SAT OptimFlush SATOFSHFS2 User manual

SAT OptimFlush SATOFSHFS2 2021/07
OptimFlush
Floor-standing Rimless Toilet
INSTALLATION INSTRUCTIONS
SATOFSHFS2

2
SAT OptimFlush SATOFSHFS2 2021/07
2x 2x 2x
3x 3x3x
1x 1x 1x
TO ENSURE THIS PRODUCT IS INSTALLED PROPERLY, PLEASE READ THESE INSTRUCTIONS
CAREFULLY BEFORE YOU BEGIN.
∅ 10
G1/2"
=
VASELINE
SANITARY SILICONE
CERTAIN
INSTALLATIONS
MAY REQUIRE
PROFESSIONAL
HELP
PRODUCT IS FRAGILE.
TO AVOID BREAKAGE
AND POSSIBLE INJURY
HANDLE WITH CARE!

3
SAT OptimFlush SATOFSHFS2 2021/07
5 sec
BEFORE YOU START ASSEMBLY
1 2 3 4
46 6

4
SAT OptimFlush SATOFSHFS2 2021/07
2
∅10 mm
60 mm
2x
3
2x
4
2x
5
2x
1
180 mm
55 mm
260 mm
!
TOILET INSTALLATION
NOTE: Mounting surface must be clean and level before toilet is installed!

5
SAT OptimFlush SATOFSHFS2 2021/07
12
10
2x
11
98
67
G1/2"
!
VASELINE
814
13
SANITARY SILICONE
3x
!

6
SAT OptimFlush SATOFSHFS2 2021/07
2
∅10 mm
60 mm
2x
4
1
TOILET INSTALLATION
NOTE: Mounting surface must be clean and level before toilet is installed!
3
2x
5
2x
2x

7
SAT OptimFlush SATOFSHFS2 2021/07
6 7
8
2x
9
G1/2"
10 11
12
3x
!
!
8
13
SANITARY SILICONE
VASELINE

8
SAT OptimFlush SATOFSHFS2 2021/07
14
3x
15
!
18
2x
2x
16 17
19
COVER / SEAT INSTALLATION

9
SAT OptimFlush SATOFSHFS2 2021/07
TROUBLESHOOTING GUIDE
Problem Possible Cause Corrective Action
1Toilet flushing fail Toilet angle valve not open. Open the angle valve completely.
The button fail to work. Replace button.
The Regulator filter blocked. Disassembly the regulator to clean filter
and keep press the button 4 minutes to
refill air into cartridges.
2Toilet flushing is weak or
water seal is abnormal
Water pressure too low. Working pressure not less than 20 PSI.
The Regulator filter blocked. Disassembly the regulator to clean filter
and keep press the button 4 minutes to
refill air into cartridges.
Dirty water causes the fill valve core
blocked and limited flow rate.
Replace fill valve.
3Toilet leaking Dirty water causes the flush valve core
seal damage and not close as normal.
Replace flush valve core.
Dirty water causes hydraulic button fail
to close.
Replace hydraulic button.
4Toilet leakage Dirty water cause regulator damage and
leaking.
Replace regulator.
Dirty water causes fill valve damage and
leaking.
Replace fill valve.
The water supply hose not lock well. Lock water supply hose tight enough.
Hose washer damaged or lost. Replace washer.
5Toilet seat fail in slow down The damper fail. Replace seat.
413 mm
592 mm
490 mm
413 mm
DIMENSIONS

10
SAT OptimFlush SATOFSHFS2 2021/07
OFS TOILET PARTS
1Adjuster button
2Regulator
3Fill valve
4Flush valve
5Water outlet pipe
6Cartridges
7Toilet seat
8Flush button
9Chinaware
1
2
3
4
5
7
8
9
6

11
SAT OptimFlush SATOFSHFS2 2021/07
REPAIR PARTS LIST
No Part Name Part Number Usage
1
Adjuster button NDSATOFSHFS2AB 1
2
Regulator 999910060150 1
3
Fill valve 112070031020 1
4
Flush valve deck & core 112070031023
NDSATOFSHFS2FV 1
5
Water outlet pipe NDSATOFSHFS2OP 1
6
Cartridges NDSATOFSHFS2CA 1
7
Toilet seat NDSATOFSHFS2SE 1
8
Hydraulic flush button 112070031021 1
9
Chinaware -
ceramic toilet NDSATOFSHFS2WC 1

12
SAT OptimFlush SATOFSHFS2 2021/07
DECLARATION OF PERFORMANCE
SAT® is registered trademark of
Swiss Aqua Technologies AG
Gewerbestrasse 9, 6330 Cham, Switzerland
www.swatec.ch
PATENT
PROTECTED
OptimFlush Toilet is patented by
Swiss Aqua Technologies AG.