Satellite Global II User manual

Assembly Instructions Global II Portable Restroom
with HD Extrusion Molding
10/17/2018 REVC 40243 INSTRUCTION- GB II HD EXT 1
2530 Xenium Lane North, Minneapolis, MN 55441
Telephone: [phone] Fax: [phone]
800-328-3332 / www.satelliteindustries.com

10/17/2018 REVC 40243 INSTRUCTION- GB II HD EXT 2
5

10/17/2018 REVC 40243 INSTRUCTION- GB II HD EXT 3
Tools Needed:
1. Drill / Driver 2. #10 Drill Bit 3. Rivet Gun
4. Phillips Screw Driver 5. 7/16” Deep Well Socket 6. Ratchet Wrench
Step 1: Assemble (3) side panels together using HD extrusion:
*Tip: It may help to place panel on table or a stack of tanks before assembly.
1. Slide the HD Extrusion between the (2) panels. Note: Side panels will be riveted together later
in the assembly process.
2. Repeat on other side.

10/17/2018 REVC 40243 INSTRUCTION- GB II HD EXT 4
Step 2: Assemble Base to side panels:
1. Butt bottom of the rear panel up against the runners.Align rear panel center hole with
center mark on base and fasten with Screw #13860. Finish remaining (4) holes.
2. Align side panel’s center holes with grooves on base sides down to top of base runner and
fasten with Screws #13860.
Step 3: Fasten Extrusion to Side Panels:
1. Using holes in Extrusion as a guide (on inside
of unit), drill out using a #10 drill bit. (6)
Places per side.
Warning: Drill through first layer of panel only.
2. Fasten Extrusion to panel with expanding
rivets #18755.
3. Repeat on other side.
19
BASE
24

10/17/2018 REVC 40243 INSTRUCTION- GB II HD EXT 5
Step 4: Fasten Tank to Unit:
1. Position tank against the back wall and attach the tank starting with each side. Have (1)
person stand in tank while lagging panels to tank. This ensures that the tank is in the
correct position. Tighten screws #13860 until rubber washer begins to flatten.
WARNING: DO NOT TO OVER TIGHTEN SCREWS.
2. See location chart below for screw location. Note: Do not use dimples if they don’t match
chart locations.
3. Fasten toilet seat.
19
19 19 19
Step 5:
Assemble Paperguard to unit:
1. Using #10 Drill Bit, Drill out the (4)
dimples on side panel as shown.
2. Fasten Toilet Paper Holder to unit
using (4) Rivets #11054
and (4) washers #11315. ( Washers
are installed on inside of paper holder.)
3. Insert spindle 22310 in paperholder.
7

10/17/2018 REVC 40243 INSTRUCTION- GB II HD EXT 6
Step 6: Assemble Urinal to unit:
1. Using #10 Drill Bit, Drill (2) holes in side panel at dimples.
2. Insert round tube of Urinal in tank urinal hole.
3. Use (2) rivets #11054 and (2) washers #11315. Washers are installed on inside of Urinal.
4. Fasten urinal to tank using 1 screw #13860 in dimple located on back of tank collar.
19
10
18
Step 7: Assemble Shelf to unit
1. Using #10 Drill Bit, Drill (2) holes in 2 side panels at dimples location. (see below)
2. Fasten Shelf to unit in rear left corner using (4) Rivets #11030 from the outside, through
panel and into holes in shelf. Use (2) back-up washers #11315 on outside 2 rivets only.
14
8
14
17

10/17/2018 REVC 40243 INSTRUCTION- GB II HD EXT 7
Step 8: Assemble coat hook to doorframe.
1. Drill at dimple using #10 drill bit and fasten Coat Hook to the frame
using Rivet #17436.
16
13
Step 9: Install Door Handle.
1. Assemble Door Handle to Door using (1) Screw #40052, (1) Washer Fender #11360, on
outside of front & (1) Handle #40057, (1) Washer Flat #12382 and (1) Nut #16307 on door inside.
2. Tighten nut using 7/16” Deep Well Socket & Phillips screw driver until threads are engaged with
nylon in lock nut, at least one full thread must be showing, otherwise nylon nut will loosen and fall off.
15
22
23 12
20

10/17/2018 REVC 40243 INSTRUCTION- GB II HD EXT 8
Step 10: Assemble Front to Panels.
1. Install HD Extrusions between the front and panel.
Note: Fasten front to panels using the same
method as STEP 3 Fasten Extrusion to Side
Panel. (6)Places per side using rivets #18755.
Warning: Do not drill through first layer of
panel or front only.
2. Repeat on other side.
24
Step 11: Assemble Front to Base.
1. Fasten Front to Dirt Buster Base use (6) screws #13860 through pre-drilled holes in
bottom of door frame. Install (2) screws through pre-drilled holes in bottom of door
frame left side & (2) screws through pre-drilled holes in bottom of door frame right side.
2. Open the door and install the final (2) screws #13860 through two pre-drilled holes
behind the door, near inside edge of frame, (1) left and (1) right side.
19
3

10/17/2018 REVC 40243 INSTRUCTION- GB II HD EXT 9
Step 12: Assemble Roof to unit.
1. Place roof on top of unit. Fasten roof to unit use (18) Rivets #11030 & (18) Washers #11315
Washers are installed on inside of unit.
Step 13: Assemble Vent Pipe to unit.
1. Insert Vent Tube through roof & down into
top of urinal tube & fasten vent pipe to
urinal tube using (1) screw #13860in
dimple located on back of tube.
19
11
17
14