Panasonic EBL128 4550 Installation guide

Panasonic Electric Works Nordic AB
Jungmansgatan 12, SE-211 19 Malmö, Sweden
Tel: [phone] •Fax: [phone]
[email protected]wg.panasonic.com •www.panasonic-fire-security.com
Fire alarm system
EBL128
4550
EBL128, an intelligent analog addressable fire alarm system for up to 128 addresses
Auto generation of the Site Specific Data for easier c.i.e. programming
Analog addressable system
EBL128 is an intelligent, analog and
addressable Control and Indicating Equip-
ment for fire detection and fire alarm systems
for buildings, which conforms to the EN54-2
and the EN54-4 standards. It meets the most
stringent requirements in order to secure real
fire alarms and to reduce nuisance alarms.
Features / functions
A user-friendly PC software Win128 is used
to create, edit, download and upload
(backup) the Site Specific Data (SSD).
An SSD Auto generation function is
included in Win128. The units that are
connected to EBL128 can be identified and
the SSD can be auto generated with default
settings and be edited before the download.
Some other features / functions:
Compensation for contamination, i.e.
analog smoke detectors have constant
sensitivity in spite of any contamination.
A Service signal will be given when a
detector has to be replaced.
Advanced alarm algorithms are used
to filter the nuisance alarms from the
real fire alarms and one algorithm is
used for detection of smouldering fires.
User related functions, e.g. Test mode,
Disablements, Alert annunciation, Fire
door closing, Interlocking combinations
of outputs & inputs, Time channels, Co-
incidence alarm, User definable text
message for each alarm point, etc.
Programmable inputs and outputs. In
the c.i.e. and/or via I/O units on the
COM loop. A large number of trigger
conditions are available.
Outputs for routing equipment. Fire
alarm, Fault and Power supply.
Socket for an optional RS485
transceiver component to provide an
interface for up to four ext. Fire Brigade
Panels, Ext. Presentation Units and/or
Alert Annunciation Units.
Interface (RS232) for a PC (Win128)
Interface (RS232) and power supply for
Web-server 1598.
Optional RS485 transceiver 4552, provides
an interface for up to four display units.
Optional expansion boards 458x mounted in
an exp. board holder 4551 provides 8 zone
line inputs and 8 relay outputs respectively.
Up to 128 addresses
The EBL128 c.i.e. has one COM loop for
connection of the loop units (address 001-
127). Each loop unit uses one address.
Some loop units that can be connected:
Analog heat & smoke detectors
Addressable manual call points
Addressable short circuit isolators
Addressable input and output units (to
which e.g. conventional detectors and
manual call points can be connected)
Addressable sirens & sounder bases
Addressable external power supply units
Miscellaneous
The cabinet has a space for two sealed
Lead-Acid batteries (2x12 V, 16-18 Ah).
EBL128 is intended for indoor use and in
dry premises.

All technical features and data are subject to changes without notice, resulting from continuous development and improvement.
Product Leaflet
Date of issue
Revision / Date of revision
MEW00503
2006-04-04
4 / 2010-09-30
Type numbers
4550
EBL128 c.i.e. (128 addresses). Batteries are not included.
4552
RS485 transceiver component, for up to four display units, i.e. Ext. Fire Brigade
Panels 1826 / 1828, Ext. Presentation Unit 1728 and/or Alert Annunciation Units
1735 / 1736.
4551
Expansion board holder. (For two 4580 and two 4581 expansion boards.)
4580
8 zones expansion board.
4581
8 relays expansion board.
4513
Cabinet for drawings. (Similar to the EBL128 cabinet.)
The 4580 board can be used to connect conventional detectors and manual call points to
EBL128. An end-of-line capacitor (470 nF) shall be connected in the last alarm point on each
zone line.
More information is available in the EBL128 Planning Instructions & Operating Instructions.
Technical data
Voltage
primary (V AC)
secondary (V DC)
normal
by battery backup
230
24
21 - 30
Current consumption (mA)
Depending on connected units, etc. See EBL128 Planning Instructions.
Ambient temperature (C)
Operating
storage
-5 to +40
-40 to +75
Ambient humidity (% RH)
max. 95, non condensing
Ingress Protection rating (estimated)
IP32
Inputs
1 COM loop for 128 addresses
1 programmable input. NO / NC (R>2K = open circuit). Max. 2 mA.
Alt. supervised, normally high resistance (3K3) or low (680R).
Outputs
1 programmable supervised voltage output (24 V DC, max. 500 mA)
1 programmable supervised voltage output (24 V DC, max. 200 mA)
1 programmable relay output. 1Default set for routing equipment (Fire
brigade tx).
1 non-programmable relay output. 1For routing equipment (Fault tx).
Power supply (24 V DC, max. 200 mA) for routing equipment
Power supply (24 V DC, max. 500 mA) for external equipment (Web-
server, up to 4 ext. FBPs, etc.) Web-server requires approx. 65 mA.
Interfaces
RS232 ("D" connector) for a PC (Win128)
RS232 for a Web-server 1598
Socket for an optional RS485 transceiver, for ext. FBPs, EPUs and/or
AAUs.
Size H x W x D (mm)
511 x 416 x 123
Weight (kg)
12.2 (Excl. Batteries)
Colour (metal cabinet)
Aluminium & light grey (NCS S1500-N, PMS Cool Grey 2)
Approvals
EC certificate no. 0786-CPD-20971
EN54-2:1997 / A1:2006, EN54-4:1997 / A2:2006
The Swedish front conforms to SS3654.
Note! All voltages are nominal. For more information see EBL128 Planning Instructions MEW00508.
1Relay contacts: max. 1 A @ 30 V DC.