Scag Power Equipment GC-STT-6KH User manual

MODEL GC-STT-6KH
OPERATORS MANUALOPERATORS MANUAL OPERATORS MANUALOPERATORS MANUAL
OPERATORS MANUAL
THISMANUALCONTAINSTHEOPERATING
INSTRUCTIONS AND SAFETY INFORMA-
TIONFORYOURSCAGACCESSORY. READ-
ING THIS MANUAL WILL PROVIDE YOU
WITH MAINTENANCE AND ADJUSTMENT
PROCEDURESTOKEEPYOURACCESSORY
PERFORMING TO MAXIMUM EFFICIENCY.
THE SPECIFIC MODELS THAT THIS BOOK
COVERS ARE CONTAINED ON THE INSIDE
COVER. BEFORE OPERATING YOUR MA-
CHINE,PLEASE READ ALL THE INFORMA-
TION ENCLOSED.
PART NUMBER 03065
71
62 20
27
50 22
18
34
6
28 22
35 17
51 15
22 17
22 28 29
236
22
19 14
49
60
10
03054cover

FAILURE TO FOLLOW SAFE OPERATING PRACTICES
MAY RESULT IN SERIOUS INJURY.
* Keep all safety shields in place.
* Beforeperforminganymaintenanceorservice,stopthemachineand
remove the spark plug wire.
* Ifamechanismbecomesclogged,stopthe engine before cleaning.
* Keephands,feetandclothingawayfrompower-drivenparts.
* Readthismanualcompletelyaswell as the Operator's Manual that came
withyourmower.
* Keepothersoff thetractor (only one person at a time).
REMEMBER - YOUR MOWER IS ONLY AS SAFE AS THE OPERATOR!
Hazard control and accident prevention are dependent upon the awareness,
concern, prudence, and proper training of the personnel involved in the op-
eration, transport, maintenance, and storage of the equipment.
WARNING
Thismanualcovers theoperatinginstructions
andillustratedpartslistfor:
GC-STT-6KH with a serial number of 4590001-4599999
Alwaysusetheentireserialnumber listed on the serial number
tagwhenreferringto this product.

®
TABLE OF CONTENTS
I
SUBJECT PAGE
1.1 Introduction ........................................................................................................1
1.2 Direction Reference ..........................................................................................1
1.3 ServicingThe Engine.........................................................................................1
2.1 Safety and Operating Instructions.....................................................................1
3.1 Assembly Instructions.......................................................................................2
3.2 Discharge Boot Assembly.................................................................................2
3.3 Catcher Frame Assembly..................................................................................3
3.4 Bucket Cover Assembly ...................................................................................4
3.5 EngineMounting ................................................................................................4-5
3.6 Catcher Hose Installation ..................................................................................5
3.7 Weight Bar Installation .......................................................................................5
Illustrated Parts List.................................................................................................6-7
LimitedWarranty Statement...................................................................Inside Back Cover
Equipment & Engine
Training Council
c
MEMBER
WE SUPPORT OPE
TECHNICIAN
CERTIFICATION

1
1.1 INTRODUCTION
This manual has been prepared to provide the
information you need to correctly assemble, operate,
and maintain this grass catcher. Read it carefully and
keep it for future reference.
The replacement of any part on this product by other
than the manufacturer's authorized replacement part
may adversely affect the performance, durability or
safety of this product.
USE OF OTHER THAN ORIGINAL SCAG
REPLACEMENT PARTS WILL VOID THE
WARRANTY.
If additional information or service is needed that is
not outlined in this manual, please contact your Scag
Power Equipment dealer. Scag dealers are trained in
the latest service methods and carry a full line of Scag
replacementparts.
When ordering parts, always provide the complete
model and serial number of your catcher.
All information provided in this manual is based upon
information available at the time of printing. Scag
Power Equipment reserves the right to make chages at
any time without notice or obligation.
2.1 SAFETY AND OPERATING
INSTRUCTIONS
-Note-
To avoid personal injury, it is imperative that all
safety instructions be observed.
1. Readthis operator's manualand the
operator'smanualthat issuppliedwith the
machinethisattachmentisusedon.
A replacement manual is available from your
authorized Scag Service Dealer or by contacting:
Scag Power Equipment, Service Department at P.O.
Box 152, Mayville, WI 53050. Please indicate the
complete model and serial number of your Scag
product when ordering a replacement manual.
2. Never operate your mower without the complete
grass catcher, all guards and covers installed, or
the discharge chute properly installed.
3. Before removing the grass bucket, disengage the
mower, stop the engine on both the mower and
the grass catcher, and wait for all movement to
stop.
4. ALWAYS turn the engine OFF, remove the key
and wait for all movement to stop before
servicing or cleaning the mower or the grass
catcher.
5. Do not modify or alter any component of the
grass catcher attachment.
6. Do not allow any passengers to ride on the grass
catcher attachment or on the mower.
7. To reduce the risk of fire, keep the engine clean
and free of debris, or excess lubricants.
8. DO NOT add fuel to a running or hot engine.
Turn the engine OFF and allow it to cool before
re-fueling.
1.2 DIRECTION REFERENCE
The "Right" and "Left", "Front" and "Rear" of the
machine are referenced from the normal operating
position.
1.3 SERVICING THE ENGINE
The detailed servicing of the engine is not covered in
this manual. For service of the engine it is important to
contact your Scag Dealer or an authorized servicing
agent of the engine manufacturer. Any unauthorized
work done on the engine will void the warranty.

2
3.1 ASSEMBLY INSTRUCTIONS
-Note-
For any instructions referring to an item
number, refer to the illustrated parts breakdown
on pages 6 and 7. Use the illustrated parts list
as a reference when following the assembly
instructions.
1. Remove all packaging materials. Lay out the
mounting hardware and the catcher assembly
parts for easy access.
3.2 DISCHARGE BOOT ASSEMBLY
1. If your cutter deck does not have the two
discharge chute mounting holes, locate and center
punch the two hole locations in the cutter deck as
shown in figure 1. Drill the holes at the marked
locations using a 1/8" drill bit, then finish drilling
using a 13/32" drill bit.
2. Install the boot mounting support tabs (items 40
& 41) to the cutter deck, using (1) 5/16-18 x 1"
bolt, (1) 5/16-18 x 1-1/4" bolt and (2) 5/16-18
elastic stop nuts. Do not tighten the bolts at this
time.
3. Install the boot mounting bracket (item 39) to the
boot (item 66) in the holes toward the front of the
boot, using (2) 3/8-16 x 1" bolts, (2) 3/8" flat
washers and (2) 3/8-16 elastic stop nuts.
-Note-
If you are installing the catcher to a machine
with a 52" cutter deck, you must install the filler
plate (item 42) to the boot.
4. Install the filler plate (item 42) to the boot (52"
models only) in the rearward holes in the boot
using (2) 5/16-18 x 3/4" bolts, (2) 5/16" flat
washers and (2) 5/16-18 elastic stop nuts.
-Note-
If you are installing the catcher to a machine
with a Bahia cutter deck you must also install
the filler plate (item 43) to the cutter deck.
5. Hold the filler plate to the front of the cutter deck
as shown in figure 2. Center punch the two hole
locations in the cutter deck. Drill the holes at the
marked locations using a 1/8" drill bit, then finish
drilling using a 9/32" drill bit.
6. Install the deck filler plate (item 43) to the inside
front of the Bahia deck (52" & 61" Bahia decks
only), using (2) 1/4-20 x 3/4' bolts and (2) 1/4" x
20 elastic stop nuts.
7. Install the boot to the cutter deck by aligning the
holes in the boot mounting bracket with the holes
in the boot mounting support tabs.
8. Secure the boot to the cutter deck by inserting the
chute latch pin (item 45) through the holes in the
support tabs and the boot mounting bracket.
Secure the pin using the cotter pin provided in the
hardware package. Tighten the boot mounting
support tab bolts.
Figure 1, Hole Locations
9" 4.25"
3/4"
0305412698
Center punch
and drill these
two holes.
Align the front edge
of the filler plate with
the front edge of the
cutter deck.
03054126982
Figure 2, Bahia Filler Plate

3
PROPERLYPROPERLY
PROPERLYPROPERLY
PROPERLY
SERVICESERVICE
SERVICESERVICE
SERVICE
ENGINEENGINE
ENGINEENGINE
ENGINE
WITHWITH
WITHWITH
WITH
OILOIL
OILOIL
OIL
ANDAND
ANDAND
AND
FUEL.FUEL.
FUEL.FUEL.
FUEL.
3.3 CATCHER FRAME ASSEMBLY
1. On the LH side of the machine remove the two
bolts securing the pump mounting plate to the
machine. Align the holes in the hitch bracket
weldment (item 53) with the holes in the machine
frame. Install (2) 3/8-16 x 1-1/4" bolts into the
rear holes of the frame and the hitch bracket.
Install (2) 3/8-16 x 1" bolts into the front holes.
Secure using four 3/8-16 elastic stop nuts.
-Note-
Install the hitch bracket mounting hardware
from the inside of the machine through the
machine frame and then through the hitch
bracket. This will prevent the hardware from
interfering with the linkage.
2. Repeat step 10 on the RH side of the machine.
3. Install the 1/2-13 nut (item 19) onto the 1/2-13 x
1-1/2" bolt (item 14). Thread the bolt and nut
assembly into the boss on the catcher frame (item
49). Do not tighten at this time.
4. Align the pins on the catcher frame (item 49)
with the hitch brackets. Slide the catcher frame
into the tubes on the hitch brackets and secure
using the quick pins (item 32).
5. Adjust the 1/2-13 nut and bolt assembly, that
was installed onto the catcher frame in step 3,
so the head of the bolt rests against the belt cover
on the machine. Tighten the nut against the boss
to secure the bolt from moving.
6. Align the holes in the RH upright post weldment
(item 51) with the holes on the RH side of the
catcher frame. Place (2) 3/8" flat washers onto
(2) 3/8-16 x 3-1/2" bolts and insert the bolts into
the holes of the upright post and the catcher
frame.
7. Install the RH brace (item 36) to the RH upright
post. Secure using (1) 5/16-18 x 2-1/2" bolt, (1)
5/16" flat washer and (1) 5/16-18 elastic stop
nut. Secure the other end of the RH brace to the
catcher frame using (1) 5/16-18 x 1" bolt and (1)
5/16-18 elastic stop nut.
8. Slide the engine support frame (item 54) under
the catcher frame and install onto the bolts that
are inserted into the RH upright post and the
catcher frame. Secure using (2) 3/8-16 elastic
stop nuts and (2) 3/8" flat washers.
9. Install the LH upright support weldment (item
50) to the LH side of the catcher frame. Insert
(2) 3/8-16 x 3-1/2" bolts and (2) 3/8" flatwashers
into the holes of the upright post, the catcher
frame and the engine support frame. Secure
using (2) 3/8-16 elastic stop nuts and (2) 3/8"
flat washers.
10. Install the LH brace (item 35) to the LH upright
post. Secure using (1) 5/16-18 x 2" bolt, (1)
5/16" flat washer and (1) 5/16-18 elastic stop
nut. Secure the other end of the LH brace to the
catcher frame using (1) 5/16-18 x 1" bolt and (1)
5/16-18 elastic stop nut.
11. Install (1) 5/16-18 nut onto the eyebolt (item 34).
Install the eyebolt through the LH upright
support and secure with (1) 5/16-18 elastic stop
nut.
12. Install the heatshield (item 37) to the catcher
frame using (1) 5/16-18 x 3/4" carriage bolt, (1)
5/16" flat washer and (1) 5/16-18 elastic stop
nut.
13. Secure the 2 heatshields to the two upright
supports using (6) 5/16-18 x 3/4" carriage bolts,
(6) 5/16-18 elastic stop nuts. The heatshields
will mount on the outside of the supports and
have an air space between them when installed
properly.
14. Slide the bucket (item 57) onto the catcher frame
and secure using the rubber strap (item 62).
Hook one end of the rubber strap into the washer
welded onto the RH upright support and the
other end into the eyebolt bolted onto the LH
uprightsupport.

4
6. Align the rear set of holes in the cover bracket
weldment with the holes in the RH upright
support. Secure the cover bracket to the RH
support using (1) 3/8-16 x 2-1/2" bolt, (2) 3/8"
flat washers and (1) 3/8-16 elastic stop nut. Do
not overtighten. The cover must be allowed to
pivot on the upright support.
7. Pivot the molded top up and back allowing the
two spring anchors to become close enough to
install the two springs (item 69) onto the spring
anchors. Place the springs on the outside edge of
the anchors, so the bolts do not interfere. Pivot
the molded top down onto the catcher bucket.
8. Install (1) 3/8-16 x 2-1/2" bolt into the set of
holes located next to the pivot bolt in the cover
bracket weldment. Secure using (1) 3/8-16
elastic stop nut.
-Note-
This bolt must be installed to prevent the bucket
cover from flipping over.
9. Install the container latch (item 72) onto the LH
side of the molded top. Secure using (2) 1/4-20
x 1" bolts, (4) 1/4" flat washers and (2) 1/4-20
elastic stop nuts. Adjust the latch as necessary
to insure a tight fit between the cover and the
bucket.
3.5 ENGINE MOUNTING
1. Align theholes in theengine guard weldment
(item 55) with the mounting holes in the engine.
Insert (4) 5/16-18 x 1-3/4" bolts through the
holes in the engine and the engine guard
weldment.
3.4 BUCKET COVER ASSEMBLY
1. Align the holes in the filter frame (item 74) with
the holes in the molded top (item 70). Be sure
the venting slots are pointed away from the
operator. (see figure 3)
2. Align the three holes in the cover bracket
weldment (item 56) with the correct three holes in
the filter frame and the molded top as shown in
figure 3.
3. Install the 1/4" spacer (item 44) between the
cover bracket weldment and the filter frame at
the hole closest to where the cover bracket
mounts to the RH upright support. Insert (1)
1/4-20 x 1" bolt through the cover bracket, 1/4"
spacer, filter frame and molded top. Secure
using (1) 1/4" flat washer and (1) 1/4-20 elastic
stop nut.
4. Finish securing the cover bracket and the filter
frame to the molded top using the (7) 1/4-20 x 1"
bolts, (14) 1/4" flat washers, and (7) 1/4-20
elastic stop nuts. Use one flat washer by the
head of each bolt and one by each elastic stop
nut.
5. Install the grass filter (item 73) around the filter
frame. The elastic in the filter will go around the
lip that circles the filter frame located inside the
moldedtop.
Figure 3, Bucket Top
Venting Slots
Opening Away
From Operator Location of 1/4"
Spacer Between
Cover Bracket &
Filter Frame
Use One 1/4" Flat
Washer Between
Bucket Cover &
Elastic Stop Nut
Do Not
Overtighten
RH Upright
Support
Spring
Spring Anchor
Bucket Cover
Filter Frame
Cover Bucket
GCSTT99BT
Springswillbecome energized during
installation, use caution when
installing.
CAUTION:

5
2. Align the bolts that were inserted through the
engine and engine guard weldment with the
holes in the engine mounting frame (item 54).
Insert all four bolts into the holes in the engine
mounting frame and secure using (4) 5/16-18
elastic stop nuts.
3. Attach the engine exhaust deflector (item 64)
with the two screws provided, so that the
exhaust is deflected downward and at an angle
away from the operator.
4. Install the blower housing weldment (item 47) to
the engine using (4) 5/16-24 x 1" bolts and (4)
5/16"lockwashers.
5. Install the fan assembly (item 46) and key (item
31) to the engine crankshaft and secure using (1)
7/16-20 x 2" fine thread bolt, (1) 7/16" lock
washer and (1) 7/16" flat washer. Torque the
retaining bolt to 55 ft.lbs.
6. Install the inlet adaptor (item 48) to the blower
housingusing (6)5/16-18wing nuts.
-Note-
In order to prevent hot exhaust blowing on
the grass catcher engine you must remove
the exhaust pipe that is mounted to the
muffler on the main engine.
3.6 CATCHER HOSE INSTALLATION
1. Slide (1) 6-1/2" hose clamp (item 60) onto one
end of the 6" hose (item 58).
2. Slide (1) 6-1/2" hose clamp (item 60) onto the
other end of the 6" hose (item 58) and install
onto the blower housing outlet and secure using
the hose clamp.
3. Slide (2) 8-5/8" hose clamps onto the ends of
the 8" hose (item 59).
4. Install the 8" inlet hose onto the boot and secure
using the hose clamp. Install the free end of the
8" hose onto the inlet adaptor and secure using the
hose clamp. -Note-
When installing the STT Catcher onto a 52"
cutter deck, Approximately 6" of the hose will
need to cut off of the 8" inlet hose.
3.7 WEIGHT BAR INSTALLATION
1. Install the weight support bar (item 52) to the
front of the machine by resting it directly on top of
the caster support arms and sliding it tight against
the frame of the machine. Secure the weight bar
to the machine using (2) bar clamps (item 38), (4)
3/8-16 x 1-1/2" bolts and (4) 3/8-16 elastic stop
nuts.
2. Install the weight assemblies (item 75) to the
weight support bar and secure them to the bar
using the 1/2"x 6-1/4" pin and lanyard (item 33 &
67).
-Note-
Additional weight assemblies are available
through your Scag dealer.

6
GC-STT-6KH GRASS CATCHER
44
GCSTT99EXV
27
5
74
56
21
69
21 29
29 973
20 27 5
72
70
71
62 20
27
50 22
18
34
6
28 22
35 17 37 52 8
38
21
75
28 22
32
57
69 51 15
22 17
12 28
22 29
236
22
19 14
49
60
60
58
10 7
21 53
61
42
28
22
59
61 66 7
29
39
45
30
212
22
3
41 40
20 1
43
11
25
26
24
23
48
16
46
13
47
64
65
31
63
55
54
29
21
A
A
4
22
33 67
76

7
GC-STT-6KH GRASS CATCHER
Ref. Part
No. Number Description Ref. Part
No. Number Description
-Note-
Some of the hardware is common hardware and you may purchase it locally. Be sure that all bolts
purchased locally are a grade 5.
1 04001-01 Bolt, Hex Head, 1/4-20 x 3/4”
2 04001-09 Bolt, Hex Head, 5/16-18 x 1”
3 04001-10 Bolt, Hex Head, 5/16-18 x 1-1/4”
4 04001-12 Bolt, Hex Head, 5/16-18 x 1-3/4”
5 04001-14 Bolt, Hex Head, 1/4-20 x 1”
6 04001-17 Bolt, Hex Head, 5/16-18 x 2”
7 04001-19 Bolt, Hex Head, 3/8-16 x 1”
8 04001-20 Bolt, Hex Head, 3/8-16 x 1-1/2”
9 04001-31 Bolt, Hex Head, 3/8-16 x 2-1/2”
10 04001-32 Bolt, Hex Head, 3/8-16 x 1-1/4”
11 04001-38 Bolt, Hex Head, 5/16-18 x 3/4”
12 04001-53 Bolt, Hex Head, 5/16-18 x 2-1/2”
13 04001-56 Bolt, Hex Head, 5/16-24 x 1”
14 04001-71 Bolt, Hex Head, 1/2-13 x 1-1/2”
15 04001-77 Bolt, Hex Head, 3/8-16 x 3-1/2”
16 04001-88 Bolt, Hex Head, 7/16-20 x 2”
17 04003-12 Carriage Bolt, 5/16-18 x 3/4”
18 04020-03 Nut, 5/16-18”
19 04020-07 Nut, 1/2-13”
20 04021-08 Nut, Elastic Stop, 1/4-20”
21 04021-09 Nut, Elastic Stop, 3/8-16”
22 04021-10 Nut, Elastic Stop, 5/16-18”
23 04022-02 Wingnut, Elastic Stop, 5/16-18”
24 04030-03 Lockwasher, 5/16”
25 04030-05 Lockwasher, 7/16”
26 04040-11 Flat Washer, 7/16”
27 04040-14 Flat Washer, 1/4”
28 04040-15 Flat Washer, 5/16”
29 04041-07 Flat Washer, 3/8”
30 04062-02 Hair Pin Cotter, .080 x 1.19”
31 04063-06 Key, 1/4 x 1/4 x 1-1/2”
32 04066-03 Quick Pin
33 04067-06 Pin, 1/2 x 6-1/4”
34 04070-04 Eyebolt, 5/16-18 x 2-3/4”
35 422578 Brace, LH
36 422579 Brace, RH
37 422580 Heatshield
38 422586 Clamp, Bar
39 422588 Mounting Bracket, Chute
40 422589 Support, Chute Mounting
41 422590 Mounting Tab, Chute
42 422591 Filler Plate, Chute-52” Deck Only
43 422592 Filler Plate, Chute-Bahia Deck Only
44 43063 Spacer
45 44131 Latch Pin, Chute
46 45077 Fan
47 45080 Blower Housing Weldment
48 45081 Adapter Weldment, Blower Inlet
49 451023 Frame Weldment, Catcher
50 451024 Upright Post Weldment, LH
51 451025 Upright Post Weldment, RH
52 451026 Support Weldment, Weights
53 451027 Hitch Bracket Weldment
54 45371 Engine Mounting Frame
55 45374 Engine Guard Weldment
56 45429 Bracket Weldment, Cover
57 48133 Bucket
58 48135-04 Hose, 6” Dia x 34”
59 48135-09 Hose, 8” Dia x 53”
60 48136-01 Clamp, 6-1/2” Max Dia
61 48136-02 Clamp, 8-5/8” Max Dia
62 48137-01 Rubber Strap-34”
63 481564 Engine, 6HP Kohler
64 481697 Exhaust Deflector, Engine
65 481698 Screw, Kohler Special
66 481734 Boot
67 481737 Lanyard, Weight Pin
68 48236 Decal, Danger
69 48734 Spring
70 481745 Molded Top
71 422725 Heat Shield
72 48737 Container Latch
73 48738 Filter, Open Mesh
74 48739 Support, Filter
75 9009 Weight Assembly, GC-STT-6KH
76 48236 Decal, Danger

LIMITEDLIMITED
LIMITEDLIMITED
LIMITED WW
WW
WARRANTY- COMMERCIAL AARRANTY- COMMERCIAL A
ARRANTY- COMMERCIAL AARRANTY- COMMERCIAL A
ARRANTY- COMMERCIAL ACCESSORCCESSOR
CCESSORCCESSOR
CCESSORYY
YY
Y
AnypartoftheScagcommercialaccessorymanufacturedbyScagandfound,inthereasonablejudgmentofScag,
tobedefectiveinmaterialorworkmanship,willberepairedorreplacedbyanAuthorizedScagServiceDealerwithout
chargefor partsand labor.
TheScag accessory, including anydefectivepart, must bereturnedto an AuthorizedScagService Dealerwithin
thewarranty period. The expense of delivering the accessory to the dealer for warranty work and the expense of
returningitbacktotheownerafterrepairorreplacementwillbepaidforbytheowner. Scag’sresponsibilityinrespect
toclaimsislimitedtomakingtherequiredrepairsorreplacements,andnoclaimofbreachofwarrantyshallbecause
forcancellationorrescissionofthecontractofsaleofanyScagmachine. Proofofpurchasewillberequiredbythe
dealer to substantiate any warranty claim. All warranty work must be performed by an Authorized Scag Service
Dealer.
Thiswarrantyis limitedto90days from thedateof original retailpurchasefor any Scagaccessorythatis usedfor
commercialpurposes,oranyotherincome-producing purposeincludingrentaluse.
Thiswarranty does notcoverany accessorythathas beensubjecttomisuse, neglect,negligence,or accident,or
thathasbeenoperatedinanywaycontrarytotheoperating instructionsasspecifiedintheOperator'sManual. The
warranty does not apply to any damage to the accessory that is the result of improper maintenance, or to any
accessory or parts that have not been assembled or installed as specified in the Operator's Manual.
Thewarranty does not cover any accessory that has been altered or modified. In addition, the warranty does not
extendtorepairsmadenecessaryby normal wear, or by the use of parts or accessorieswhich,inthereasonable
judgment of Scag, are either incompatible with the Scag mower or adversely affect its operation, performance or
durability. This warranty does not cover engines and electric starters, which are warranted separately by their
manufacturer.
ScagPowerEquipmentreservestherighttochangeorimprovethedesignofanyaccessorywithoutassumingany
obligation to modify any accessory previously manufactured.
All other implied warranties are limited in duration to the 90 day warranty period. Accordingly, any such implied
warrantiesincluding merchantability, fitnessfora particular purpose,orotherwise, are disclaimedintheir entirety
aftertheexpiration oftheappropriateninety day warranty period. Scag’sobligationunder this warrantyisstrictly
andexclusivelylimitedtotherepairorreplacementofdefectivepartsandScagdoesnotassumeorauthorizeanyone
toassumeforthemanyotherobligation. Somestatesdonotallowlimitationsonhowlonganimpliedwarrantylasts,
so the above limitation may not apply to you.
Scagassumesnoresponsibilityforincidental,consequentialorotherdamagesincluding,butnotlimitedto,expense
forgasoline,oil,expenseofdeliveringthemachinetoanAuthorizedScagServiceDealerandexpenseofreturning
itbacktotheowner,mechanic’straveltime,telephoneortelegramcharges,rentalofalikeproductduringthetime
warrantyrepairsarebeingperformed,travel,lossordamagetopersonalproperty,lossofrevenue,lossofuseof
the mower, loss of time, or inconvenience. Some states do not allow the exclusion or limitation of incidental or
consequential damages, so the above limitation or exclusion may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

PART NO. 03065
PRINTED 8/98
PRINTED IN USA
©1998
SCAG POWER EQUIPMENT
DIVISION OF METALCRAFT OF MAYVILLE, INC