Honeywell Notifier AM12-24 User manual

\
AM12-24
Conventional fire panel

AM-1224 Installation and programming manual INDEX
AM-1224_manu Doc. M-124.1-AM1224-ENG Rev A.1 NOTIFIER ITALIA
INDICE
DETECTION SYSTEM LIMITS 1
DESCRIPTION 2
Mainfeatures 2
ELECTRICAL FEATURES 3
INSTALLATION 4
Detectionlines 5
Characteristics of relay outputs 6
Lines connections 6
AuxiliaryAlarmdevices 7
MainBoard 7
Line expansion card (line 13 ÷ 24) 9
16 Outputs optional card 10
Display board – Front Panel 11
FRONT PANEL 12
Front panel commands and indications 12
Visual indication of the Front panel indications 13
USER INTERFACE DESCRIPTION 14
Keyboard operation for the data input in the programming file 14
Stand-by condition 15
RECOMMENDED SEQUENCE FOR CONTOL PANEL CONFIGURATION 16
Display in Zone Alarm condition 17
Display in Zone Fault condition 17
Display in System Trouble condition 18
Display in Zone Test condition 19
Displaying lists devices and areas excluded 19
CONFIGURATION MENÙ 20
Systemmenù 20
Expansion 20
Timing 21
Password 22
System 22
Detectorline 23
Auxiliaryinput 24
Output 25
Zone 26
Up/Download 26
Clear configurations 26
UTILITY MENÙ 27
Date and Time 27
Historylog 28
Viewandprint 28
Reset 28
Status Reading/ Status Change 29
MASK MENÙ 30
TEST MENU’ 35
Description auxiliary inputs 37
Appendix “A” –CONTROL BY EVENT EQUATION 38

AM-1224 Installation and programming manual PAGINA - 1
AM-1224_manu Doc. M-124.1-AM1224-ENG Rev A.1 NOTIFIER ITALIA
NOTE: Do not try to install the control unit and devices connected without reading this manual.
DETECTION SYSTEM LIMITS
An alarm or fire detection system can be very useful for the prompt warning of any dangerous event, such as fire, a robbery
or a simple burglary, in some cases it can automatically manage events (transmission of messages for room evacuation,
automatic fire-extinguishing, TVCC system interface, access route or door blockage, automatic warning to authorities, etc.),
but in any case, it does not ensure protection against damages to propriety or damages caused by fires or robberies).
Moreover, each system may not properly operate if it is not installed and maintained according to the manufacturer’s
instructions.
PRECAUTIONS
These instructions contain procedures to be followed in order to avoid damages to
equipment. It is assumed that the user of this manual has performed a training course and
that he knows the applicable rules in force.
The system and all its components must be installed in an environment having the following
features:
Temperature: -5 °C ¸ +40 °C.
Humidity: 10 % - 93 % (without condensation).
Peripheral devices (sensors, etc.) which are not perfectly compatible with the control unit
may cause damages to the same control unit, and a bad operation of the system in any
moment. Therefore, it is essential to only use material which is guaranteed by NOTIFIER
and is compatible with its own control units.
Please consult NOTIFIER Technical Service for any doubt.
This system, like all solid state components, may be damaged by induced electrostatic
voltages: handles the boards keeping them among the edges and avoid to touch the
electronic components.
An appropriate earthing connection ensures, in any case, a sensitivity reduction to
disturbances.
Please consult NOTIFIER Technical Service if you cannot solve installation problems.
Any electronic system does not operate if it is not powered.
If power supply from the mains fails, the system ensures its operation through battery, but
only for a limited period of time.
During the system planning phase, take into account the autonomy required to appropriately
dimension the power supply and batteries.
Skilled personnel shall periodically check the state of batteries.
Disconnect the MAINS and the batteries BEFORE removing or inserting any board.
Disconnect ALL power supply sources from the control unit, BEFORE performing any
servicing.
The control unit and the connected devices (sensors, modules, annunciators, etc.) may be
damaged, if a new board is inserted or removed, or if the powered cables are connected.
The most common cause for malfunctioning is inappropriate maintenance.
Take special care of these aspects since you start the system planning phase; this will
facilitate future servicing and will reduce cost.
This device is marked CE to certify it is in conformity with the requirements of the European
community Directives:
Electromagnetic Compatibility Directive 89/336/EEC (and the directive 92/23/EEC)
Low Voltage Directive 73/23/EEC
NATIONAL RULES
This device must be installed and must operate in accordance with these instructions
and to the rules in force in the installation place.

PAGINA - 2 Installation and programming manual AM-1224
NOTIFIER ITALIA Doc. M-124.1-AM1224-ENG Rev A.1 AM-1224_manu
D
De es sc cr ri ip pt ti io on n
AM1224 is a zone fire detection panel designed to comply the EN54.2 and EN54.4 European rules.
The panel in the standard configuration have 12 detection lines ( zones) that can be expanded to 24 using an
option card.
In addition a second option card is available to provide 8 relays outputs and 8 Open Collector outputs.
Each output can be activated by use of the Control by Event programming .
The front panel user interface have a backlite LCD graphic display of 8 lines by 20 columns (128 x 64 pixel in
graphic mode)
The Am1224 panel give the user the possibility to install a conventional low cost fire detection system with
similar complexity as some advanced intelligent addressable systems.
The panel is compatible with all conventional field devices available by Notifier Italia
M
Ma ai in n f fe ea at tu ur re es s
User interface Software in one language (Italian as default) replaceable by PC
12 detection conventional lines expandable up to 24 with one option card
Up to 25 conventional detectors per line.
Optional 8 relay + 8 OC transistor outputs card
On board general Alarm and general Fault relay outputs., plus one Sounder supervised output.
4 digital programmable inputs
Internal History log for 500 events in non volatile memory
3 password level as per EN54.2 (operator, maintenance and programming )
Up to 16 characters programmable text description for zones , outputs and installation name
Up to 600 seconds programmable delay and activations timers.
Silence sounders inhibit timer ( up to 255 seconds )
Control by Event outputs programming with logic operators. (And, Or, Del, etc.)
Real time clock display
Keyboard with additional functions keys for simple operations.
Optional download-upload software PC compatible to configure the system

AM-1224 Installation and programming manual PAGINA - 3
AM-1224_manu Doc. M-124.1-AM1224-ENG Rev A.1 NOTIFIER ITALIA
E
EL LE EC CT TR RI IC CA AL L F FE EA AT TU UR RE ES S
Working temperature: -5°C +40°C.
Relative Humidity: 10% 93% (no condensation).
Storage temperature: -10°C +50°C.
Weigth: 4,7Kg
P
Po ow we er r s su up pp pl ly y
The internal power supply provide:
27,6 Vdc + 2 % - 10 %, 1,4 Adc with max. ripple 300 mV (summing panel power supply and outputs)
27,6 Vdc / 1A Battery charger.
B
Ba at tt te er ry y C Ch ha ar rg ge er r s se ec ct ti io on n
Output Voltage = 27,5V.
Output Current= 1A ~ 100 mVpp max (with temperature compensation).
Batteries = 2 x 12V - 7Ah.
Suggested Batteries :
Yuasa type NP7-12 o NP7-12FR (UL94) Faston - Capacity (20 Hr) = 12 V 7Ah
Dimensions = 151(b) x 65 (p) x 98 (h).
Fiamm type FG20721 o FGV20721 (UL94) Faston - Capacity (20hr) = 12 V 7.2Ah
Dimensions = 151(b) x 65 (p) x 98 (h).
Yuasa type NP18-12B o NP7-12BFR (UL94) Screw - Capacity (20hr) = 12 V 17,2Ah
Dimensions = 181(b) x 77 (p) x 98 (h).
Fiamm type FG21803 o FGV21803 (UL94) Screw - Capacity (20hr) = 12 V 18 Ah
Dimensions = 181(b) x 77 (p) x 167 (h).
The followings are thresholds for faults indication on the Battery charger section:
Battery exaust = 21,5 Vdc.
Difference between batteries thresholds = 3,4Vdc
Battery cut-out thresholds = 20Vdc.
Current from battery in standby condition without mains (no 230 Vac): 180 mA (12 lines with End of Line
resistor – no external loads – display OFF)
Current from battery in Alarm condition without mains (no 230 Vac) : 320mA
G
Gr ro ou un nd d
Gound connection must be wired following CEI and ISPELS rules (Italy) or equivalent for different country.
In any case must ground circuit must have a resistance less than 10Ohm (measured at drain-well with
equipment disconnected). The Earth connection on CNAL terminals is mandatory .
P
Pa an ne el l M Ma ai in ns s C Co on nn ne ec ct ti io on n
This panel must be supplied with mains . In case of Mains loss the panel can continue to be supplied by internal
batteries for some time. Mains line required characteristics are:
Voltage : 230 Vac mono-phase + 10% - 15%.
Frequency: 50 / 60 Hz.
Current from Mains: 0.45 Aac.
Note: Pay particular attention to don’t install the panel near high power
electromagnetic sources as Radio transmitters , electric motors and so on.

PAGINA - 4 Installation and programming manual AM-1224
NOTIFIER ITALIA Doc. M-124.1-AM1224-ENG Rev A.1 AM-1224_manu
I
IN NS ST TA AL LL LA AT TI IO ON N
DIMENSIONS FOR WALL MOUNTING
The control panel is designed for wall mounting through 4 blocking dowels (on brick walls) or thread studs (on
panels etc.) The maximum screw diameter is 5 mm.
The control panel should not be installed near heat sources (radiators, heaters, etc.).
The panel may be opened unscrewing the top cover.
Wires of detector lines, auxiliary devices and power supply may be passed into the panel using knock-out holes
running them along the cabinet internal side providing sufficient length especially for those connected to the
CNAL terminal block.
230 Vac wire power supply must be fixed inside of the control panel. For the 230 Vac wire power supply must
be interrupted by an external shut down switch.
For installation in a corner it is
necessary to have a distance of
280mm to let the frontal panel
open.
With 5 automatic blocks (brickwoork
wall) or selfscrew (prefabbricated
panel) it is possible tha wall mounting.
Diameter max of the selfcrew: 5mm
The contol panel has to be wall
mounted in order to allow a clear
visibility of the disply and an easy
access for the user.
For example 1.5 m height allow an
optimal display vision.

AM-1224 Installation and programming manual PAGINA - 5
AM-1224_manu Doc. M-124.1-AM1224-ENG Rev A.1 NOTIFIER ITALIA
M
Ma ai in ns s 2 23 30 0V Va ac c c co on nn ne ec ct ti io on ns s
The power supply cable must preferably pass near the relative terminal block.
The connection to the 230 V power supply shall be made through 3 conductors cable (phase, neutral, earth).
The registration of the earth conductor coming from the main shall be connected to the CNAL terminal block and
must be fixed to the cabinet so that it can not accidentally be teared from the terminal.
Power supply connection shall be made in the following sequence:
1 - Open the 230 Vac power supply general switch.
2 - Disconnect terminal block CNAL from the control panel.
3 - Connect the power supply cable.
4 - Reconnect terminal block CNAL.
5 - Close the mains general switch.
6 - Install and connect batteries as specified in this manual.
7 - Close the control panel.
D
De et te ec ct ti io on n L Li in ne es s
Detectors' connection line may be two wires (current consuming detectors) or three wires (separately powered
detectors with alarm on N.O. contact).
Wire type: preferably shielded – two conductors.
Table of minimum section of wire relating to distance:
Up to 500 mt. 2 x 0.5 mm²
Up to 1.000 mt. 2 x 1 mm²
Up to 1.500 mt. 2 x 1.5 mm²
Up to 2.000 mt. 2 x 2 mm²
Fino a 3.000 mt. cavo 2 x 3 mm²

PAGINA - 6 Installation and programming manual AM-1224
NOTIFIER ITALIA Doc. M-124.1-AM1224-ENG Rev A.1 AM-1224_manu
C
Ch ha ar ra ac ct te er ri is st ti ic cs s o of f r re el la ay y o ou ut tp pu ut ts s
EN54
!
EN54-2 7.7
Alarm Output
The General Alarm relay is a free voltage contacts output.
Note : To comply the EN 54.2. 7.7 don’t connect on this output remote warning
devices (as in example a telephone dialer) because the connection is not
supervised
F
FU US SE E L LI IS ST T
Name Description Electrical Features
F1 User output fuse Fast glass F1AL
F2 Sounder output fuse Fast glass F1AL
F3 Battery output fuse Resettable Fuse MFR250
F4 Mains (230Vac ) Fuse Fast glass F1AL
L
Li in ne es s c co on nn ne ec ct ti io on ns s: :
EN54
!
EN54-2 8.8
Fault Output
The general Fault relay is normally energized.
In Fault condition it will be de-energized.
Note: To comply the EN 54.2.7.7 don’t connect on this output remote warning
devices (as in example a telephone dialer) because the connection is not
supervised.
Detector
800 SERIES or ECO1000 SERIES
FUNCTION
General Alarm
General Fault
Feature
Max 2A resistive 30Vdc, NO-NC programmable by Jumper JALL
Max 2A resistive 30Vdc, NO-NC programmable by Jumper JGST
N. O. Call Point contact
2K7
1/4W
1K
1/4W

AM-1224 Installation and programming manual PAGINA - 7
AM-1224_manu Doc. M-124.1-AM1224-ENG Rev A.1 NOTIFIER ITALIA
A
Au ux xi il li ia ar ry y A Al la ar rm m d de ev vi ic ce es s
Through the sounder output,the control panel may drive a 24 Vdc sounder.
The panel checks permanently the control line integrity (against Cut and Short-circuit). For this function the
sounder shall have an end-of-line resistance.
The output is protected by a 1 A fuse.
M
Ma ai in n B Bo oa ar rd d
Note:
The polarity shown on CN0-5 and
CN0-6 aren’t in alarm condition
CN0-6
CN0-5
+
-
-
+
47K
Polarized
sounder
Not polarized
sounder
47K
Mains
Terminal
block
F1AL 230V
fuse Resettable
fuse MFR250
Power ON
LED
Battery
2x12V
CN
Terminal
block
CN
Terminal
block
Front
panel
board
terminal
block
Panel reset
button
JDSP:
Groun fault detection Jumper
Default: ON
Expansion board
terminal block
Ground
fault LED JALL: selection Jumper alarm
relay contact
Default: N.O.
JGST: selection Jumper
fault relay contact
Default: N.O.
F1AL 230V
fuse

PAGINA - 8 Installation and programming manual AM-1224
NOTIFIER ITALIA Doc. M-124.1-AM1224-ENG Rev A.1 AM-1224_manu
CN0 terminals
CN1 terminals
Terminal #
CN0 Description Note
1 ALARM Relay NO-NC
2 ALARM Relay Common
Max 2A resistive 30Vdc,
Contact NO-NC selectable via
JALL Jumper
3 FAULT Relay NO-NC
4 FAULT Relay Common
Max 2A resistive 30Vdc
Contact NO-NC selectable via
JGST Jumper
5
SOUNDER (–)
(shown polarity, normal condition)
6 SOUNDER (+)
(shown polarity, normal condition)
Protected with 1A Fuse
Total current: 1A (Sounder+User )
End of Line resistor: 47K 5%
7 TX
8 RX
9 GND
RS232 serial interface input
(used for UPLOAD)
10
11 + 24Vdc 1A User
12
13 GND User
Protected with 1A Fuse
Total current: 1A ( Sounder+User )
14 Auxiliary input (External power supply Fault indication)
15 Auxiliary input (level 2 access )
16 Auxiliary input (Evacuation)
17 Auxiliary input (Technical Alarm)
End of Line resistor 2k7 ohm 5% 1/4W
Terminal # CN1 Description Note
1 Line 1 - (GND)
2 Line 2 - (GND)
3 Line 3 - (GND)
4 Line 4 - (GND)
5 Line 5 - (GND)
6 Line 6 - (GND)
7 Line 7 - (GND)
8 Line 8 - (GND)
9 Line 9 - (GND)
10 Line 10 - (GND)
11 Line 11 - (GND)
12 Line 12 - (GND)
13 Line 1 +
14 Line 2 +
15 Line 3 +
16 Line 4 +
17 Line 5 +
18 Line 6 +
19 Line 7 +
20 Line 8 +
21 Line 9 +
22 Line 10 +
23 Line 11 +
24 Line 12 +
End of Line resistor
2k7 ohm 5% 1/4W