Schacht WW6711 User manual

Hand Bobbin Winder
Assembly InstructIons for
sIngle-end, double-end &
double-end lAce WInders
Find out more at schachtspindle.com
Schacht Spindle Company 6101 Ben Place Boulder, CO 80301
p. 303.442.3212 800.228.2553 f. 303.447.9273
© 2019 Schacht Spindle Company, Inc. 11.19
WW6713
R-WW-940102
WW6711
WW6712

– 2 –
SINGLE-END WINDER
PARTS
1X main assembly: clamp, base, and
upright with drive axle (metal)
1X drive wheel
3X 3/8" washers
1X 3/8" e-clip
1X drive belt
1X drive shaft (metal)
1X 5/64" hex wrench
HAND BOBBIN WINDER
Assembly InstructIons
DOUBLE-END WINDER
PARTS
1X main assembly: clamp, base,
and upright with drive center tip
(metal for regular and lace)
1X tail spindle with live center tip
(metal for regular, plastic for lace)
2X 5/16" x 15" metal rods
1X drive wheel
3X 3/8" washers
1X 3/8" e-clip
1X drive belt
1X 5/64" hex wrench
TOOLS
hammer
scrap block of wood
FIGURE 1: INSTALL TAIL SPINDLE (DOUBLE-END WINDER ONLY)
INSTALL THE TAIL SPINDLE
(DOUBLE-END WINDERS ONLY)
1. Place the main assembly on a corner
of a sturdy table, with the drive wheel axle
pointing toward the oor. Using a hammer
and a scrap piece of wood, tap one end of
each 5/16" metal rod into the holes on the
bobbin winder upright (Figure 1). The
rods will measure about 13-1/2" when
they are in all the way.
2. Attach the tail spindle: press the spring
clamp down and slide the spindle onto the
metal rods with the winding tips facing
each other (Figure 1).
3. Press the spring clamp and move the
tail spindle along the metal rods to t your
bobbins, spools, or pirns. The bobbin
winder wheel will turn easily when there
is as little tension as possible on the tail
spindle.
main assembly
upright
5/16" metal rods
drive wheel axle
spring clamp
main assembly base
drive belt
pulley
clamp
live center
axle & tip
drive center tip
tail spindle

– 3 –
INSTALL THE DRIVE WHEEL
(ALL WINDERS)
1. Clamp the bobbin winder base to a
table top. Place three 3/8" washers on the
drive wheel axle. Place the drive wheel on
the axle. Press the e-clip into the groove
on the end of the axle (Figure 2).
2. Install the drive band around the shaft
pulley and the drive wheel (Figure 3).
Double-end winders are ready for use; for
single- end, continue to the next section.
INSTALL THE DRIVE SHAFT
(SINGLE-END WINDER ONLY)
1. Place the drive shaft on the drive axle at
the top of the upright. Line up the set screw
in the long shaft with the at side of the
drive axle (Figure 3).
2. Tighten the set screw securely with
the hex wrench. The single-end bobbin
winder is ready for use.
FIGURE 3: INSTALL DRIVE SHAFT (SINGLE-END WINDER
ONLY)
drive axle
set screw
drive shaft drive band
drive belt
pulley
FIGURE 2: INSTALL DRIVE WHEEL (ALL WINDERS)
main assembly
base
main assembly
upright
drive wheel axle
clamp drive wheel
e-clip3/8"
washers

– 4 –
SWITCHING REGULAR & LACE TIPS
(DOUBLE-END WINDER ONLY)
The double-end winder comes with
drive center and live center tips already
installed. If you have regular and lace
winding tips, you can switch them to
handle different types of winding tasks.
1. Replace the drive center tip on the
main assembly upright (see Figure 1 on
page 2): use the hex wrench to loosen the
set screw in the tip and pull the tip off the
axle. Insert the new drive center tip rmly
on the axle and tighten its set screw.
2. Remove the installed live center axle
and attached tip from the tail spindle (see
Figure 1 on page 2): remove the e-clip at
the outer end of the axle. Slide the axle
and attached tip out of the tail spindle,
removing 3 washers, another e-clip, and
the spring.
3. Install the new live center axle and tip:
insert the axle through an e-clip, a washer,
the spring, and a second washer. Now
insert the axle through the tail spindle
from its inner side. Add the last washer
and secure the axle with the last e-clip,
clicking it into the groove at the end of the
axle (Figure 4). •
REGULAR TIPS
LACE TIPS
Helpful Hints for Using Your Bobbin Winder
If the drive belt stretches out of shape and slips, remove it, stretch a rubber
band over the groove in the wheel, then reinstall the drive band.
You can increase belt tension and traction by twisting the belt once in a gure
8 before placing it over the shaft pulley. Note that this will also reverse the
direction you are winding.
Replacement drive bands can be purchased at your local weaving shop or on the
Schacht website.
Your hand bobbin winder has been carefully designed for years of trouble-
free use. The bearings are all self-lubricating and under normal use should not
require further lubrication. If your bobbin winder becomes dicult to turn, add a
few drops of light machine oil (such as sewing machine oil) on each bearing.
FIGURE 4: INSTALLING THE LIVE CENTER
AXLE AND TIP
axle & tip
inner side of tail spindle