Scag Power Equipment GC-4D User manual

GRASS CATCHER
OPERATOR'S MANUAL
PART 03014
MODEL GC-4D
GRASS CATCHER GC-4D
5
7
12
1
10
9
12
27
6
3
8
11
13
4
SC300G
14
12

SAFETY INSTRUCTIONS
Your mower is only as safe as the operator! As with any type of power
equipment or accessory, carelessness or error on the part of the operator
may result in serious bodily injury. To reduce the potential for injury,
please read and follow these instructions on safe operation and be certain
that anyone using this accessory fully understands and complies with the
following instructions.
1. Read and understand the contents of this manual before operating your
machine with this accessory attached.
2. If a mechanism becomes clogged, stop the engine and wait for all moving
parts to stop before cleaning.
3. Before performing any maintenance or service, stop the machine and
remove the spark plug wire.
. Do not allow children to operate equipment with this accessory installed. Do
not allow adults to operate equipment with this accessory installed without
proper instruction.
5. Shut the engine off and wait until the blades come to a complete stop before
removing the grass catcher container.
6. If the discharge area should plug, shut the engine off and wait for all
movement to stop before removing obstructions.
7. This accessory, when installed, may change the performance and operation of
your machine. Be sure you have practiced operating your machine with this
accessory attached in a clear and open area before beginning to mow grass.
-Note-
If you are installing the catcher to a machine with an Advantage cutter deck,
you must also install the filler plate (item 15) to the cutter deck.
8. Hold the filler plate (item 15) to the front of the cutter deck as shown in figure 1.
Center punch the two hole locations in the cutter deck. Drill the holes at the
marked locations using a 1/8" drill bit, then finish drilling using a 9/32" drill bit.
9. Install the deck filler plate to the inside front of the Advantage deck using (2)
1/ -20 x 3/ " bolts and (2) 1/ -20 elastic stop nuts.

REMEMBER - YOUR MOWER IS ONLY AS SAFE AS THE OPERATOR!
FAILURE TO FOLLOW SAFE OPERATING PRACTICES
MAY RESULT IN SERIOUS INJURY.
This manual covers the operating instructions
and illustrated parts list for:
GC-4D Grass Catc er Accessories
Figure 1. Filler Plate Installation
Center punch
and drill these
two holes.
Align the front edge
of the filler plate with
the front edge of the
cutter deck.
03054126982

1
Ref. Part
No. Number Description
1 - Catcher Box (Not available as spare part)
2 46452 CoverWeldment W/Decal
3 42211 MountingBracket
4 46043 Pull Rope Assembly
5 04070-01 Eyebolt, 5/16-18 x 2.25"
6 04030-03 LockWasher, 5/16
7 04020-03 Nut, 5/16-18 Hex Head
8 04001-20 Bolt, 3/8-16 x 1.50" Hex Head
9 04041-07 Flat Washer, 3/8 (.391 x .938 x .105)
10 04021-09 Nut, 3/8-16 Elastic Stop
11 04001-10 Bolt, 5/16-18 x 1.25" Hex Head
12 04040-15 Flat Washer, 5/16 (.375 x .875 x .083)
13 04021-10 Nut, 5/16-18 Elastic Stop
14 48236 Decal, Danger
15 422592 Filler Plate, Chute Advantage Deck Only
16 04001-01 Bolt, Hex Head 1/4-20 x 3/4"
17 04021-08 Nut, Elastic Stop 1/4-20
GRASS CATCHER GC-4D
5
7
12
1
10
9
12
27
6
3
8
11
13
4
SC300G
14
12
15
16
17

NOTES

PART NO. 03014
REVISED PRINTING 2/02
PRINTED IN USA
© 2002
SCAG POWER EQUIPMENT
DIVISION OF METALCRAFT OF MAYVILLE