ScatterBox POE304 User manual

Quick Start Guide - qPOE304 Copyright 2021 System Q Ltd
1
6 Port 100Mbps PoE Switch
ScatterBox is a registered trademark of System Q Ltd
POE304 - Quick Start Guide
www.systemq.com/PDF
/manual/xPOE304.pdf
A PoE switch is a network switch which
has power over Ethernet built-in.
The PoE switch will detect whether the
load device is PoE compatible and
provide PoE power automatically and
network connection.
The unitsadd extra flexibility to a network
infrastructure thanks to 100 metre run
capabilities both in and out of them.
User Information
· The PoE Switch must be installed in a clean, dry
environment where it will not be exposed to high
temperatures, moisture or excessive dust.
· Do not touch the PoE Switch or any of its connections
with wet hands.
· Ensure the power is switched off if the PoE Switch is not
in use for a long period of time.
· There are no user serviceable parts in the PoE Switch
and opening or attempting to repair the product will
void the warranty.
· Only use the PSU originally supplied with the product.
· Do not install or use the device if the power cable is
damaged.
The Switches have different uses and setup options. Including providing power to PoE Cameras, and
providing network access to devices like computers.
Setup Options
Option 1
To power IP Cameras using the PoE switch
then connect the IP Cameras using
CAT5e/CAT6 Ethernet Cable, for longer
distances we recommend using high
quality cable, with solid copper cores.
Option 2
Provide network infrastructure to PoE and non-
PoE Devices, like computers, and other Network
devices..

Quick Start Guide - qPOE304 Copyright 2021 System Q Ltd
2This symbol indicates that equipment must not be mixed with general household waste. For treatment, recovery and recycling please return to your local designated
WEE/CG0783SS collection point as defined by your local council.
All specifications are approximate. System Q Ltd reserves the right to change product specifications or features without notice. Whilst every effort is
made to ensure that these instructions are complete andaccurate, System Q Ltd cannot be held responsible for any losses, no matter how they arise,
from errors or omissionsin these instructions,or the performance or non-performance of the equipment refered to.
6 Port 100Mbps PoE Switch
ScatterBox is a registered trademark of System Q Ltd
LED Status Indicators
LED
Condition
Status
Power
On
The switch is receiving power
Off
The switch is not receiving power
Network / Link
On
The port is connected
Off
No connection to the port
Flashing
The port is transmitting or receiving data
The VLAN switch allows separation between ports. As default VLAN is off, when VLAN is on
ports on the different blocks won’t be able to see each other. Note that the UPLINK does see
all ports so the separation is only between ports.
Troubleshooting
Problem
Possible Cause
Solution
No Power light on
Switch
No power to the device
Check power to device from external source. Check that
the power lead (IEC lead) is plugged in to the PSU and
the PSU is plugged into the switch.
Loose connection
Check that the power lead (IEC lead) is plugged in to the
PSU and the PSU is plugged into the switch.
Network light not
flashing
Poor quality cable or
termination
Check the Ethernet cabling to your device is of good
quality and is terminated correctly.
Connected devices
not powering
Poor quality cable or
termination
Check the Ethernet cabling to your device is of good
quality and is terminated correctly
Total power
consumption exceeded
Check the load devices are not above the total power
consumption of the switch.
Cable length
Check the distance of Ethernet cable to your device.
Ethernet cables have a 100m maximum length.
Slow flashing LEDs,
No network on load
devices
Faulty cable or device
Turn the power off to the switch & unplug the load
devices (Check Ethernet cabling to load devices). Leave
the switch turned off for 10 seconds and then power the
switch back up, plug each device back into switch
individually to help troubleshoot the suspect cable.
Specification
Downlinks
4 x RJ45
Uplinks
2 x RJ45
PoE
30W (Max per port)
Power
96W (Whole device maximum)
Bandwidth
10Mbps / 100Mbp
Use
Internal Use Only
Working Temperature
0°C ~ 40°C
Power Input
240V AC (Lead supplied)
Dimensions
(w)210 x (d)136 x (h)44.5mm