Saxby 73716 Manual

Instruction leaflet
Motion LED Wall
73716, 73717
www.saxbylighting.com
For your safety, always switch off the supply before changing lightbulbs, or cleaning.
Waste electrical products should not be disposed of with household waste. Please recycle where facilities
exist. Check with your Local Authority or retailer for recycling advice.
Recycling advice
Safety information
Saxby Lighting. BH23 3PE
We recommend cleaning with a soft dry cloth.
Do not use solvents or abrasive cleaners as these could
damage the finish.
Do not clean the product with a pressure washer.
This LED is protected by a shade. This part must be replaced immediately should the shade become
cracked or damaged. This fitting must not be used without the shade in place.
Iss.2 21072017
• TheLEDModuleinthisproductisnonreplaceable
Fitting/replacing bulb
PIR Adjustment
1.Theunitmustbeinstalledinaverticalposition,and
fitted 1.8m - 2.5m above the ground.
2.The PIR sensor is set to 10 metres. The detection
angleissetat110degrees.Thedurationthatthelamp
stays on can also be altered from (10±5) seconds
to (4±1) minutes. Use a small screwdriver to adjust
the ‘TIME’ and ‘LUX’ screws. When adjusting the
sensitivity (detection distance) in daylight it will be
necessary to cover the sensor to simulate night time.

Thankyouforpurchasingthislightfitting.Pleasereadtheinstructionscarefullybeforeusetoensuresafeand
satisfactory operation of this product. Please retain these instructions for future reference.
Warning
This light fitting is Class 1 and must be connected to
an Earth circuit
Please read these instructions carefully before
commencing any work.
Thisunitmustbefittedbyacompetentandqualified
electrician.
Install in accordance with IEE Wiring regulations and
currentBuildingRegulations.
Topreventelectrocutionswitchoffatmainssupply
before installing or maintaining this fitting. Ensure
other persons cannot restore the electrical supply
without your knowledge. If you are in any doubt,
pleaseconsultaqualifiedelectrician.
Thislightfittingshouldbeconnectedtoacircuitwitha
30mARCDfitted.
If replacing an existing fitting, make a careful note of
the connections.
Thissystemcontainsnon-replaceablepartsand
cannot be serviced. If damage occurs the part should
be scrapped.
Waste electrical products should not be disposed of
with household waste. Please recycle where facilities
exist. Check with your local authority or retailer for
recycling advice.
ThisproductisratedatIP44.
Thisproductisnotsuitablefordimming.
Theentireunitgetshotwhilstonforaperiodoftime.
Specification
Voltage: 240V 50Hz a.c.
Lamp: 6WLEDModule-6000K/600lm
IP rating: 44
Layout
Installation & Wiring
Check that...
• You have correctly identified the wires.
• Theconnectionsaretight.
• No loose strands have been left out of the connection
block.
• Planthedesiredlayoutofthisfittingcarefully,
ensuring the cables will reach the distance between
the junction box and the light fitting
• Avoidlocatinganycablesinpositionsthatwould
cause a hazard. Position cables and junction boxes
(not supplied) away from areas where they may be
at risk from being cut, trapped or damaged
• Cablesinwallsmustbeprotectedusingsuitable
conduit or plastic trunking.
• Themainssupplycablemusthaveaminimumcross
sectional area of 1.0mm²
• Thisproducthasspecialprotectionagainstthe
ingress of moisture and is IP44 rated.
Existing fittings must be completely removed before
installation of a new product. Before removing the
existing fitting, carefully note the position of each set
of wires.
• Removethelampshadefromtheproductusinga
screwdriver.
• UnscrewScrewAandremovetheTransparent
TerminalCover.
• Holdtheproductinpositionandmarkthelocation
of the fixing holes. Sensor must be at the base, as
shown below..
• Threadthecablethroughtherubbergrommetinthe
back plate.
• Fixthewallbacktothewallusingthescrews
and plugs supplied. Ensure the wall is capable of
holdingtheweightoftheproduct.Takecaretoavoid
damaginganyconcealedwiringandpipes.The
correct fixings should be used for brick or cavity
walls.
• Wireasdetailedbelow.
Wiring Colours :-
L (Live) - Brown
N (Neutral) - Blue
Earth-Green/
Yellow
SWITCHEDLIVE
NEUTRAL(BLUE)
EARTH(GREEN/YELLOW)
BROWN(L)
NEUTRAL(N)
GREEN/YELLOW
SUPPLYL IGHTFITTING
Commissioning
• Reattachtheterminalcoveranddiffuser.
• Replacefuse or circuit breakerandswitchon.Your
light is now ready for use.
Te rminal
Cover
Diffuser