SATO KEIRYOKI SK-RHC Series User manual

Instruction Manual
for
Optional Probes for SK-RHC Series Transmitters
Thank you for purchasing the SK-RHCS Series Optional Probes.
This product is designed to measure temperature and humidity by connection with SK-RHC series
transmitters. Do not use it for other purposes.
Read this manual thoroughly before using and keep the manual in a safe place for future references
whenever necessary.
Names of Parts
1. Model SK-RHCS-1 Probe (plug-in type)
(1) Probe cap
(2) Sensor unit
(3) Fixing screw
(4) Probe connector
2. Model SK-RHCS-2 Probe (with sensor cord type)
(1) Probe cap
(2) Sensor unit
(3) Fixing screw
(4) Probe connector
(5) Sensor section
(6) Sensor cord
Installing Probes
Install the temperature/humidity probe as follows:
Plug the sensor unit into side of the SK-RHC as shown in the picture and fix
the sensor unit with SK-RHC from back side using the fixing screw included.
To remove the unit, loose and remove the fixing screw and pull it straight out
of the sensor connector in the reverse direction of the installation.
* Do not plug in or disconnect the probe while the main unit is ON.
Never diagonal and force push connector avoiding damages.
Safety Precautions
To use the probes safely, follow the precautions below.
・Never use the unit in an environment other than standard atmosphere (air composition).
・Never touch the humidity sensor with bare hands.
・If the dew point is exceeded and condensation occurs, stop using and turn off the power immediately. Then
use it again after drying the sensor naturally at room temperature.
・These probes are not waterproof. Do not let the probes to get wet.
・Never drop the probe or knock it over.
・Measuring temperature and humidity outside the measurable range may cause malfunctions.
・Never disassemble or modify the sensors to avoid any malfunctions.
・Do not modify, forcibly pull, bend or tie the sensor cord. Placing heavy objects on the sensor cord or heating it
will also damage the cord.
・Do not immerse the probe into liquid.
For a repair or a calibration, contact us or the retailer from which the Datalogger or probe was purchased.
②
③④
①
①②
③④
⑤⑥

Specifications
Model
SK-RHCS-1
SK-RHCS-2
Cat. No.
No. 8921-00
No. 8922-00
Sensor
(Temp.)
Thermistor
(Hum.)
High Polymeric Resistance change humidity sensor
Measuring range
(Temp.)
-10.0 to 60.0°C
(Hum.)
20.0 to 95.0 % rh (at 23 °C)
Accuracy
(Temp.)
±0.5°C at 20.0 to 30.0°C
±1°C at other than above
(Hum.)
Refer to the graphs below
Materials
Sensor unit
ABS resin
Sensing part
ABS resin
ABS resin
Cord
---
PVC resin
Sensing section
ABS resin
Dimensions
Sensor unit
W 24 x H 121 x D 29 mm
W 24 x H 107 x D 29 mm
Sensing part
---
Ø19 x L118.5mm
Cord length
---
5 m
Weight
about 42 g
about 228 g
* The specifications and appearance subject to change without notice
3-4, Kanda-kajicho, Chiyoda-ku, Tokyo 101-0045 JAPAN
URL :http://www.sksato.co.jp/english/
M.09
10 20 30 40 50
30
10
80
70
60
50
40
90
6023
±3％rh
±4％rh
95
±7％rh
5
±4％rh
Accuracy of R. Humidity
Humidity(%rh) SK-RHCS-1 Humidity(%rh) SK-RHCS-2
Temperature(℃) Temperature(℃)
Humidity(%rh) SK-LTHⅡα-1 Humidity(%rh) SK-LTH
Ⅱα-2 SK-LTHⅡα-３
Calibrations may not be accurate.
10 20 30 40 50
30
10
80
70
60
50
40
90
6023
±3％rh
±4％rh
95
±7％rh
±7％rh
5
±4％rh
Calibrations may not be accurate.