Savant PAV-SIPA50SM User manual

PAV-SIPA50SM / PAV-SIPA50SMV2 Quick Reference Guide | 009-1658-03
Copyright 2021 Savant Systems Inc. | 210719
45 Perseverance Way, Hyannis, MA 02601
Savant.com | 508.683.2500
1 of 3
Box Contents
(1) Savant IP Audio 50 (PAV-SIPA50SM-xx / PAV-SIPA50SMV2-xx)
(2) Enclosure Bracket (071-1103-xx)
(1) 2U Rack Bracket (071-1102-xx)
(1) Power Cord (064-0079-xx)
(4) #10x½ Screw (039-0405-xx)
(4) Push Rivet (039-0406-xx)
(6) M4 Screw (039-0403-xx)
(4) 4-pin Speaker Connector (028-0702-xx)
(2) 4-pin IR Connector (028-0703-xx)
(4) Rubber Feet (074-0655-xx)
(4) M3 Feet Screw (039-0407-xx)
(1) Product Regulatory Statement (009-1950-xx)
Specifications
Environmental
Temperature 32° to 104° F (0° to 40° C)
Humidity 10% to 80% Relative Humidity
(non-condensing)
Maximum BTU 750 BTU/HR
Power
Input Power 100/240V AC (50/60 Hz) 3.6A
Maximum Power 225W
Operating Parameters
Rated Power
(Speaker Output)
50 WPC at 8 ohms (THD+N < 0.1%)
70 WPC at 8 ohms (THD+N < 1.0%)
Frequency
Response 20 Hz - 20 kHz +/- 0.5 dB, speaker output
Signal-to-Noise
Ratio (SNR) >95 dB, speaker output
Supported Digital
Input Formats
44.1 kHz / 48 kHz / 96 kHz at 16-bit / 20-bit /
24-bit resolution
Networking
Supported
Standard
IEEE 802.1 AVB/TSN switches
IEEE 802.3 Ethernet
Regulatory
Safety and
Emissions
FCC Part 15B CE Mark C-Tick UL UKCA
RoHS Compliant
Supported Releases
PAV-SIPA50SM-xx da Vinci 8.8 and higher
PAV-SIPA50SMV2-xx da Vinci 9.4.2 and higher
Music Streaming
The Savant IP Audio 50 has a built-in single stream of Savant Music for easy
access to popular music streaming services. (Streaming service fees may
apply.)
Savant® IP Audio 50 with Savant Music (PAV-SIPA50SM / PAV-SIPA50SMV2)
Quick Reference Guide
Dimensions
Height Width Depth Weight
Device 3.03 in
(7.69 cm)
12.00 in
(30.5 cm)
14.17 in
(36.0 cm)
10.6 lb
(4.81 kg)
Shipping 8.27 in
(21.0 cm)
15.55 in
(39.5 cm)
19.41 in
(49.3 cm)
15.1 lb
(6.83 kg)
Rack Space 2U
Front Panel
G
FED
C
BA
APower LED
Green: System has power and is operating
normally.
Red: System is in standby mode and most of the
controller circuitry is powered down.
O: System is not receiving power.
B
Status LED
Green Blinking: Embedded system is ready, but
no communication has been established with the
host.
Green: Host has established communications
with the embedded system.
Red Blinking: Embedded firmware is running, but
has not received a DHCP IP Address.
Red: Host has determined the firmware needs to
be updated, but a problem occurred during the
process that will initiate a reset.
Amber Blinking: Embedded system has a valid
link local IP Address and is connecting to the
host.
Amber: Host is updating the embedded
firmware.
O: Embedded processor is resetting, or is
powered up, and is booting the embedded
firmware.
Hardware Failure: If a hardware failure occurs,
the status LED indication will be interrupted
every three seconds with a solid red indication.
For example, if the LED is blinking green when a
hardware failure occurs, the LED will
alternate between blinking green and solid red at
three-second intervals.
CRS232 LED Green: RS-232 serial port activity.
O: No RS-232 serial port activity.
D
IR LED Green: IR port signal activity.
O: No IR port activity.
E
On/O
Button
On: Fully enables all internal power rails and
processor.
O: Disables most internal power rails and
processor, but not internal AC/DC power supply.
Hold On/O button for about 5 seconds to place
into standby mode. The Power LED turns red.
Hold On/O button for about 1 second to take
system out of standby mode. The I/O power
switch on the back of unit must be On (I) to
enable this function. To turn the power o for the
entire system, press the I/O power switch on the
rear panel to O [O].
FReset Button
Resets the network.
Hold Reset Button for 5 seconds while powered
Onto clear network settings. Status LED will
rapidly blink red when reset is complete.
GZone
Protection
Red: Protection mode has been enabled to
protect a zone/channel; typically indicates
thermal protection, clipping or over current.
O: Zone is o and protection mode has not
been enabled.

PAV-SIPA50SM / PAV-SIPA50SMV2 Quick Reference Guide | 009-1658-03
Copyright 2021 Savant Systems Inc. | 210719
45 Perseverance Way, Hyannis, MA 02601
Savant.com | 508.683.2500
2 of 3
Expansion
Up to sixteen Savant IP Audio devices can be connected in a single
system, providing a virtual audio switch that can be configured to suit
almost any need.
Network Requirements
For information on network requirements, refer to the Savant Device
Networking Guidelines on the Savant Community.
Speaker Connections
-
R +
-
L +
Zone 1
432
1
Pin 1
Pin 2
Pin 3
Pin 4
Right -
Right +
Left -
Left +
Use white stripe
for positive (+)
Speaker wiring connections are made
using 4-pin Speaker Connectors
supplied with the device. The wire slips
into the hole and locks with a screw
located at the top of the connector.
Speaker connectors accept up to
12AWG speaker cable.
NOTES:
– Wire order shown does not represent any wiring standard. It may
be dierent than other models.
– While not shown in the diagram above, Zones 2 to 4 follow the
same wiring as Zone 1.
RS-232 Connections
Pins 7 and 8 are only required
for CTS/RTS handshaking.
Pin 1
Pin 2
Pin 3
Pin 4
Pin 5
Pin 6
Pin 7
Pin 8
No Connection
No Connection
No Connection
Ground (GND)
Receive (RXD)
Transmit (TXD)
Clear to Send (CTS)
Request to Send (RTS)
Pin 1 Pin 8
RJ-45 Connector
(Gold pins face up)
IMPORTANT: When wiring to
this port, do not connect any
wires within the cable that are
not required for
communication.
NOTES:
– CTS/RTS handshaking is supported for flow control based on the
profile used in the configuration.
– Wire coloring is included to identify the pins used for this
connection. Colors shown do not represent any wiring standard.
– The IP Audio 125 does not support RS-422/485.
RJ-45 to DB9 Adapter: Savant oers RJ-45 to DB9 adapters in a
variety of configurations that can be used for RS-232 control.
Refer to the RS-232 Conversion to DB9 and Pinout Application Note
located on the Savant Customer Community for more information on
RJ-45 to DB9 adapters.
Rear Panel
G
F
E
D
C
B
AL
K
JI
H
A
Speaker
Connections
(4) Speaker output zones
Uses 4-pin Speaker Connectors.
NOTE: Compatible with 8 ohm or
4 ohm speakers.
B
Analog
Preamp
Output
(1) Analog stereo line output (Left & Right)
Direct Line Level 2.1-VRMS Output.
CAnalog Input (2) Analog stereo inputs (Left & Right)
RCA line-level inputs; 22 kΩinput impedance.
DDigital Audio
Out
(1) Digital optical preamp output (TOSLINK), line-
level 96kHz/24-bit output, fixed volume.
EDigital Audio
In
(2) Digital optical audio inputs (TOSLINK)
Supports up to 96kHz/24-bit digital audio in;
PCM stereo format only.
FIR
(4) IR Ports
Uses 4-pin IR Connectors to send IR signals to
control devices with an IR input or IR receiver via
an IR flasher (5V tolerant only). See the IR Wiring
section for important precautions regarding IR
functionality before making any connections.
GRS-232
8-pin RJ-45 port used to transmit and receive
serial binary data to and from serial controllable
devices. CTS/RTS handshaking availability
based on component profile. See the RS-232
Connections section for pin-outs.
HEthernet
8-pin RJ-45 port
100 Base-T auto-negotiating port.
Supports Audio Video Bridging (AVB).
IEthernet
Activity LED
Green Blinking: Activity (Rx/Tx)
O: No Activity
JEthernet
Link LED
Green Solid: Ethernet Link is established (any
speed).
O: Ethernet link is not established.
KUSB USB 2.0 Type A (reserved for future use)
LPower Input
100/240V AC (50/60 Hz) 3.6A
Fuse: 250V 3.0A slow blow fuse; field replaceable
I/O (power switch):
I (On): Powers On the chassis.
O (O): Powers O the chassis.
IR Wiring
Pin 1
Pin 2
Pin 3
Pin 4
IR 1 -
IR 1 +
IR 2 -
IR 2 +
Use white stripe
for positive (+)
IR connections are made using
4-pin IR Connectors supplied with
the device. The wire slips into the
hole and locks with a screw
located at the top of the
connector.
IMPORTANT: IR Wiring Precautions
Ensure that all IR emitters are within 15 feet (4.6 meters) from the
controller’s location.
Use of 3rd party blinking IR emitters with Talk Back is not
recommended. These types of emitters can draw voltage away from
the IR signal that can degrade IR performance.
NOTE: While not shown in the diagram above, IR connections 3 to 4
follow the same wiring as 1 to 2.
432
1
- 1 + - 2 +

PAV-SIPA50SM / PAV-SIPA50SMV2 Quick Reference Guide | 009-1658-03
Copyright 2021 Savant Systems Inc. | 210719
45 Perseverance Way, Hyannis, MA 02601
Savant.com | 508.683.2500
3 of 3
Replace the Fuse
ELECTRIC SHOCK HAZARD: Disconnect the unit from AC power
by removing the power cord from the AC outlet and the unit before
replacing the fuse.
IMPORTANT: The orientation of the cartridge within the unit and
location of the fuse within the cartridge are crucial to proper
operation. Make note of the orientation of the cartridge and the fuse
location within the cartridge before removing.
1. Disconnect the unit from AC power by removing the power cord.
2. Open the fuse cover on the AC power input using a flat head
screwdriver or similar thin flat head tool. This will allow access to
the fuse cartridges.
3. Using a flat head screwdriver or similar thin flat head tool, gently
loosen the cartridge and pull both cartridges out of the unit slowly.
As each cartridge is removed, make note of the orientation, as it is
important to proper operation.
TIP: Mark the chassis and fuse holder with a marker in order to align
when replacing.
4. Inspect both fuses and remove either or both if damage is
suspected.
5. Gently place the new fuse(s) in the cartridge and place the
cartridge part way into the receptacle aligning it as defined in the
diagram.
6. Gently press on the cartridge the rest of the way until it seats into
the terminals at the rear of the slot.
NOTE: If any resistance is encountered during seating the cartridge,
DO NOT apply more pressure. Stop pressing on the cartridge, remove
it, verify the orientation, and repeat step.
Additional Documentation
Refer to the following documents located on the Savant Customer
Community for additional information.
– Savant IP Audio Deployment Guide (009-1571-xx)
– Savant Media Server/Savant Music Supported Streaming Services
Application Note
The Spotify Software is subject to third party licenses found here:
https://www.spotify.com/connect/third-party-licenses.
Installation
Rack Installation
The Savant IP Audio 50 device can be mounted in a 2U rack style
enclosure and is compatible with all standard 19-inch National
Electrical Manufacturers Association (NEMA) rack mounts. The 2U
Rack Bracket needs to be attached prior to mounting. See Savant IP
Audio Deployment Guide for more information.
Enclosure Installation
The Savant IP Audio 50 device can be mounted to a Structured Media
Enclosure. The Enclosure Brackets need to be attached prior to
mounting. For proper ventilation, louvered enclosure doors are
recommended. See the Savant IP Audio Deployment Guide for more
information.
A
B
Connection Pins Towards Unit
Open Side of Cartridge Towards Power Switch
A
B