●○○○
*
Turn the UPS off when
pressed for 1 second.
3 seconds ○●○○
Turn the UPS off when
pressed for 3 second.
8 11 3.8
Shutdown operation
○
○○○●
Special
operation
●●○○
Turn the UPS off on
special operation.
Set the operation for switch to stop
the UPS power supply.
Auto return ●○○○
Auto recovery when a
certain period of time has
elapsed.
9 12 3.9
Overload recovery
operation
○
●○○●
Bypass ○●○○
*
Fixed as bypass power
supply on overload.
Set the UPS operation after
switching to the bypass power
supply because of overload.
OFF ●○○○
*
The UPS stays off.
10 13 3.10
UPS operation at
OFF
(RESTART)
○
○●○●
Bypass ○●○○
Bypass power supply
Specify the UPS power supply
conditions when is off.
Battery voltage
●○○○
*
When low battery voltage
level is detected.
2 minutes ○●○○
When remaining battery
duration is 2 minutes.
11 14 3.11
Low battery voltage
warning timing
○
●●○●
3 minutes ●●○○
When remaining battery
duration is 3 minutes.
Set the timing of emitting the low
battery voltage warning alarm
(beep, Red BATT. LOW lit).
5 min. 3.5 min.
●○○○
*
20 min.
15 min.
○●○○
30 min.
30 min.
●●○○
40 min.
45 min.
○○●○
60 min.
-
●○●○
Set the UPS backup time on power outage.
An external battery must be connected for settings of 15/20
minutes or higher.
Backup time vary according to UPS model.
A11H102U,152U,202U: 5, 20, 30, 40 or 60 min.
A11H302U: 3.5, 15, 30 or 45 min.
-
○●●○
Do not use this setting.
-
●●●○
Do not use this setting.
-
○○○●
Do not use this setting.
-
●○○●
Do not use this setting.
-
○●○●
Do not use this setting.
12 15 3.12
Battery backup time
○
○○●●
-
●●○●
Do not use this setting.
5 years
●○○○
*
5 years lifetime type
10 years
○●○○
10 years lifetime type
13 16 3.13
Battery type
○
●○●●
3 years
●●○○
3 years lifetime type
Set the battery type. Set this when
you replace the battery or connect an
external battery.
180 days
●○○○
*
Test batteries every 180 days.
90 days
○●○○
Test batteries every 90 days.
30 days
●●○○
Test batteries every 30 days.
14 17 3.14
Battery test schedule
○
○●●●
None ○○●○
No battery check.
Set the interval (number of days)
for the automatic battery check.
The check is carried out
automatically when the specified
number of days has elapsed.
Do not reset
●○○○
*
Do not reset.
15 18 3.15
Reset battery
information
○
●●●●
Reset
○●○○
Reset the battery information when you replace the battery.
● : indicates that LED is blinking.
○ : indicates that LED is off.

3
No.
Ref.
page Item
Menu Menu LED Setting Setting
LED
Default
Setting
Current
Setting Remarks
No delay
●○○○
*
Linked ON/OFF delay disabled
(operate with delay of 0 seconds)
16 19 3.16
Linked delay
operation
●
○○○○
Delay
○●○○
Linked ON/OFF delay enabled
(operate with specified delay)
0 seconds ●○○○ *
10 seconds ○●○○
30 seconds ●●○○
1 minute ○○●○
3 minutes ●○●○
5 minutes ○●●○
10 minutes ●●●○
15 minutes ○○○●
17 20 3.17
Linked operation
ON delay time
●
●○○○
30 minutes ●○○●
0 seconds ●○○○ *
10 seconds ○●○○
30 seconds ●●○○
1 minute ○○●○
3 minutes ●○●○
5 minutes ○●●○
10 minutes ●●●○
15 minutes ○○○●
18 21 3.18
Linked operation
OFF delay time
●
○●○○
30 minutes ●○○●
Set the ON/OFF delay times when
you conduct linked operation.
Delay operation is not enabled
unless item §3.16 “Enabling and
Disabling Linked Operation Delay”
is set to “Delay”.
Set when you connect
a remote switch, or
connect linked
operation cable(s) to
conduct linked
operation.
Disabled ●○○○ * Disable system control
19 22 3.19
Output line control
(Restart)
●
●●○○ Enabled ○●○○ Enable system control
0 seconds ●○○○ *
5 seconds ○●○○
30 seconds ●●○○
1 minute ○○●○
5 minutes ●○●○
20 23 3.20
Outlet box
OUTPUT1
ON delay time
●
○○●○
10 minutes ○●●○
0 seconds ●○○○ *
6 seconds ○●○○
35 seconds ●●○○
1 minute
30 seconds
○○●○
5 minutes
30 seconds
●○●○
21 24 3.21
Outlet box
OUTPUT2
ON delay time
●
●○●○
10 minutes
30 seconds
○●●○
Set the ON delay times for the
OUTPUT1 and OUTPUT2 terminals
of the outlet box.
The delay times are not enabled
unless item §3.19 “Enabling and
Disabling Output line Control” is set
to “Enabled”.
0 seconds ●○○○ *
10 seconds ○●○○
30 seconds ●●○○
1 minute ○○●○
3 minutes ●○●○
22 25 3.22
Outlet box
OUTPUT1
OFF delay time
●
○●●○
5 minutes ○●●○
0 seconds ●○○○ *
10 seconds ○●○○
30 seconds ●●○○
1 minute ○○●○
3 minutes ●○●○
23 26 3.23
Outlet box
OUTPUT2
OFF delay time
●
●●●○
5 minutes ○●●○
Set the OFF delay times for the
OUTPUT1 and OUTPUT2 terminals
of the outlet box.
The delay times are not enabled
unless item §3.19 “Enabling and
Disabling Output line Control” is set
to “Enabled”.
Until batteries
exhausted
●○○○ *
0 seconds ○●○○
30 seconds ●●○○
1 minute ○○●○
3 minutes ●○●○
24 27 3.24
Outlet box
OUTPUT1 power
outage output time
●
○○○●
5 minutes ○●●○
Until batteries
exhausted
●○○○ *
0 seconds ○●○○
30 seconds ●●○○
1 minute ○○●○
3 minutes ●○●○
25 28 3.25
Outlet box
OUTPUT2 power
outage output time
●
●○○●
5 minutes ○●●○
Set the power outage output times
for the OUTPUT1 and OUTPUT2
terminals of the outlet box.
The delay times are not enabled
unless item §3.19 “Enabling and
Disabling Output line Control
”
is set
to “Enabled” and item §3.4 “Setting
PC Interface” is set to “Standalone”.
Stop power
supply
●○○○
*
26 29 3.26
Operation of Outlet
box OUTPUT0
after stopping of
OUTPUT1 and 2
●
○●○●
Continue
power supply
○●○○
Set the operation of OUTPUT0 after
output from the OUTPUT1 and 2
terminals has stopped. This setting
is not enabled unless item§3.19
“Enabling and Disabling Output line
Control” is set to “Enabled”.
Set when you connect
an outlet box to perform
output line control.
Output
●○○○
*
Output a Ring signal when the UPS starts.
27 30 3.27 Ring signal
●
●●○●
Do not output
○●○○ Do not output a Ring signal when the UPS starts.
When you change the setting of the menus indicated by RESTART in the “Menu” column, its changes do not take effect
until you restart the UPS. If a restart is required, be sure to power off the load devices before resetting.
See §11.3 “UPS Shutdown (If Not to Be Used for More Than a Week)” in the
A11H Instruction Manual for information
about how to shut down the UPS, and §11.1 “UPS Startup” in the
A11H Instruction Manual for information about how to
start the UPS.
Note

4
Two beeps are heard. The setting is saved and the UPS returns
to normal operation.
§
§3 3. . O Op pe er ra at ti io on n
§
§3 3. .1 1 O Ou ut tp pu ut t V Vo ol lt ta ag ge e
① Check that the UPS is in the following condition.
② Press and hold it for at least 3 seconds.
③ Check that BACK UP and 50 *4 LEDs are blinking.
*4. If BATT.LOW, 25, or 75 LED is blinking by
accidental operation, quickly press the
(within 3 seconds) several times to switch the
blinking pattern of 4 LEDs surrounded
by
in
the figure below to 50 LED
blinking pattern.
④ Press and hold it for at least 3 seconds.
Blinking of BACK UP LED indicates the output voltage
of the UPS
Blinking of 50 LED indicates 120V.
Setting Setting LED Description
－
● ○ ○ ○
Do not use this setting.
－
○ ● ○ ○
Do not use this setting.
－
● ● ○ ○
Do not use this setting.
120 V
○ ○ ● ○
Output voltage 120V
The output voltage of this UPS is 120V. Do not change
the setting.
Hold for
3 seconds.
Y
ou can check the output voltage setting o
f
this UPS.
Do not change the setting.
MAIN SM on the back panel set to “ON”. *1
The “Green ON/OFF” and
the “Green OUTPUT” are not blinking. *2
*
1. Operation is possible regardless of whether
is ON or OFF.
*2. If these LEDs are blinking, Forced Bypass
switch may be set to “Bypass”. Set this switch to
“Inverter”, and restart the UPS.
*3. Operation is possible even if BATT.LOW, 25, or 75
LED is blinking.
Tip
Press
The UPS switches to the user setting mode.
Buzzer sounds : 2 beeps
： 50 blinks. *3
： BACK UP blinks.
：
LED is off.
：
LED is blinking.
Hold for 3 seconds.

5
Two beeps are heard. The setting is saved and the UPS returns
to normal operation.
§
§3 3. .2 2 S Se et tt ti in ng g O Ou ut tp pu ut t F Fr re eq qu ue en nc cy y S Sy yn nc c R Ra an ng ge e
① Check that the UPS is in the following condition.
② Press and hold it for at least 3 seconds.
③ Quickly press (within 3 seconds) several times to set the 5 LEDs surrounded by in the figure
below to a blinking pattern such as the one in the figure.
④ Quickly press (within 3 seconds) several times to switch to the setting value LED blinking pattern to
select for the 4 LEDs surrounded by in the figure below.
⑤ Press and hold it for at least 3 seconds.
Hold for 3 seconds.
Press
Press
After changing the setting, shut down the UPS, then restart the UPS.
Be sure to power off the load devices before shutting down the UPS.
Note
The blinking pattern changes each time you press or .
If you miss the LED blinking pattern you want to select, continue pressing
the button repeatedly until the LED blinking pattern is redisplayed.
Tip
LEDs that blink when the “3%” setting is selected.
Setting Setting LED
Description
1% ● ○ ○ ○
within ±1% of the rated input frequency
3% ○ ● ○ ○
within ±3% of the rated input frequency
5% ● ● ○ ○
within ±5% of the rated input frequency
Default
setting
MAIN SW on the back panel set to “ON”. *1
The “Green ON/OFF” and
the “Green OUTPUT are not blinking. *2
*
1. Operation is possible regardless of whether
is ON or OFF.
*2. If these LEDs are blinking, Forced Bypass
switch may be set to “Bypass”. Set this switch to
“Inverter”, and restart the UPS.
*3. Operation is possible even if BATT.LOW, 25, or 75
LED is blinking.
Tip
Set the output frequency varitation range(%).
The UPS switches to the user setting mode.
Buzzer sounds : 2 beeps
： 50 blinks. *3
： BACK UP blinks.
：
LED is off.
：
LED is blinking.
Hold for 3 seconds.

6
Two beeps are heard. The setting is saved and the UPS returns
to normal operation.
§
§3 3. .3 3 S Se et tt ti in ng g O Ou ut tp pu ut t F Fr re eq qu ue en nc cy y
① Check that the UPS is in the following condition.
② Press and hold it for at least 3 seconds.
③ Quickly press (within 3 seconds) several times to set the 5 LEDs surrounded by in the figure
below to a blinking pattern such as the one in the figure.
④ Quickly press (within 3 seconds) several times to switch to the setting value LED blinking pattern to
select for the 4 LEDs surrounded by in the figure below.
⑤ Press and hold it for at least 3 seconds.
Hold for 3 seconds.
Press
Press
The blinking pattern changes each time you press or .
If you miss the LED blinking pattern you want to select, continue pressing
the button repeatedly until the LED blinking pattern is redisplayed.
Tip
After changing the setting, shut down the UPS, then restart the UPS.
Be sure to power off the load devices before shutting down the UPS.
Note
LEDs that blink when the “60Hz” setting is selected.
Setting Setting LED Description
50 Hz ● ○ ○ ○
Output frequency: 50Hz
60 Hz ○ ● ○ ○
Output frequency: 60Hz
Set the output frequency of the UPS. Select according to the
environment, or the specification of load devices.
Output frequency is the value selected in this item regardless
of AC power frequency.
Default
setting
MAIN SW on the back panel set to “ON”. *1
The “Green ON/OFF” and
the “Green OUTPUT are not blinking. *2
*
1. Operation is possible regardless of whether
is ON or OFF.
*2. If these LEDs are blinking, Forced Bypass
switch may be set to “Bypass”. Set this switch to
“Inverter”, and restart the UPS.
*3. Operation is possible even if BATT.LOW, 25, or 75
LED is blinking.
Tip
Set the output frequency.
The UPS switches to the user setting mode.
Buzzer sounds : 2 beeps
： 50 blinks. *3
： BACK UP blinks.
：
LED is off.
：
LED is blinking.
Hold for 3 seconds.

7
Two beeps are heard. The setting is saved and the UPS returns
to normal operation.
§
§3 3. .4 4 S Se et tt ti in ng g P PC C I In nt te er rf fa ac ce e
① Check that the UPS is in the following condition.
② Press and hold it for at least 3 seconds.
③ Quickly press (within 3 seconds) several times to set the 5 LEDs surrounded by in the figure
below to a blinking pattern such as the one in the figure.
④ Quickly press (within 3 seconds) several times to switch to the setting value LED blinking pattern to
select for the 4 LEDs surrounded by in the figure below.
⑤ Press and hold it for at least 3 seconds.
Hold for 3 seconds.
Press
Press
LEDs that blink when the “Standalone” setting is selected.
Setting Setting LED Description
Standalone ● ○ ○ ○
Set when using the following functions
・ Standard OS UPS Services
・ UPS remote ON/OFF
Workstation
○ ● ○ ○
Set when using the following functions
・ The power management software
・ LAN Interface card
・ UPS remote ON and One-touch
system shutdown by remote switch
Serial Login
● ● ○ ○ Shutdown by serial login.
－ ○ ○ ● ○ Do not use this setting
Default
setting
The blinking pattern changes each time you press or .
If you miss the LED blinking pattern you want to select, continue pressing
the button repeatedly until the LED blinking pattern is redisplayed.
Tip
MAIN SW on the back panel set to “ON”. *1
The “Green ON/OFF” and
the “Green OUTPUT are not blinking. *2
*
1. Operation is possible regardless of whether
is ON or OFF.
*2. If these LEDs are blinking, Forced Bypass
switch may be set to “Bypass”. Set this switch to
“Inverter”, and restart the UPS.
*3. Operation is possible even if BATT.LOW, 25, or 75
LED is blinking.
Tip
Set the interface mode when using external
interface connector.
The UPS switches to the user setting mode.
Buzzer sounds : 2 beeps
： 50 blinks. *3
： BACK UP blinks.
：
LED is off.
：
LED is blinking.
Hold for 3 seconds.

8
Two beeps are heard. The setting is saved and the UPS
returns to normal operation.
§
§3 3. .5 5 S Se et tt ti in ng g S Se er ri ia al l
B
Ba au ud d R Ra at te e
① Check that the UPS is in the following condition.
② Press and hold it for at least 3 seconds.
③ Quickly press (within 3 seconds) several times to set the 5 LEDs surrounded by in the figure
below to a blinking pattern such as the one in the figure.
④ Quickly press (within 3 seconds) several times to switch to the setting value LED blinking pattern to
select for the 4 LEDs surrounded by in the figure below.
⑤ Press and hold it for at least 3 seconds.
Hold for 3 seconds.
Press
Press
LEDs that blink when the “4800” setting is selected.
Setting Setting LED Description
9600 ● ○ ○ ○ 9600 bps
4800 ○ ● ○ ○ 4800 bps
2400 ● ● ○ ○
2400 bps
Default
setting
The blinking pattern changes each time you press or .
If you miss the LED blinking pattern you want to select, continue pressing
the button repeatedly until the LED blinking pattern is redisplayed.
Tip
MAIN SW on the back panel set to “ON”. *1
The “Green ON/OFF” and
the “Green OUTPUT are not blinking. *2
*
1. Operation is possible regardless of whether
is ON or OFF.
*2. If these LEDs are blinking, Forced Bypass
switch may be set to “Bypass”. Set this switch to
“Inverter”, and restart the UPS.
*3. Operation is possible even if BATT.LOW, 25, or 75
LED is blinking.
Tip
Set the serial baud rate when a workstation, PC,
or optional LAN Interface card is connected.
The UPS switches to the user setting mode.
Buzzer sounds : 2 beeps
： 50 blinks. *3
： BACK UP blinks.
：
LED is off.
：
LED is blinking.
Hold for 3 seconds.

9
Two beeps are heard. The setting is saved and the UPS returns
to normal operation.
§
§3 3. .6 6
S
Se et tt ti in ng g U UP PS S O Op pe er ra at ti io on n U Up po on n P Po ow we er r R Re ec co ov ve er ry y
When using the supplied power management software, you cannot set this menu on the control panel of the
UPS. Set this menu using the power management software. Refer to the User Guide of the power
management software.
① Check that the UPS is in the following condition.
② Press and hold it for at least 3 seconds.
③ Quickly press (within 3 seconds) several times to set the 5 LEDs surrounded by in the figure
below to a blinking pattern such as the one in the figure.
④ Quickly press (within 3 seconds) several times to switch to the setting value LED blinking pattern to
select for the 4 LEDs surrounded by in the figure below.
⑤ Press and hold it for at least 3 seconds.
Hold for
3 seconds.
Press
Press
LEDs that blink when the “30%” setting is selected.
Setting Setting LED
Description
Auto ● ○ ○ ○
The UPS restarts automatically when
the utility power recovers.
OFF ○ ● ○ ○
The UPS stays off when the utility power
recovers. However, when “Bypass” is
selected in §3.10, the UPS supplies the
bypass power.
30% ● ● ○ ○
The UPS restarts automatically, when
battery charge reaches 30% after the
utility power recovers.
50% ○ ○ ● ○
The UPS restarts automatically, when
battery charge reaches 50% after the
utility power recovers.
80% ● ○ ● ○
The UPS restarts automatically, when
battery charge reaches 80% after the
utility power recovers.
After changing the setting, shut down the UPS, then restart the UPS.
Be sure to power off the load devices before shutting down the UPS.
Note
The blinking pattern changes each time you press or .
If you miss the LED blinking pattern you want to select, continue pressing
the button repeatedly until the LED blinking pattern is redisplayed.
Tip
Default
setting
Specify the UPS operation when power
recovers after the UPS stops due to
final discharge of the batteries during a
power outage.
When using the power management software,
the LEDs may blink as shown in the left figure.
You cannot set on the control panel of the UPS.
Change the setting using the power management
software.
MAIN SW on the back panel set to “ON”. *1
The “Green ON/OFF” and
the “Green OUTPUT are not blinking. *2
*
1. Operation is possible regardless of whether
is ON or OFF.
*2. If these LEDs are blinking, Forced Bypass
switch may be set to “Bypass”. Set this switch to
“Inverter”, and restart the UPS.
*3. Operation is possible even if BATT.LOW, 25, or 75
LED is blinking.
Tip
The UPS switches to the user setting mode.
Buzzer sounds : 2 beeps
： 50 blinks. *3
： BACK UP blinks.
：
LED is off.
：
LED is blinking.
Hold for 3 seconds.

10
Two beeps are heard. The setting is saved and the UPS returns
to normal operation.
§
§3 3. .7 7 S Se et tt ti in ng g B Bu uz zz ze er r S So ou un nd d
① Check that the UPS is in the following condition.
② Press and hold it for at least 3 seconds.
③ Quickly press (within 3 seconds) several times to set the 5 LEDs surrounded by in the figure
below to a blinking pattern such as the one in the figure.
④ Quickly press (within 3 seconds) several times to switch to the setting value LED blinking pattern to
select for the 4 LEDs surrounded by in the figure below.
⑤ Press and hold it for at least 3 seconds.
Hold for 3 seconds.
Press
LEDs that blink when the “Pattern 1” setting is selected.
Setting Setting LED
Description
All
patterns
● ○ ○ ○
Emit beeps to power outage, overload,
alarm, serious failure, battery warning,
battery test, battery test result error,
bypass operation, and emit key click
sounds.
Pattern 1
○ ● ○ ○
Emit beeps at serious failure, battery
warning, and emit key click sounds.
Pattern 2
● ● ○ ○
Emit beeps at alarm, and emit key click
sounds.
OFF ○ ○ ● ○
Emit key click sounds only.
The blinking pattern changes each time you press or .
If you miss the LED blinking pattern you want to select, continue pressing
the button repeatedly until the LED blinking pattern is redisplayed.
Tip
Default
setting
Select the conditions under which the UPS emits
the buzzer sound.
MAIN SW on the back panel set to “ON”. *1
The “Green ON/OFF” and
the “Green OUTPUT are not blinking. *2
*
1. Operation is possible regardless of whether
is ON or OFF.
*2. If these LEDs are blinking, Forced Bypass
switch may be set to “Bypass”. Set this switch to
“Inverter”, and restart the UPS.
*3. Operation is possible even if BATT.LOW, 25, or 75
LED is blinking.
Tip
Press
The UPS switches to the user setting mode.
Buzzer sounds : 2 beeps
： 50 blinks. *3
： BACK UP blinks.
：
LED is off.
：
LED is blinking.
Hold for 3 seconds.

11
Two beeps are heard. The setting is saved and the UPS returns
to normal operation.
§
§3 3. .8 8 S Se et tt ti in ng g U UP PS S S Sh hu ut td do ow wn n O Op pe er ra at ti io on n
① Check that the UPS is in the following condition.
② Press and hold it for at least 3 seconds.
③ Quickly press (within 3 seconds) several times to set the 5 LEDs surrounded by in the figure
below to a blinking pattern such as the one in the figure.
④ Quickly press (within 3 seconds) several times to switch to the setting value LED blinking pattern to
select for the 4 LEDs surrounded by in the figure below.
⑤ Press and hold it for at least 3 seconds.
Hold for 3 seconds.
Press
LEDs that blink when the “3 seconds” setting is selected.
Setting Setting LED Description
1 second
● ○ ○ ○
The UPS stops when pressed for
1 second.
3 seconds
○ ● ○ ○
The UPS stops when pressed for
3 seconds.
Special
operation
● ● ○ ○
Press and hold for approximately
3 seconds and then release the button
when the buzzer starts beeping.
Pressing for at least 3 seconds
while the buzzer is beeping shuts down
the UPS.
This setting is the function to prevent shutdown of the UPS by
an accidental operation. This setting is available for shutdown
operation only.
Default
setting
The blinking pattern changes each time you press or .
If you miss the LED blinking pattern you want to select, continue pressing
the button repeatedly until the LED blinking pattern is redisplayed.
Tip
Set the shutdown operation for switch to
stop the UPS. This operation is only valid for the
shutdown operation. The startup operation
cannot be changed.
MAIN SW on the back panel set to “ON”. *1
The “Green ON/OFF” and
the “Green OUTPUT are not blinking. *2
*
1. Operation is possible regardless of whether
is ON or OFF.
*2. If these LEDs are blinking, Forced Bypass
switch may be set to “Bypass”. Set this switch to
“Inverter”, and restart the UPS.
*3. Operation is possible even if BATT.LOW, 25, or 75
LED is blinking.
Tip
Press
The UPS switches to the user setting mode.
Buzzer sounds : 2 beeps
： 50 blinks. *3
： BACK UP blinks.
：
LED is off.
：
LED is blinking.
Hold for 3 seconds.

12
Two beeps are heard. The setting is saved and the UPS returns
to normal operation.
§
§3 3. .9 9 S Se et tt ti in ng g O Ov ve er rl lo oa ad d R Re ec co ov ve er ry y O Op pe er ra at ti io on n
① Check that the UPS is in the following condition.
② Press and hold it for at least 3 seconds.
③ Quickly press (within 3 seconds) several times to set the 5 LEDs surrounded by in the figure
below to a blinking pattern such as the one in the figure.
④ Quickly press (within 3 seconds) several times to switch to the setting value LED blinking pattern to
select for the 4 LEDs surrounded by in the figure below.
⑤ Press and hold it for at least 3 seconds.
Hold for 3 seconds.
Press
Press
LEDs that blink when the “Bypass” setting is selected.
Setting Setting LED
Description
Auto
return
● ○ ○ ○
The UPS returns to UPS power supply
operation automatically after a certain
time has elapsed. *1
Bypass ○ ● ○ ○
The UPS continues bypass power
supply operation when overload
condition persists. Then the UPS
switches to UPS power supply when
the overload is resolved. *2
*1. The UPS switches to UPS power supply operation every 2.5
seconds, and switches back to bypass power supply if the
overload condition still persists. This cycle is repeated.
*2. If the utility power voltage is low and the load current is
below the overload detection threshold when the UPS
switches to bypass power supply, the UPS continues to
switch between UPS power supply and bypass power
supply.
Default
setting
The blinking pattern changes each time you press or .
If you miss the LED blinking pattern you want to select, continue pressing
the button repeatedly until the LED blinking pattern is redisplayed.
Tip
Set the conditions for automatic switch back
to the UPS power supply (auto return) after
switching to the bypass power supply
because of overload.
MAIN SW on the back panel set to “ON”. *1
The “Green ON/OFF” and
the “Green OUTPUT are not blinking. *2
*
1. Operation is possible regardless of whether
is ON or OFF.
*2. If these LEDs are blinking, Forced Bypass
switch may be set to “Bypass”. Set this switch to
“Inverter”, and restart the UPS.
*3. Operation is possible even if BATT.LOW, 25, or 75
LED is blinking.
Tip
The UPS switches to the user setting mode.
Buzzer sounds : 2 beeps
： 50 blinks. *3
： BACK UP blinks.
：
LED is off.
：
LED is blinking.
Hold for 3 seconds.

13
Two beeps are heard. The setting is saved and the UPS returns
to normal operation.
§
§3 3. .1 10 0 S Se et tt ti in ng g U UP PS S O Op pe er ra at ti io on n a at t
O
OF FF F
① Check that the UPS is in the following condition.
② Press and hold it for at least 3 seconds.
③ Quickly press (within 3 seconds) several times to set the 5 LEDs surrounded by in the figure
below to a blinking pattern such as the one in the figure.
④ Quickly press (within 3 seconds) several times to switch to the setting value LED blinking pattern to
select for the 4 LEDs surrounded by in the figure below.
⑤ Press and hold it for at least 3 seconds.
Hold for 3 seconds.
Press
LEDs that blink when the “Bypass” setting is selected.
Setting Setting LED Description
OFF
● ○ ○ ○
When UPS is stopping by the UPS
stays off and the power is not supplied.
Bypass
○ ● ○ ○
When UPS is stopping by the UPS
supplies the bypass power.
Default
setting
The blinking pattern changes each time you press or .
If you miss the LED blinking pattern you want to select, continue pressing
the button repeatedly until the LED blinking pattern is redisplayed.
Tip
Specify the UPS power supply conditions
when the UPS is stopped by the procedure in
§11.2 “UPS Shutdown (Daily)” in the
A11H
Instruction Manual
.
After changing the setting, shut down the UPS, then restart the UPS.
Be sure to power off the load devices before shutting down the UPS.
Note
MAIN SW on the back panel set to “ON”. *1
The “Green ON/OFF” and
the “Green OUTPUT are not blinking. *2
*
1. Operation is possible regardless of whether
is ON or OFF.
*2. If these LEDs are blinking, Forced Bypass
switch may be set to “Bypass”. Set this switch to
“Inverter”, and restart the UPS.
*3. Operation is possible even if BATT.LOW, 25, or 75
LED is blinking.
Tip
Press
The UPS switches to the user setting mode.
Buzzer sounds : 2 beeps
： 50 blinks. *3
： BACK UP blinks.
：
LED is off.
：
LED is blinking.
Hold for 3 seconds.

14
Two beeps are heard. The setting is saved and the UPS returns
to normal operation.
§
§3 3. .1 11 1 S Se et tt ti in ng g L Lo ow w B Ba at tt te er ry y V Vo ol lt ta ag ge e W Wa ar rn ni in ng g T Ti im mi in ng g
When using the supplied power management software, you cannot set this menu on the control panel of the
UPS. Set this menu using the power management software. Refer to the User Guide of the power
management software.
① Check that the UPS is in the following condition.
② Press and hold it for at least 3 seconds.
③ Quickly press (within 3 seconds) several times to set the 5 LEDs surrounded by in the figure
below to a blinking pattern such as the one in the figure.
④ Quickly press (within 3 seconds) several times to switch to the setting value LED blinking pattern to
select for the 4 LEDs surrounded by in the figure below.
⑤ Press and hold it for at least 3 seconds.
Hold for 3 seconds.
Press
Press
LEDs that blink when the “3 minutes” setting is selected.
Setting Setting LED Description
Battery
voltage
● ○ ○ ○
Warning is emitted (Alarm buzzer
sounds and BATT.LOW lights) when
low battery voltage level is detected.
2 minutes ○ ● ○ ○
Warning is emitted when remaining
battery duration is 2 minutes.
3 minutes ● ● ○ ○
Warning is emitted when remaining
battery duration is 3 minutes.
The buzzer does not sound when “OFF” or “Pattern 2” is selected as the
setting value in §3.7 “Setting Buzzer Sound”.
If you are using the power management software, the above setting is
disabled and the warning is emitted at the timing set for performing
UPS shutdown in the power management software.
The blinking pattern changes each time you press or .
If you miss the LED blinking pattern you want to select, continue pressing
the button repeatedly until the LED blinking pattern is redisplayed.
Tip
Default
setting
When using the power management
software, the LEDs may blink as shown
in the left figure. You cannot set on the control
panel of the UPS. Change the setting using
the power management software.
Set the timing of emitting the low
battery voltage warning.
MAIN SW on the back panel set to “ON”. *1
The “Green ON/OFF” and
the “Green OUTPUT are not blinking. *2
*
1. Operation is possible regardless of whether
is ON or OFF.
*2. If these LEDs are blinking, Forced Bypass
switch may be set to “Bypass”. Set this switch to
“Inverter”, and restart the UPS.
*3. Operation is possible even if BATT.LOW, 25, or 75
LED is blinking.
Tip
The UPS switches to the user setting mode.
Buzzer sounds : 2 beeps
： 50 blinks. *3
： BACK UP blinks.
：
LED is off.
：
LED is blinking.
Hold for 3 seconds.

15
§
§3 3. .1 12 2 S Se et tt ti in ng g B Ba at tt te er ry y B Ba ac ck ku up p T Ti im me e
① Check that the UPS is in the following condition.
② Press and hold it for at least 3 seconds.
③ Quickly press (within 3 seconds) several times to set the 5 LEDs surrounded by in the figure
below to a blinking pattern such as the one in the figure.
④ Quickly press (within 3 seconds) several times to switch to the setting value LED blinking pattern to
select for the 4 LEDs surrounded by in the figure below.
⑤ Perform the steps 3 to 5 in §3.15 “Resetting
Battery Information”.
Press
Press
LEDs that blink when the “20 or 15 minutes” setting is selected.
Setting Setting LED
Description
5 min. ● ○ ○ ○
20 min. ○ ● ○ ○
30 min.
● ● ○ ○
40 min. ○ ○ ● ○
60 min. ● ○ ● ○
Set the UPS backup time on power outage.
Select setting of 20 minutes or higher
when the external battery box
connected.
－ ○ ● ● ○
－ ● ● ● ○
－ ○ ○ ○ ●
－ ● ○ ○ ●
－ ○ ● ○ ●
－ ● ● ○ ●
Do not use these settings.
Setting Setting LED
Description
3.5 min. ● ○ ○ ○
15 min. ○ ● ○ ○
30 min.
● ● ○ ○
45 min. ○ ○ ● ○
Set the UPS backup time on power outage.
Select setting of 15 minutes or higher
when the external battery box
connected.
－ ● ○ ● ○
～
－ ● ● ○ ●
Do not use these settings.
Select the backup time according to the connected external battery box.
When the 20minutes battery box is connected, “ 20 minutes” must be
selected. Even if “40 minutes” is selected, the actual backup time
cannot be extended to 40 minutes.
The blinking pattern changes each time you press or .
If you miss the LED blinking pattern you want to select, continue pressing
the button repeatedly until the LED blinking pattern is redisplayed.
Tip
Default
setting
Set the UPS backup time when a battery box is
connected.
Proceed to §3.15 “Resetting Battery Information”
⇒ page 18
After changing the setting, perform the steps 3 to 5 in §3.15
“Resetting Battery Information”. This setting does not take
effect until the battery information is reset. Do not perform the
procedure above except in the battery replacement.
Note
MAIN SW on the back panel set to “ON”. *1
The “Green ON/OFF” and
the “Green OUTPUT are not blinking. *2
*
1. Operation is possible regardless of whether
is ON or OFF.
*2. If these LEDs are blinking, Forced Bypass
switch may be set to “Bypass”. Set this switch to
“Inverter”, and restart the UPS.
*3. Operation is possible even if BATT.LOW, 25, or 75
LED is blinking.
Tip
The UPS switches to the user setting mode.
Buzzer sounds : 2 beeps
： 50 blinks. *3
： BACK UP blinks.
：
LED is off.
：
LED is blinking.
Hold for 3 seconds.
A
A
1
11 1H H1 10 02 2U U
,
,1 15 52 2U U
,
,2 20 02 2U U
A
A
1
11 1H H3 30 02 2U U
Default
setting

16
§
§3 3. .1 13 3 S Se et tt ti in ng g B Ba at tt te er ry y T Ty yp pe e
① Check that the UPS is in the following condition.
② Press and hold it for at least 3 seconds.
③ Quickly press (within 3 seconds) several times to set the 5 LEDs surrounded by in the figure
below to a blinking pattern such as the one in the figure.
④ Quickly press (within 3 seconds) several times to switch to the setting value LED blinking pattern to
select for the 4 LEDs surrounded by in the figure below.
⑤ Perform the steps 3 to 5 in §3.15 "Resetting Battery Information”.
Press
Press
LEDs that blink when the “10 years” setting is selected.
Setting Setting LED Description
5 years
● ○ ○ ○
5 years lifetime type
10 years
○ ● ○ ○
10 years lifetime type
3 years
● ● ○ ○
3 years lifetime type
Select the battery type according to the type of the mounted
battery. When the 5 years lifetime type battery is mounted, “5
years” must be selected. Even if “10 years” is selected, the
actual battery service life cannot be extended to 10 years.
Default
setting
The blinking pattern changes each time you press or .
If you miss the LED blinking pattern you want to select, continue pressing
the button repeatedly until the LED blinking pattern is redisplayed.
Tip
Set the battery type. Set this when you replace
the battery or connect an external battery.
Proceed to §3.15 “Resetting Battery Information” ⇒ page 18
After changing the setting, perform the steps 3 to 5 in §3.15 “Resetting
Battery Information”. This setting does not take effect until the battery
information is reset. Do not perform the procedure above except in the
battery replacement.
Note
MAIN SW on the back panel set to “ON”. *1
The “Green ON/OFF” and
the “Green OUTPUT are not blinking. *2
*
1. Operation is possible regardless of whether
is ON or OFF.
*2. If these LEDs are blinking, Forced Bypass
switch may be set to “Bypass”. Set this switch to
“Inverter”, and restart the UPS.
*3. Operation is possible even if BATT.LOW, 25, or 75
LED is blinking.
Tip
The UPS switches to the user setting mode.
Buzzer sounds : 2 beeps
： 50 blinks. *3
： BACK UP blinks.
：
LED is off.
：
LED is blinking.
Hold for 3 seconds.

17
Two beeps are heard. The setting is saved and the UPS returns
to normal operation.
§
§3 3. .1 14 4 S Se et tt ti in ng g B Ba at tt te er ry y T Te es st t S Sc ch he ed du ul le e
When using the supplied power management software, you cannot set this menu on the control panel of the
UPS. Set this menu using the power management software. Refer to the User Guide of the power
management software.
① Check that the UPS is in the following condition.
② Press and hold it for at least 3 seconds.
③ Quickly press (within 3 seconds) several times to set the 5 LEDs surrounded by in the figure
below to a blinking pattern such as the one in the figure.
④ Quickly press (within 3 seconds) several times to switch to the setting value LED blinking pattern to
select for the 4 LEDs surrounded by in the figure below.
⑤ Press and hold it for at least 3 seconds.
Hold for 3 seconds.
Press
Press
LEDs that blink when the “90 days” setting is selected.
Setting Setting LED Description
180 days ● ○ ○ ○
Check batteries every 180 days.
90 days ○ ● ○ ○
Check batteries every 90 days.
30 days ● ● ○ ○
Check batteries every 30 days.
None ○ ○ ● ○
No battery check.
Default
setting
The blinking pattern changes each time you press or .
If you miss the LED blinking pattern you want to select, continue pressing
the button repeatedly until the LED blinking pattern is redisplayed.
Tip
Set the interval (number of days) for the automatic
battery test. The test is carried out automatically
when the specified number of days has elapsed.
MAIN SW on the back panel set to “ON”. *1
The “Green ON/OFF” and
the “Green OUTPUT are not blinking. *2
*
1. Operation is possible regardless of whether
is ON or OFF.
*2. If these LEDs are blinking, Forced Bypass
switch may be set to “Bypass”. Set this switch to
“Inverter”, and restart the UPS.
*3. Operation is possible even if BATT.LOW, 25, or 75
LED is blinking.
Tip
The UPS switches to the user setting mode.
Buzzer sounds : 2 beeps
： 50 blinks. *3
： BACK UP blinks.
：
LED is off.
：
LED is blinking.
Hold for 3 seconds.

18
Two beeps are heard. The setting is saved and the UPS returns
to normal operation.
§
§3 3. .1 15 5 R Re es se et tt ti in ng g B Ba at tt te er ry y I In nf fo or rm ma at ti io on n
① Check that the UPS is in the following condition.
② Press and hold it for at least 3 seconds.
③ Quickly press (within 3 seconds) several times to set the 5 LEDs surrounded by in the figure
below to a blinking pattern such as the one in the figure.
④ Quickly press (within 3 seconds) several times to switch to the setting value LED blinking pattern to
select for the 4 LEDs surrounded by in the figure below.
⑤ Press and hold it for at least 3 seconds.
Hold for 3 seconds.
Press
Press
LEDs that blink when the “Reset” setting is selected.
Setting Setting LED Description
Do not reset
● ○ ○ ○
Do not reset.
Reset ○ ● ○ ○
Reset the battery information.
Reset the battery information (remaining life, accumulated
battery operating time, number of power outages, battery
exhaustion LED indicator), when you replace the battery.
Default
setting
The blinking pattern changes each time you press or .
If you miss the LED blinking pattern you want to select, continue pressing
the button repeatedly until the LED blinking pattern is redisplayed.
Tip
The battery information should be reset when the
battery is replaced. If resetting is performed
accidentally, the alarm of the remaining battery
service life is not emitted correctly.
MAIN SW on the back panel set to “ON”. *1
The “Green ON/OFF” and
the “Green OUTPUT are not blinking. *2
*
1. Operation is possible regardless of whether
is ON or OFF.
*2. If these LEDs are blinking, Forced Bypass
switch may be set to “Bypass”. Set this switch to
“Inverter”, and restart the UPS.
*3. Operation is possible even if BATT.LOW, 25, or 75
LED is blinking.
Tip
The UPS switches to the user setting mode.
Buzzer sounds : 2 beeps
： 50 blinks. *3
： BACK UP blinks.
： LED is off.
：
LED is blinking.
Hold for 3 seconds.