Satelec Implant Center 2 User manual

User’s manual • Manuel d’utilisation • Manual de uso
Benutzerhandbuch • Manuale d’uso • Handleiding voor de gebruiker
Manual de utilização • Användningshandbok • Εγχειρίδιο χρήσης

2

English 4
Français 32
Español 60
Deutsch 88
Italiano 116
Nederlands 144
Português 172
Svenska 200
Ελληνικά 228
3

4
1 INTRODUCTION 5
2 WARNINGS 5-7
3 DESCRIPTION 7
Physical description 7
Technical description 7-11
4 INSTALLATION / FIRST USE 11
Unpacking the device 11
Recommendations 11
Installation 11-12
First use 12
5 IRRIGATION SOLUTION 12
6 IRRIGATION LINES 12
7 ADJUSTMENTS / SETTINGS / MODES / INTERFACE
Startup 12
Settings 12
Irrigation function 13
Light function 13
I-SURGE function 13-16
PIEZOTOME function 16-17
NEWTRON function 17
Toolbox 17-19
8 SAFETY 19
9 USING THE DEVICE 19-21
10 SHUTTING DOWN THE DEVICE 21
11 ROUTINE MAINTENANCE / STERILIZATION 21
Irrigation line maintenance 22
Contra-angle maintenance 22
Rotary instruments maintenance 22
Device maintenance 22
Micromotor cord and scaler
cord maintenance 23
I-SURGE micromotor maintenance 23
Ultrasonic handpiece maintenance 24
Tip maintenance 24-25
12 MONITORING/ MAINTENANCE
Monitoring 25
Maintenance 25
Fuse replacement 25-26
Operation faults 26-27
13 ELECTROMAGNETIC COMPATIBILITY
Electromagnetic emissions 28
Electromagnetic immunity 29
Electromagnetic immunity /
Radiofrequency mobile equipment 29-30
Recommended separation distances 30
Cable lengths 31
14 DISPOSAL AND RECYCLING 31
15 MANUFACTURER'S LIABILITY 31
16 REGULATIONS 31
17 SYMBOLS 256-257
18 CUSTOMER RELATIONS
Manufacturer identification 260
Addresses of subsidiaries 260-261
The list of accessories referred to in this manual is non
exhaustive. Consult your local dealer for further
details.
ENGLISH
CONTENTS

5
I - INTRODUCTION
Congratulations! You have just taken possession
of your IMPLANT CENTER 2.
Designed by SATELEC®, the IMPLANT CENTER 2 is a
multifunction device intended for:
• dental implantology, with its I-SURGE micro-
motor.
• surgical procedures (osteotomy, osteoplasty,
periodontal and implant surgery) with its
PIEZOTOME or PIEZOTOME LED handpiece.
• mechanical ultrasonic treatment (prophylaxis,
periodontics, endodontics) with its NEWTRON or
NEWTRON LED ultrasonic handpiece.
The I-SURGE micro-motor coupling developed by
SATELEC means that the IMPLANT CENTER can be
used with most contra-angles (without internal
spray or light) found on the market.
In order to get the most out of this high-
technology device and ensure it has a long
working life, please read this manual carefully
before installing, using or maintaining it.
Points preceded by the symbol should be given
particular attention.
II - WARNINGS
CAUTION:
United States Federal Law restricts the use of
this device solely to qualified, trained and
competent dental health practitioners or under
their supervision.
The tips designed for PIEZOTOME 2 and IMPLANT
CENTER 2 are not compatible with PIEZOTOME and
IMPLANT CENTER, and vice versa.
To reduce the risk of accidents, the precautions
stipulated below must be taken:
Device users:
- Use of the IMPLANT CENTER 2 is restricted solely to
qualified, trained and competent dental health
practitioners in the normal context of their
work.
- If you have received this device by error, please
contact the supplier so that it can be removed.
Interactions:
- The IMPLANT CENTER 2 must not be used if the
patient and/or the operator has a cardiac
stimulator (pacemaker) or any other active
implant (e.g. a cochlear implant).
- The device complies with applicable
electromagnetic compatibility standards. The
user should nevertheless ensure that any
potential electromagnetic interference does
not cause an additional risk (presence of
radiofrequency emitters, electronic devices,
etc.).
- The device is not designed to withstand shocks
delivered by an electric defibrillator.
- Do not attempt to connect to the IMPLANT CENTER
2 any other accessories than those supplied by
SATELEC.

Electrical connection:
- Your IMPLANT CENTER 2 must be connected to the
electric power supply by a certified dental
installation technician.
- Warning: To avoid any risk of electric shock, this
device must be connected to an electrical
power supply with a protective ground.
- The electric supply to which the device is
connected must comply with the standards in
force in your country.
- If loss of electrical power during use is likely to
generate an unacceptable risk, the device must
be connected to a suitable power source (e.g.
UPS).
Using the device:
- Do not use the device if it appears to be
damaged or faulty.
- Turn the device off before unplugging the power
cord.
- To unplug the power cord, grip the cord plug
and hold the wall socket.
- Never use any other irrigation solution
containers than those intended for suspension
from the supplied brackets.
- The device must only be used with bottles or
bags of physiological saline or sterile water.
- The capacity of the irrigation solution
containers used must not exceed one litre.
- When the device is not to be used for a long
period of time, unplug the device from the
electric supply.
- Do not exert excessive force on the screen.
- Do not move IMPLANT CENTER 2 during use.
Environment:
- Do not cover the device or obstruct the
ventilation vents.
- Do not immerse the device in liquid, and do not
use it outdoors.
- Do not tilt the device at an angle greater than
5°.
- Do not place the device near a heat source.
- Make sure that the cords are not in a traffic
path.
- The device must be stored in its original
packaging in an appropriate and safe place.
- The device is not designed for use in the
presence of anesthetic gases or any other
flammable gas.
- Do not expose the device to water vapor, or
splashes.
- Any condensation inside an electrical device is
potentially dangerous.
- If the device is to be moved from a cold
environment to a hot one, it must not be used
until it has reached room temperature.
- The device is not designed to work near ionizing
radiation.
- Do not insert metal objects into the device (risk
of electric shock, short-circuit or projection of
hazardous substances).
Maintenance:
- Before and after each use, your IMPLANT CENTER 2
must be disinfected with SATELEC-approved
agents.
- Before each procedure, it is essential to make
sure that the accessories to be used have been
cleaned, disinfected and sterilized.
Accessories:
- The device has been designed and developed
for use only with SATELEC accessories to ensure
maximum safety and performance.
6

- Use of accessories from other manufacturers is
a potential hazard for you or your patients.
Repair:
- Warning: Do not repair or modify the device
without prior authorization from SATELEC.
- Warning: If the device is modified or repaired,
specific checks and tests must be performed to
ensure that the device can still be used safely.
- In the case of a fault, contact the supplier of
your device. Do not use unauthorized repairers,
who might make your device dangerous for you
and your patients.
If in any doubt, contact an approved dealer or our
customer support department:
- www.acteongroup.com
- E-mail: [email protected].
III - DESCRIPTION
3. 1 PHYSICAL DESCRIPTION
The IMPLANT CENTER 2 has the following
components:
- a control unit (Fig. 1),
- a multifunction footswitch (Fig. 11),
- a micro-motor cord with connectors (Fig. 1-2),
- two brackets for irrigation solution (Fig. 1-3),
- an I-SURGE micro-motor (Fig. 1-4) without
contra-angle,
- a grounded power cord (Fig. 1-5),
- an LCD (Liquid Crystal Display) touch screen
(Fig. 1-6),
- a motor cord connector (Fig. 1-7),
- two peristaltic pump housings (Fig. 1-8),
- a cord connector for the two ultrasonic
functions (Fig. 1-9),
- a NEWTRON scaler cord or PIEZOTOME 2 LED
handpiece with cord (Fig. 1-10) (according to
option),
- a NEWTRON LED handpiece or a PIEZOTOME 2 LED
handpiece with its cord (Fig. 1-11) (according to
option).
Located at the back of the unit are:
- 1 power cord socket with ground pin (Fig. 2-1),
- 1 footswitch connector (Fig. 2-2),
- 1 fan (Fig. 2-3),
- 2 bracket holders (Fig. 2-4),
- 1 power switch (Fig. 2-5).
3. 2 TECHNICAL DESCRIPTION
a) LCD touch screen
The LCD touch screen (Fig. 3) is used to define
the settings of your IMPLANT CENTER 2.
The IMPLANT CENTER 2 is adjusted by applying
moderate pressure to the screen keys.
Identification of key areas common to all modes
(Fig. 3):
- 4: Reduce irrigation flow rate.
- 5: Increase irrigation flow rate.
- 6: Reduce value.
- 7: Increase value.
Identification of information display areas
common to all modes (Fig. 3)
- 2: Irrigation flow rate value.
- 9: Operating fault indicator.
Identification of key areas common to all modes
that also display information (Fig. 3)
- 1: Flush/prime.
- 3: Irrigation ON/OFF.
- 8: Save, store data.
- 10: Select footswitch mode.
7

- 11: ON/OFF of light function on handpiece
- 12: Select mode (according to connected
handpiece type).
Key areas and displays specific to the selected
mode
PIEZOTOME mode:
Identification of information display areas (Fig. 4)
- 13: Selected program power level.
Identification of key areas that also display
information (Fig. 4)
- 14: Select program: D1, D2, D3, D4.
NEWTRON mode:
Identification of information display areas (Fig. 5)
- 15: Selected program power level.
Identification of key areas that also display
information (Fig. 5)
- 16: Select program: Soft, Medium, High, Boost.
I-SURGE mode:
Identification of information display areas (Fig. 6)
- 17: Contra-angle ratio.
- 18: Motor speed value.
- 19: Motor delivered torque value.
Identification of key areas (Fig. 6)
- 20: Adjust contra-angle ratio.
- 21: Adjust motor speed.
- 22: Adjust motor delivered torque.
Identification of key areas that also display
information (Fig. 6)
- 23: Select micro-motor rotation (clockwise or
counterclockwise).
- 24: Select program: P1, P2, P3, P4.
Contra-angle, speed and torque setting
adjustment page
Identification of common information display
areas (Fig. 7)
- 25: Contra-angle ratio.
- 26: Maximum delivered speed.
- 27: Maximum delivered torque.
Identification of common key areas (Fig. 7)
- 28: Exit from the page without changes.
- 29: Delete last character entered.
- 30: Return to main page and save settings to
screen memory.
- 31: Numeric keypad.
Preprogrammed contra-angle adjustment page
Identification of information display areas (Fig. 8)
- 38: Contra-angle ratio.
- 39: Motor speed value.
- 40: Motor delivered torque value.
Identification of key areas (Fig. 8)
- 32: Exit from the page without changes.
- 33: Select custom contra-angle.
- 34: Return to main page and save settings to
screen memory.
Identification of key areas that also display
information (Fig. 8)
- 35: Select a multiplier contra-angle.
- 36: Select direct contra-angle.
- 37: Select a divider contra-angle.
8

Startup page
Identification of key areas (Fig. 9)
- 41: Enter TOOLBOX mode.
Toolbox
Identification of information display areas (Fig.
10)
- 43: Audio volume symbol.
- 44: Screen brightness symbol.
- 45: Light off time-out symbol.
- 48: Relative audio volume value.
- 49: Relative brightness level value.
- 50: Selected time-out value.
- 51: Software version.
Identification of key areas (Fig. 10)
- 42: Reset factory configuration.
- 46: Reduce value.
- 47: Increase value.
- 52: Validate the configuration.
b) Control unit back panel
The power receptacle (Fig. 2-1) with its
grounding pin is used to connect the IMPLANT
CENTER 2 to the power supply using a plug-in
power cord.
The footswitch connector (Fig. 2-2) is used to
connect the IMPLANT CENTER 2 to the multifunction
control footswitch.
The fan (Fig. 2-3) protected by a metal grille,
keeps the IMPLANT CENTER 2 at its optimal
performance level.
The bracket holders (Fig. 2-4) are used to install
the brackets.
The power switch (Fig. 2-5) is used to switch the
device ON or OFF.
c) Control unit sides
The pump housings (Fig. 1-8) are designed to
accommodate SATELEC irrigation line cassettes.
The irrigation cassettes are installed by lifting
the pump covers and inserting the cassettes
horizontally into the cassette housings.
d) Front panel
- The left connector is designed to accept the
connector of the I-SURGE micro-motor cord. Only
a SATELEC micro-motor cord must be used.
- The right-hand connector is designed to accept
the connector of the NEWTRON / NEWTRON LED cord
or the connector of the PIEZOTOME 2 / PIEZOTOME 2
LED handpiece cord.
e) Control footswitch
Having access to a large number of functions on
the control footswitch allows the practitioner to
work in a perfectly sterile environment, avoiding
the risk of cross-contamination.
Once the various settings have been adjusted,
the user has no further need to touch the keypad.
Depending on the mode, the control footswitch
buttons have different functions.
I-SURGE mode:
Footswitch button definitions (Fig. 11):
- 1: I-SURGE motor control (ON/OFF or
progressive).
- 2: Rotation direction.
- 3: Change program (P1 to P4).
- 4: Irrigation ON/OFF.
- 5: Select active handpiece.
9

PIEZOTOME mode:
Footswitch button definition (Fig. 11):
- 1: Ultrasonics control (ON/OFF or progressive).
- 2: Flush/prime.
- 3: Change program (D1 to D4).
- 4: Irrigation ON/OFF.
- 5: Select active handpiece.
NEWTRON mode:
Footswitch button definition (Fig. 11):
- 1: Ultrasonics control (ON/OFF or progressive).
- 2: Flush/prime.
- 3: Change program (Soft to Boost).
- 4: Irrigation ON/OFF.
- 5: Select active handpiece.
f) Technical characteristics
Manufacturer: SATELEC
Device name: IMPLANT CENTER 2
Electrical power supply:
- Voltage: 100 VAC to 230 VAC.
- Frequency: 50 Hz/60 Hz.
- Rated power: 250 VA at 230 VAC.
I-SURGE function
Operation:
Intermittent service: 20 sec. ON / 30 sec. OFF at
2 N.cm
Output characteristics:
I-SURGE micro-motor speed: 100 rpm to
40 000 rpm
I-SURGE micro-motor torque: max. 6 N.cm
Irrigation flow rate: 10 to 120 ml/min. (nominal
value).
Adjustment in 10 ml/min. steps
Flush/prime flow rate: 120 ml/min.
PIEZOTOME function
Operation:
Intermittent service: 10 min. ON / 5 min OFF
Output characteristics:
No-load voltage: 250 volts (nominal value without
handpiece)
Min. ultrasonic frequency: 28 kHz
Irrigation flow rate: 10 to 120 ml/min. (nominal
value)
Adjustment in 10 ml/min. steps (nominal value)
Flush flow rate: 120 ml/min. (nominal value)
NEWTRON function
Operation:
Intermittent service: 10 min. ON / 5 min. OFF
Output characteristics:
No-load voltage: 150 volts (nominal value without
handpiece)
Min. ultrasonic frequency: 28 kHz
Irrigation flow rate: 10 to 40 ml/min. (nominal
value)
Adjustment in 1 ml/min. steps (nominal value)
Flush flow rate: 120 ml/min. (nominal value)
Protection
Electrical equipment class: Class 1
Electrical safety class:
Type BF in I-SURGE mode
Type BF in PIEZOTOME mode
Type BF in NEWTRON mode
Safety devices
Thermal safety shut off to avoid overheating of
the I-SURGE micro-motor
Safety shut off if internal malfunction
2 fuses (power cord receptacle): 5 mm x 20 mm -
2 AT for 100 VAC to 230 VAC
1 internal fuse not accessible to the user
reference F1: 5 mm x 20 mm – 10 AT / 250 VAC
10