Satechi DUAL DOCK STAND User manual

5Gbps 10Gbps
DP
4K/60Hz
HDMI
4K/60Hz
HDMI
4K/60Hz 10Gbps
5Gbps
ON OFF
ON OFF ON OFF
Slide the power switch to the left from red to green in order to turn on the Dock.
White LED will turn on signifying the dock is on
3
If using with a host device other than a MacBook, slide the aluminum cable cover down to release the cables.
Both cables must be connected in order for full functionality
2
Connect the dual cable connectors to the dual USB-C ports on your host device.
Both cables must be connected in order for full functionality
1
QUICK GUIDE
DUAL DOCK STAND
DOCKING STATION WITH NVME SSD ENCLOSURE

Dock supports only two display outputs maximum.
10Gbps
DP
4K/60Hz
HDMI
4K/60Hz
HDMI
4K/60Hz 10Gbps
5Gbps
UP TO
10 Gbps
Use the USB-C port and USB-A port for data transfer – up
to 10 Gbps each.
Does not support charging or CD readers, including Apple
SuperDrive
9
5Gbps 10Gbps
DP
4K/60Hz
HDMI
4K/60Hz
HDMI
4K/60Hz
10Gbps
5Gbps
UP TO
5 Gbps
Use the USB-C port and USB-A port for data transfer – up
to 5 Gbps each.
Does not support charging or CD readers, including Apple
SuperDrive
8
5Gbps 10Gbps
DP
4K/60Hz
Connect an RJ45 Ethernet cable to the dock’s Gigabit
Ethernet port.
Up to 1 Gbps
7
UP TO
1 Gbps
5Gbps 10Gbps
DP
4K/60Hz
HDMI
4K/60Hz
HDMI
4K/60Hz 5Gbps
UP TO
4K/60Hz
Use DisplayPort cable to connect to a DisplayPort-enabled
monitor.
DisplayPort connection supports up to 4K/60Hz. Dual
monitors supported when using HDMI port to the left of
USB-C data port
6
5Gbps 10Gbps
DP
4K/60Hz
HDMI
4K/60Hz
HDMI
4K/60Hz 5Gbps
UP TO
4K/60Hz
Use HDMI cables to connect up to two HDMI-enabled
monitors.
Dual Display not supported on M1/M2 MacBooks
5
HDMI
4K/60Hz
HDMI
4K/60Hz 10Gbps
5Gbps
ON OFF
UP TO
75W
Use the USB-C PD port to charge your device up to 75W.
~15W is used for the docks operation
USB-C charging port does not support video output or
data transfer
4
PORTS AND CONNECTORS
output

Not compatible with SSDs with preinstalled heat-sinks.
Use the included screw and screwdriver to secure the SSD
into place.
To avoid stripping the screw, please do not over tighten.
5
1. INSERT
2. PUSH
Insert the SSD (not included) at an angle and faceup with
the pins aligned and push down to align the SSD with the
screw hole.
4
Remove the film from both sides of the included thermal
pad and align the holes on the thermal pad with the screw
openings.
3
To install the SSD, press and lift the latch on the SSD cover.
2
5Gbps 10Gbps
DP
4K/60Hz
HDMI
4K/60Hz
HDMI
4K/60Hz 10Gbps
5Gbps
ON OFF
Before installing, ensure the Dual Dock Stand is not connected to power.
Disconnect from host device and disconnect any power delivery cables connected to the Dock
1
INSTALLING SSD

If using with a new Solid-State Drive, please ensure the drive is properly formatted
to support your host device operating system.
5Gbps 10Gbps
DP
4K/60Hz
HDMI
4K/60Hz
HDMI
4K/60Hz 10Gbps
5Gbps
ON OFF
ON OFF ON OFF
Slide the power switch to the left from red to green in order to turn on the Dock.
White LED will turn on signifying the dock is on
1
HDMI
4K/60Hz
HDMI
4K/60Hz 10Gbps
5Gbps
ON OFF
Connect Dual Dock Stand to the power source.
9
Connect the dual cable connectors to the dual USB-C ports
on your host device.
Both cables must be connected in order for full functionality
8
Turn the dock over and place your host device on top of the
Dock Stand.
7
CLICK!
Reinstall the SSD cover. Insert at an angle and press down
until it clicks.
6
Include instruction to eject any external storage device prior to connecting or
disconnecting power to the dock.