Savage MODMASTER MULTI-FABRIC SOFTBOX Parts list manual

CONTENTS
(1) CONNECTOR DISK
(1) LARGE SOFTBOX COVER
(1) SOFTBOX CONNECTOR DISK COVER
(8) CONNECTOR RODS
(1) SILVER/GOLD CONNECTOR LINER
(4) SILVER/GOLD SOFTBOX LINER
(1) INTERNAL BAFFLE
(1) FRONT DIFFUSER
(1) GRID (1 1/2" X 1 1/2" SECTIONS)
(1) CARRY BAG
1) PLACE THE LARGE SOFTBOX COVER ON A
LARGE FLAT SURFACE WITH THE WHITE SIDE
FACING UP.
ASSEMBLY
Assembly & Usage
Instructions
MULTI-FABRIC
SOFTBOX
MODMASTER™
2) PLACE THE CONNECTOR DISK IN THE CENTER OF
THE LARGE SOFTBOX COVER WITH ALL ROD
CONNECTOR PORTS IN THE UPWARD POSITION.
3) SLIDE THE CONNECTOR ROD THROUGH THE FIRST WHITE
CHANNEL ON THE INSIDE OF THE SOFTBOX COVER AND KEEP
SLIDING UNTIL IT STOPS IN THE TOP POCKET OF THE COVER.
4) SLIDE THE BOTTOM OF THE CONNECTOR
ROD INTO A CONNECTOR HOLDER.
5) ALLOW THE CONNECTOR HOLDER TO
PIVOT UNTIL IT IS FLAT ON THE SURFACE
AND LOCKED.
6) REPEAT STEPS 3,4 AND 5, ATTACHING THE NEXT ROD
DIRECTLY ACROSS FROM THE FIRST. CONTINUE UNTIL ALL
RODS ARE ATTACHED AND LOCKED IN PLACE.
7) YOUR SOFTBOX SHOULD NOW HAVE AN
OCTAGONAL SHAPE. FLIP IT OVER AND
ATTACH THE DISK COVER, WORKING
YOUR WAY AROUND THE SOFTBOX
UNTIL YOU HAVE ATTACHED ALL 8 SIDES.
(8) IF USING THE SOFT WHITE COVER CONFIGURATION,
ATTACH THE FRONT DIFFUSER USING THE VELCRO EDGES
AND WORK YOUR WAY AROUND THE BOTTOM OF THE
VELCRO EDGES ON THE LARGE SOFTBOX COVER.
IF USING THE BOWENS MOUNT,
YOUR SOFTBOX IS READY TO USE.
YOU MAY LOOSEN THE KNURLED
KNOB ON THE INSIDE OF THE
CONNECTOR DISK TO ROTATE
THE SOFTBOX.
SEE REVERSE FOR ADDITIONAL
SOFTBOX CONFIGURATIONS.
SMALL SOFTBOX CONNECTOR DISK COVER
(SET ASIDE UNTIL STEP 7)

15 ATTACH GRID FOR MORE
DIRECTIONAL LIGHTING
9ATTACH INNER
DIFFUSER TO
VELCRO TABS
11 MAXIMIZE LIGHT OUTPUT
WITH SILVER REFLECTOR
LINERS
12
ALIGN AND ATTACH REFLECTIVE
LINERS TO INNER VELCRO STRIPS
14 CREATE WARM, FIRESIDE LIGHT
WITH GOLD REFLECTOR
LINERS
Assembly & Usage
Instructions
MULTI-FABRIC
SOFTBOX
MODMASTER™
WWW.SAVAGEUNIVERSAL.COM
(9) FOR EXTRA DIFFUSION, ADD THE INTERNAL BAFFLE
BY STICKING THE VELCRO TAB AT EACH CORNER OF THE
DIFFUSER TO THE VELCRO NEAR THE TOP OF THE WHITE
CHANNELS INSIDE THE SOFTBOX COVER.
(10) TO MAXIMIZE LIGHT OUTPUT, ADD THE SILVER/GOLD CONNECTOR
LINER AND THE SILVER/GOLD SOFTBOX LINER WITH THE SILVER SIDE UP.
(11) APPLY THE SILVER/GOLD CONNECTOR LINER BY ATTACHING
THE VELCRO EDGE TO THE BOTTOM HALF OF THE VELCRO
RING NEAR THE BOTTOM OF THE LARGE SOFTBOX COVER
WITH THE SILVER SIDE FACING UP.
(12) APPLY THE SILVER/GOLD SOFTBOX LINER BY FIRST
ATTACHING AT THE BOTTOM. START AT THE CENTER OF THE
LINER MAKING SURE THAT IT IS ALIGNED SO THAT THE SLIT
NEAR THE TOP IS LINED UP WITH THE VELCRO TAB NEAR THE
TOP, SO THAT THE VELCRO TAB CAN BE PULLED THROUGH
TO ATTACH THE INTERNAL BAFFLE.
(13) PRESS THE VELCRO ON THE LINER DOWN ALONG THE TOP
OF THE TOP HALF OF THE VELCRO RING ALONG THE INSIDE OF THE
SOFTBOX COVER. PRESS THE VELCRO DOWN AT THE TOP OF THE
SOFTBOX ALONG THE BOTTOM OF THE TOP VELCRO RING.
ATTACH THE FRONT DIFFUSER AND THE SOFTBOX IS READY TO
ATTACH TO THE LIGHT SOURCE.
ATTACH THE INTERNAL BAFFLE IF MORE DIFFUSION IS DESIRED.
(14) TO WARM THE LIGHT ON THE SUBJECT, REPEAT STEPS 12-14 WITH THE
GOLD SIDE TURNED OUT.
(15) ATTACH THE GRID FOR A MORE DIRECTIONAL LIGHT OUTPUT BY
FASTENING ALONG THE TOP EDGE OF THE SOFTBOX ABOVE THE FRONT
DIFFUSER.
EXPERIMENT WITH GOLD, WHITE AND SILVER COMBINATIONS TO
CREATE VARYING DEGREES OF LIGHT OUTPUT, WARMTH AND
SOFTNESS ON YOUR SUBJECT.