Sartorius BioPAT Xgas Vis User manual

Operating Manual
BioPAT®Xgas Vis
Software Manual
85037-545-79

Contents
Operating Manual BioPAT®Xgas Vis 3
Contents
1 About This Document....................................................5
1.1 Accompanying Documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
1.2 Symbols Used.........................................................6
2 Safety Information .......................................................7
2.1 General Safety Precautions ...........................................7
2.2 Intended Use and Foreseeable Misuse ...............................7
3 Overview.................................................................8
3.1 Requirements .........................................................8
3.2 Contents of Delivery ..................................................9
4 Installation ..............................................................10
4.1 Installation Steps.....................................................10
4.2 Hardware Installation ................................................12
5 Software Installation ....................................................14
5.1 Preparation Steps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
5.2 BioPAT®Xgas Vis Software ...........................................19
5.3 Perle Device Driver...................................................24
5.4 TruePort Application ................................................ 28
6 Hardware Settings ......................................................32
6.1 CheckingJumperSettingsatthePerleDevice ......................32
6.2 Reseting Perle Device................................................33

Contents
4 Operating Manual BioPAT®Xgas Vis
7 Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
7.1 Perle Device......................................................... 34
7.2 Serial Port ............................................................41
7.2.1 Configuring Serial Port with TruePort Management Tool.....41
7.2.2 Configuring Serial Port with Device Manager.................47
7.3 BioPAT®Xgas Vis OPC License......................................49
7.4 BioPAT®Xgas Sensor.................................................51
7.4.1 Configuring One Sensor......................................51
7.4.2 Configuring Multiple Sensors with
oneEthernetModbusConverter ...........................56
7.5 Changing the Modbus Address.....................................58
8 Installation of BioPAT®Xgas OPC Server................................61
8.1 Installing MFCS/win OPC Client.....................................61
8.2 Configuring MFCS/win Configuration Management ............... 62
8.3 Browsing the BIOPATXGAS.OPC.1 Server with OPC Test Client.... 69
9 Firmware Version .......................................................72
9.1 Checking|UpgradingFirmwareVersionofthePerleDevice.........72
9.2 Configuring Settings forWindows ModbusService ..................76
10 Troubleshooting ........................................................78

Operating Manual BioPAT®Xgas Vis 5
About This Document
1 About This Document
All information and instructions in this operating manual have been compiled
in consideration of applicable standards and guidelines, the state of
technology and our many years of experience and knowledge.
These operating instructions provide you with all the information necessary
toinstallandtoconfiguretheBioPAT®Xgas Vis Software.
In addition to the operating manual, all generallyvalid, legal and otherwise
binding regulations for accident protection and environmental protection
ofthecountryofusemustbeobserved.
The operating manual must always be kept at the place of use of the device.
1.1 Accompanying Documents
The operating manual describes how to install and to configure
theBioPAT®XgasVisSoftware.
In addition to these operating instructions, follow the information in
theoperatingmanual“BioPAT®Xgas” and in the documentation of
theothersoftwareandhardwarecomponents.

6 Operating Manual BioPAT®Xgas Vis
About This Document
1.2 Symbols Used
NOTE
−is an indication of a function or setting on the device.
−is an indication that caution should be exercised while working.
−identifies useful information.
The following presentations will also be used:
– Texts that follow this mark are lists.
tTexts that follow this mark describe activities that must be carried out
inthespecifiedorder.
y Texts that follow this mark describe the result of an action.
““ Texts in quotes are references to other chapters or sections.
[→] Texts following this symbol make reference to other chapters,
sectionsordocuments.

Operating Manual BioPAT®Xgas Vis 7
Safety Information
Safety Information
2 Safety Information
2.1 General Safety Precautions
The BioPAT®Xgas Vis Software may only be installed and configured after
gaining familiaritywith this operating manual.
Always keep the operating manual in the location where the device is in use.
In addition to the operating manual, follow all general and local regulations
for accident prevention and environmental protection.
2.2 Intended Use and Foreseeable Misuse
The operational safety of the device is only ensured when it is used for
itsintendedpurposeandoperatedbytrainedpersonnel.
Application
The device is only intended for industrial, commercial, training, and research
facilities.
The BioPAT®Xgas Vis Software is intended for use with the BioPAT®Xgas
Sensor and the BioPAT®MFCS/win Software.

8 Operating Manual BioPAT®Xgas Vis
Overview
Overview
3 Overview
With the BioPAT®Xgas hardware, the O2and CO2concentration can be
monitored and controlled for any given bioprocesses in real time.
The BioPAT®Xgas is a dual oxygen-carbon dioxide sensor featuring automatic
compensation for humidity and pressure. The oxygen concentration can be
measuredinarangeof1–50%andthecarbondioxideconcentration
inarangeof0–10%.
The BioPAT®Xgas Sensor can be directly connected by analog signals to
theDCUsystem.Therefore,onlyacableandtwofreeanaloginputportsat
the DCU systems need to be available.
Alternatively, if there are no available analog input ports on the DCU system,
then it is possible to connect the BioPAT®Xgas hardware using the BioPAT®
XgasVis Software interfacing to the MFCS/win SCADA software. Herein,
thedirectconnectionoftheBioPAT®Xgas Sensors to the MFCS/win software
with all necessary hardware and software components is described.
3.1 Requirements
−The BioPAT®Xgas Vis Software requires MFCS/winVersion 3.0
−The Firmware version of the used Perle device is minimum 4.5

Operating Manual BioPAT®Xgas Vis 9
Overview
Overview
Computer Configuration
General CD ROM drive
USB Port
Operating
System
Microsoft Windows XP (32 bit)
Microsoft Windows Server 2003 R2 (32 bit & 64 bit)
Microsoft Windows 7 (32 bit & 64 bit)
Microsoft Windows Server 2008 SP2 (32 bit & 64 bit)
Microsoft Windows Server 2008 R2 Sp1 64 bit
Operating
System
Language
English,German
3.2 Contents of Delivery
The delivery of the BioPAT®Xgas Vis Software contains the following
components:
−CD-ROM, containing all necessary software items
−Software activation Dongle
−User Manual for the BioPAT®Xgas Vis

10 Operating Manual BioPAT®Xgas Vis
Installation
4 Installation
4.1 Installation Steps
The following table presents an overview on the necessary steps to install and
configure the BioPAT®Xgas Vis Software. Please follow the recommended
order in the table step by step.
Eachentryreferstoaseparatechapterorsub-chapterinthishandbook
where the procedure is described in detail.
Step Installation Procedure Remark
0Hardwareinstallation[→4.2,page12]
1 Preparation step for installation onWindows
XPandWindowsServer2008,only[→5.1,
page14]
Only for Windows
XP and Windows
Server 2008
2 Software installation of BioPAT®Xgas Vis
Software[→5.2,page19]
3 Installation and configuration of the Perle
devicedriver[→5.3,page24]
4 Installation ofTruePort application
[→5.4,page28]
5 Checking hardware jumper settings at
thePerledevice[→6.1,page32]
6ResetPerledevice[→6.2,page33]
7ConfigurePerledevice[→7.1,page34]
8 Configure serial port with TruePort
ManagementTool[→7.2.1,page41]

Operating Manual BioPAT®Xgas Vis 11
Installation
Step Installation Procedure Remark
9 Configure serial port with Device Manager
[→7.2.2,page47]
10 Activate the BioPAT®Xgas Vis OPC License
[→7.3,page49]
11 Configuration of one BioPAT®Xgas sensor
[→7.4.1,page51]
12 Configuration of multiple sensors with
oneEthernetModbusConverter[→7.4.2,
page56]
13 How to change the Modbus Address
[→7.5,page58]
Multiple sensors
only
14 Installation of BioPAT®Xgas OPC Server
[→8,page61]
15 Installation of MFCS/win OPC Client
[→8.1,page61]
16 Configuration work inside MFCS/win
ConfigurationManagement[→8.2,
page62]
17 How to browse the BIOPATXGA.OPC.1
ServerwithOPCTestClient[→8.3,
page69]
Optional
18 How to check|upgrade the firmware version
ofthePerledevice[→9.1,page72]
Update only
necessary,
iffirmware<4.5
19 Configure settings for Windows Modbus
Service[→9.2,page76]

12 Operating Manual BioPAT®Xgas Vis
Installation
4.2 Hardware Installation
t Install the BioPAT®Xgasaccordingtheoperatingmanual“BioPAT®Xgas”,
delivered togetherwith the BioPAT®Xgas hardware.
− Theinstallationisdescribedinchapter“4.Installation”.
Connection of BioPAT®Xgas to BioPAT®MFCS/win with BioPAT®Xgas Vis Software

Operating Manual BioPAT®Xgas Vis 13
Installation
Accessories
The following articles are available for the BioPAT®Xgas Vis Software:
Article
Number Description Remark
BPX0009 BioPAT®Xgas Vis
Software
Can be used with one MFCS/
win server system.
BPX00(11-15) BioPAT®Xgas Sensor Includes power supply & cable
and article number depends on
vessel size and corresponding
gas flow path.
BPX0018 PC connection
package (includes
Ethernet|Modbus
converter and Bus
termination)
One is needed for each DCU
system or independent vessel
fittedwithBioPAT®Xgas [see
figureinchapter→6.2,
page 33].
BB-34147295 Serial Modbus
Connection cable 2 m
Onecable(2mor5m)isneeded
to connect each sequential
BioPAT®Xgas unit.
BB-34147298 Serial Modbus
Connection cable 5 m

14 Operating Manual BioPAT®Xgas Vis
Software Installation
Software Installation
5 Software Installation
5.1 Preparation Steps
ForWindows XP, only
t Start“:\DotNetFX35SP1\dotNetFx35setup.exe”fromtheXGAS-CD.
NOTE
NETFramework3.5.1mustbeinstalledmanuallyfromtheBioPAT®Xgas VIS CD.
t OpenWindowsExplorerandbrowsetotheCDintothedirectory.
t Doubleclickthefile“:\DotNetFX35SP1\dotNetFx35setup.exe”.

Operating Manual BioPAT®Xgas Vis 15
Software Installation
Software Installation
t Files will be extracted.
t Acceptthetermsandpress“Install”button.
t Press“Exit”button.
t Continuewithchapter[→5.2,page19].

16 Operating Manual BioPAT®Xgas Vis
Software Installation
Software Installation
ForWindows Server 2008 R2, only
NOTE
NETFramework3.5.1mustbeactivatedforWindowsServer2008.
− WindowsServer2008includesthenecessary.Netframework.
Followthestepsbelowinordertoactivatethe.Netframework.
t Goto“AdministrativeTools”.
t Startthe“ServerManager”.
t Open“Roles/Features”.
t Click“AddFeatures”.

Operating Manual BioPAT®Xgas Vis 17
Software Installation
Software Installation
t Expand“.NETFramework3.5.1Features”.
t Select“.NETFramework3.5.1”.
t Clickonthe“Next”button.

18 Operating Manual BioPAT®Xgas Vis
Software Installation
Software Installation
y “ConfirmInstallationSelection”opens.
t Pressbutton“Install”.
y The installation is completed; the installation
message“Installationsucceeded”isdisplayed.
t Click“Close”button.

Operating Manual BioPAT®Xgas Vis 19
Software Installation
Software Installation
5.2 BioPAT®Xgas Vis Software
This chapter describes the installation of the BioPAT®Xgas Vis Software.
NOTE
Please consider that MFCS/win must have been already installed.
Please note, the installation of this software requires local administrative
rights.
The CD-ROM containing the BioPAT®Xgas Vis Software is labeled as
“BioPAT®XgasVisSoftware”.AseparateprogramnamedSETUP.EXE
performs the software installation.
The following steps describe the installation on your computer system.
Installing the BioPAT®Xgas Vis Software
t Shutdown the MFCS/win system from the MFCS/win Shell.
t Insert the CD-ROM into the CD drive.
t Open the windows explorer and change to the CD drive.
t Double-clickonfileSETUP.EXEtostarttheinstallationprogram.
t Ifthe“.NetFramework3.5”isnotinstalled,thenthefollowingdialog
willbeshownonthescreen.

20 Operating Manual BioPAT®Xgas Vis
Software Installation
Software Installation
t Pressthebutton“Accept”tocontinue.
t The welcome screen is shown.
t Pressbutton“Next”.