SAS 8722 Operator's manual

The NIOSH approval label will be printed on the carton.
8722 NIOSH
N95 Particulate Respirator
With exhalation valve
User’s Instruction Manual
SAS Safety Corp.®
3031 Gardenia Avenue, Long Beach, CA 90807, U.S.A.
Phone: [phone]
N95: 95% filter efficiency level,
Effective against particulate aerosol
free of oil
ATTENTION: READ APPLICATIONS, LIMITATIONS
AND FITTING INSTRUCTIONS ON BOX BEFORE
RESPIRATOR IS WORN.
CONTENTS: 12 Respirators

 Exhalation valve reduces hot air build up for easy breathing
 Contours to natural face shape while minimizing pressure points
 Comfortable soft seal foam cushions the nose bridge
 Metal-free, non-toxic disposable mask
 Latex-free head strap
APPLICATIONS
USE AGAINST:
NIOSH approved for protection against particulate aerosols free of oils.
SAS recommends this respirator for use against particulates such as flour, iron coal and
minerals.
This respirator offers nuisance level relief from organic vapors that are below the Permissible
Exposure Limit (PEL). Nuisance level refers to concentrations not exceeding the OSHA PEL or
other government occupational exposure limits, whichever is lower.
DO NOT USE AGAINST:
1. Vapors, paint spray, oil-based aerosols, asbestos and sand blasting.
2. Any contaminant whose concentration is unknown, or immediately dangerous to life.
3. Concentrations of Dust and Mists which exceed the maximum use concentration or 10
times contaminant’s permissible exposure limit established by OSHA.
WARNING:
1. These respirators do not supply oxygen. Use only in well ventilated areas containing
sufficient oxygen to support life.
2. Leave contaminated area immediately if the respirator becomes damaged and proper fit
cannot be obtained or breathing becomes difficult. Dispose and change the respirator.
IMPORTANT LIMITATIONS:
1. All instructions and warnings have to be followed. Failure to do so will reduce the
efficiency of respirator and cause sickness or death.
2. Training on the proper use of respirator must be provided by the employer in accordance
with the safety and health standard.
3. Before occupational use of this respirator a written respiratory protection program must be
implemented meeting all the local government requirements. In the United States
employers must comply with OSHA 29 CFR 1910.134 which includes medical evaluation,
training, and fit testing.
4. Do not alter or modify the respirator.

5. Not suitable for persons with beard or other facial hair which may reduce the efficiency of
respirator.
6. The use and reuse of this respirator is subject to consideration of hygiene damage and
increased breathing resistance. For dirty workplaces, service time should not be extended
beyond 8 total hours of use.
7. Store the respirators in cool place. Avoid direct exposure of sunlight during storage as the
filter media in this respirator can be degraded by extended exposure to direct sunlight.
8. S - Special or critical User Instructions: The model 8722 filtering facepiece respirator has
been manufactured by JINFUYU INDUSTRIAL CO. LTD. For SAS SAFETY CORP
under TC-84A-7721.
ASBESTOS WARNING: DO NOT use this respirator for protection against the inhalation
of asbestos.
SILICA WARNING: SAS Safety respiratory products are not designed to protect you
from the inhalation of silica while performing, observing, or working in or around
sandblasting operations. DO NOT enter any potential exposure area until you know the
nature and concentration of the atmosphere and are wearing appropriate respiratory and
other protection for that exposure situation.
Instructions for the 8722 N95
Maintenance free respirator
Fitting Instructions
The respirator user must be fit tested according to OSHA regulation 29 CFR 1910.134.
1. Hold the respirator in one hand with the nose area at your fingertips, allowing the headbands
to hang below your hand.
2. Press the respirator against your face with the nose foam on the bridge of your nose.
3. Place the top band high on the back of your head. Move the bottom band over your head and
position it below your ears.
4. Test the fit. Cup both hands over the respirator and inhale vigorously. If no negative
pressure is felt inside the respirator, readjust the position of the respirator according to steps
#2, #3, and #4 till get a better fit.

If you CANNOT achieve a proper fit, DO NOT enter the contaminated area.
See your supervisor for proper fitting respiratory protection.